This study focused on a numerical second law analysis and optimisation of a receiver tube op- erating in a parabolic trough solar collector for small-scale application. The receiver functioned in a Rankine cycle. The focus was on entropy generation minimisation in the receiver due to the high quality exergy losses in this component. Water functioned as the working uid and was heated from ambient conditions (liquid) to a superheated state (vapour), consequently, the receiver tube was subject to both single phase as well as two-phase ow. Entropy generation in the receiver tube was mainly due to nite temperature di erences as well as uid friction. The contribution of each of these components was investigated. Geometrical as well as operating conditions were investigated to obtain good guidelines for receiver tube and plant design. An operating pressure in the range of 1 MPa (Tsat = 180 C) to 10 MPa (Tsat = 311 C) was considered. Furthermore a mass ow range of 0:15 kg=s to 0:4 kg=s was investigated. Results showed that beyond a diameter of 20 mm, the main contributor to the entropy generation was the nite temperature di erences for most conditions. Generally, operating pressures below 3 MPa showed bad performance since the uid friction component was too large for small operating pressures. This phenomenon was due to long two-phase lengths and high pressure drops in this region. The nite temperature di erence component increased linearly when the tube diameter was increased (due to the increase in exposed area) if the focused heat ux was kept constant. However, the uid friction component increased quadratically when the diameter was reduced. In general when the concentration ratio was increased, the entropy generation was decreased. This was due to more focused heat on each section of the receiver pipe and, in general, resulted in shorter receiver lengths. Unfortunately, there is a limit to the highest concentration ratio that can be achieved and in this study, it was assumed to be 45 for two-dimensional trough technology. A Simulated Annealing (SA) optimisation algorithm was implemented to obtain certain optimum parameters. The optimisation showed that increasing the diameter could result in a decrease in entropy generation, provided that the concentration ratio is kept constant. However, beyond a certain point gains in minimising the entropy generation became negligible. Optimal operating pressure would generally increase if the mass ow rate was increased. Finally, it was seen that the highest operating pressure under consideration (10 MPa) showed the best performance when considering the minimisation of entropy in conjunction with the maximisation of the thermodynamic work output. / Dissertation (MEng)--University of Pretoria, 2014. / tm2015 / Mechanical and Aeronautical Engineering / MEng / Unrestricted

In der vorliegenden Arbeit wird der Einsatz von Positronenemittern zur Bestimmung der Dichte eines zweiphasigen Mediums beschrieben. Zur Messung wird die Dichteabhängigkeit der Positronenreichweite ausgenutzt. Die Realisierbarkeit des Verfahrens wird zunächst in einer Computersimulation geprüft. Danach werden Experimente an einem hochauflösenden PET-Scanner vorgestellt. Bei diesen Experimenten wird die Dichteabhängigkeit der Reichweite von Positronen anhand von Modellmedien aus festen Schaumstoffen untersucht. Dabei werden die in der Computersimulation erzielten Ergebnisse bestätigt. Aus den experimentellen Ergebnissen wird ein Modell zur Beschreibung der Abnahme der Koinzidenzrate in Abhängigkeit von der Entfernung des Detektors von der Positronenquelle und der Mediendichte entwikkelt. Auf der Basis des Modells erfolgt die Konzipierung einer für die Dichtemessung optimierten Detektoranordnung. Die Funktionsweise dieses Detektorsystems wird in Form technischer Unterlagen und experimenteller Ergebnisse beschrieben. Mit dem optimierten Detektorsystem werden die Untersuchungen an den Modellmedien nochmals durchgeführt, wobei die bisherigen Ergebnisse bestätigt werden. Das beschriebene Meßverfahren dient der Bestimmung der mittleren Dichte in einem überwiegend gasförmigen Medium, wobei eine Mittelwertbildung über das Meßvolumen erfolgt. Das Verfahren kombiniert die Vorteile bekannter densitometrischer Meßmethoden auf der Basis einer Schwächung von Strahlung, indem die hohe Dichtesensitivität der Positronenstrahlung mit der relativ geringen Absorption der energiereichen Annihilationsquanten kombiniert wird.

In order to investigate the two-phase flow behaviour in a complex reactor-typical geometry and to supply suitable data for CFD code validation, a model of the hot leg of a pressurised water reactor was built at FZD. The hot leg model is operated in the pressure chamber of the TOPFLOW test facility, which is used to perform high-pressure experiments under pressure equilibrium with the inside atmosphere of the chamber. This technique makes it possible to visualise the two-phase flow through large windows, also at reactor-typical pressure levels. In order to optimise the optical observation possibilities, the test section was designed with a rectangular cross-section. Experiments were performed with air and water at 1.5 and 3.0 bar at room temperature as well as with steam and water at 15, 30 and 50 bar and the corresponding saturation temperature (i.e. up to 264°C). The total of 194 runs are divided into 4 types of experiments covering stationary co-current flow, counter-current flow, flow without water circulation and transient counter-current flow limitation (CCFL) experiments. This report provides a detailed documentation of the experiments including information on the experimental setup, experimental procedure, test matrix and on the calibration of the measuring devices. The available data is described and data sheets were arranged for each experiment in order to give an overview of the most important parameters. For the cocurrent flow experiments, water level histograms were arranged and used to characterise the flow in the hot leg. In fact, the form of the probability distribution was found to be sensitive to the boundary conditions and, therefore, is useful for the CFD comparison. Furthermore, the flooding characteristics of the hot leg model plotted in terms of the classical Wallis parameter or Kutateladze number were found to fail to properly correlate the data of the air/water and steam/water series. Therefore, a modified Wallis parameter is proposed, which takes the effect of viscosity into account.

In order to investigate the two-phase flow behaviour in a complex reactor-typical geometry and to supply suitable data for CFD code validation, a model of the hot leg of a pressurised water reactor was built at FZD. The hot leg model is operated in the pressure chamber of the TOPFLOW test facility, which is used to perform high-pressure experiments under pressure equilibrium with the inside atmosphere of the chamber. This technique makes it possible to visualise the two-phase flow through large windows, also at reactor-typical pressure levels. In order to optimise the optical observation possibilities, the test section was designed with a rectangular cross-section. Experiments were performed with air and water at 1.5 and 3.0 bar at room temperature as well as with steam and water at 15, 30 and 50 bar and the corresponding saturation temperature (i.e. up to 264°C). The total of 194 runs are divided into 4 types of experiments covering stationary co-current flow, counter-current flow, flow without water circulation and transient counter-current flow limitation (CCFL) experiments. This report provides a detailed documentation of the experiments including information on the experimental setup, experimental procedure, test matrix and on the calibration of the measuring devices. The available data is described and data sheets were arranged for each experiment in order to give an overview of the most important parameters. For the cocurrent flow experiments, water level histograms were arranged and used to characterise the flow in the hot leg. In fact, the form of the probability distribution was found to be sensitive to the boundary conditions and, therefore, is useful for the CFD comparison. Furthermore, the flooding characteristics of the hot leg model plotted in terms of the classical Wallis parameter or Kutateladze number were found to fail to properly correlate the data of the air/water and steam/water series. Therefore, a modified Wallis parameter is proposed, which takes the effect of viscosity into account.

Das Ziel des Vorhabens bestand in der Ertüchtigung von CFD-Codes für Wasser-Dampf-Strömungen mit Phasenübergang. Während CFD-Verfahren für einphasige Strömungen bereits breite Anwendung in der Industrie finden, steht ein entsprechender Einsatz für Zweiphasenströmungen auf Grund der komplexen Phasengrenzfläche und den davon beeinflussten Wechselwirkungen erst am Anfang. Für die Weiterentwicklung und Validierung geeigneter Schließungsmodelle werden experimentelle Daten mit hoher Orts- und Zeitauflösung benötigt. Solche Daten wurden an der TOPFLOW-Versuchsanlage des HZDR durch Kombination von Experimenten bei praxisnahen Parametern für die Reaktorsicherheit (große Skalen, hohe Drücke und Temperaturen) und innovativer Messtechnik gewonnen. Die Gittersensortechnik, mit der detaillierte Informationen über die Phasengrenzfläche gewonnen werden können, wurde in adiabaten Wasser-Luft-Experimenten sowie Kondensations- und Druckentlastungsexperimenten in einem großen DN200-Rohr eingesetzt. Umfangreiche Datenbasen mit hoher Qualität stehen im Ergebnis des Vorhabens zur Verfügung. Die Technologie für die schnelle Röntgentomographie, die Messungen ohne Strömungsbeeinflussung ermöglicht, wurde weiter entwickelt und in einer ersten Messserie erfolgreich eingesetzt. Hochaufgelöste Daten wurden auch in Experimenten zu verschiedenen Strömungssituationen (z.B. Gegenstrombegrenzung) in einem Modell des heißen Strangs eines Druckwasserreaktors gewonnen. Für die Wasser-Dampf-Experimente bei Drücken von bis zu 5 MPa wurde dabei erstmals die neu entwickelte innovative Drucktanktechnologie eingesetzt. Zur Ertüchtigung von CFD-Codes für Zweiphasenströmungen wurde das Inhomogene MUSIG-Modell für Phasenübergänge in Kooperation mit ANSYS erweitert und anhand der o.g. TOPFLOW-Experimente validiert. Außerdem erfolgten Verbesserungen u.a. für die Turbulenzmodellierung in Blasenströmungen sowie Simulationen zur Validierung der Modelle für Blasenkräfte und Blasenkoaleszenz und -zerfall. Ein wesentlicher Fortschritt wurde bei der Modellierung freier Oberflächen durch die Verallgemeinerung des AIAD-Modells erreicht. Die am Heißstrangmodell ermittelten Flut¬kurven können unter Nutzung dieses Modells in guter Übereinstimmung berechnet werden.

Direct Contact Condensation between steam and water as well as bubble entrainment below the water surface play an important role in different accident scenarios for light water reactors. One example is the emergency core cooling water injection into a two-phase mixture. It has to be considered for example to evaluate potential pressurized thermal shock phenomena. This report documents experiments conducted in flat basin inside the TOPFLOW pressure chamber aiming on the generation of a database useful for CFD model development and validation. It comprises 3 different setups: condensation at a stratified flow of sub-cooled water, condensation at a sub-cooled water jet and a combination of both phenomena with steam bubble entrainment. The documentation includes all details on the experimental set up, on experimental conditions (experimental matrices), on the conduction of the experiments, on measuring techniques used and on data evaluation procedures. In addition, selected results are presented.

Counter-Current Flow Limitation (CCFL) is of importance for PWR safety analyses in several accident scenarios connected with loss of coolant. Basing on the experiences obtained during a first series of hot leg tests now new experiments on counter-current flow limitation were conducted in the TOPFLOW pressure vessel. The test series comprises air-water tests at 1 and 2 bar as well as steam-water tests at 10, 25 and 50 bar. During the experiments the flow structure was observed along the hot leg model using a high-speed camera and web-cams. In addition pressure was measured at several positions along the horizontal part and the water levels in the reactor-simulator and steam-generator-simulator tanks were determined. This report documents the experimental setup including the description of operational and special measuring techniques, the experimental procedure and the data obtained. From these data flooding curves were obtained basing on the Wallis parameter. The results show a slight shift of the curves in dependency of the pressure. In addition a slight decrease of the slope was found with increasing pressure. Additional investigations concern the effects of hysteresis and the frequencies of liquid slugs. The latter ones show a dependency on pressure and the mass flow rate of the injected water. The data are available for CFD-model development and validation.

Der vorliegende Bericht gibt einen zusammenfassenden Überblick der im Vorhaben erreichten Ergebnisse. Ziel war die Qualifikation von CFD-Methoden für Zweiphasenströmungen mit Phasenüber¬gang. Dafür werden neuartige experimentelle Daten benötigt. Diese können an der TOPFLOW-Anlage des HZDR generiert werden, da die Anlage Experimente in für die Reaktorsicher-heits¬forschung relevanten Skalen und Parametern mit innovativen Messtechniken verbindet. Die experimentellen Arbeiten umfassen Untersuchungen zu Strömungen in vertikalen Rohren mit Hilfe der ultraschnellen Röntgentomographie, zu Strömungen mit und ohne Phasenübergang in einem Testbassin sowie zur Gegenstrombegrenzung in einem Heißstrangmodell. Diese werden im vorliegenden Bericht nur kurz dargestellt, da es zu allen 3 Versuchsserien ausführliche Dokumentationen in separaten Berichten gibt. Ein wichtiges Ergebnis der Arbeiten zur CFD-Qualifizierung ist der Erstellung des Baseline-Modellkonzepts sowie die Erstellung des Baseline-Modells für polydisperse Blasenströmungen. Damit wird ein wesentlicher Beitrag zur Erhöhung der Vorhersagefähigkeit von CFD-Codes auf Basis des Zwei- oder Mehr-Fluid-Modells erreicht. Das innovative Generalized Two-Phase Flow Konzept (GENTOP) zielt hingegen auf eine Erweiterung der Einsatzmöglichkeiten der Zweiphasen-CFD. In vielen Strömungen treten unterschiedlicher Morphologien der Phasen bzw. Strömungsformen parallel in einer Strömungsdomäne auf. Außerdem gibt es Übergänge zwischen diesen Morphologien. Mit dem GENTOP-Konzept wurde erstmals ein Rahmen geschaffen der die Simulation solcher Strömungen auf konsistente Art und Weise ermöglicht. Spezielle Modellentwicklungen erfolgten mit dem Ziel einer besseren Modellierung des Phasenübergangs.

<div>With the rapid development of the advanced two-phase flow experimental technologies, more experimental databases with extended measurement ranges have been established to support the two-phase flow model development. The advantage of the Two Fluid model in modeling the complex two-phase flow phenomena over the mixture models stands out. One key aspect in the Two Fluid model development is the accurate modeling of the interfacial area between phases, which is strongly related to the interfacial mass, momentum, and energy transfer. As a closure relation of interfacial area concentration (interfacial area per unit volume) for the Two Fluid model, the Interfacial Area Transport Equation (IATE) provides dynamic predictions on the interfacial area change. It substantially solves the shortcoming of using flow-regime-dependent empirical correlations that can introduce numerical discontinuities between flow regimes. </div><div><br></div><div>The IATE has been extensively developed over the past twenty-five years. Many studies targeted on improving its prediction capability by developing bubble interaction source terms based on their experimental data. </div><div>The existing models are usually based on medium and large flow channels, yet the models may not be physically fit the small flow channels. The major reason is that the wall effect can have a larger influence on the two-phase flow in a small flow channel, as the surface area to volume ratio greatly increases. Therefore, the primary objectives of this study are to physically investigate the wall effect on two-phase flow and develop a generalized IATE by extending the application range of existing IATE from large and medium flow channels to small flow channel.</div><div><br></div><div>To achieve the objective, this study established a rigorous database of air-water two-phase flows in a small diameter pipe with its inner diameter of 12.7 mm, focusing on the bubbly-to-slug transition regime. The experimental analysis was performed on the pipe wall effect on the interfacial characteristics, based on the current experimental database and the existing experimental database collected on vertical pipes of different sizes. It is observed that 1) the pipe wall effect can alter the non-uniform radial two-phase distribution; 2) the bubbly-to-slug flow regime transition in a small diameter pipe happens in a smaller void fraction than in a large diameter pipe; 3) the bubble coalescence phenomenon can be more dominant for small pipe flow, and an intensive intergroup transfer can happen for the two-group interfacial area transport in two-phase flows. </div><div>As the interfacial area transport is directly related to the two-phase geometrical configuration, the two-phase geometrical parameters, void fraction and relative bubble size, are identified as the key parameters for modeling.</div><div><br></div><div>In the modeling of IATE source terms, the high geometrical scalability of the model is realized by properly including the wall effect into the modeling consideration. The following major improvements on the existing models are: 1) the inertia subrange assumption on the turbulent-driven interaction is properly improved; 2) the bubble-induced turbulent-driven interactions such as wake entrainment is revised by considering the wall effect on the wake region. In summary, models of bubble interaction due to random collision, wake entrainment, turbulent impact, and shearing-off are revised based on the existing studies on the IATE source terms development. The newly proposed interfacial area transport models are evaluated against an experimental database with 112 test conditions in total from a wide range of experimental pipe diameters from 12.7 mm to 304.8 mm. The new models can accurately capture the drastic intergroup transfer of void fraction and interfacial area concentration between two groups in transition flows. Overall, the relative error of void fraction and interfacial area concentration comparing with the experimental data are within ±15\% and ±10\%, respectively.</div>

Pour satisfaire aux dernières réglementations en matière d'émissions, des progrès importants sont encore attendus des moteurs à combustion interne. De plus, améliorer l'efficacité du moteur pour réduire les émissions et la consommation de carburant est devenu plus essentiel qu'auparavant. Mais, de nombreux phénomènes complexes restent mal compris dans ce domaine, tels que le processus d'injection de carburant. Nombreux logiciels pour la dynamique des fluides numérique (CFD) prenant en compte le changement de phase (comme la cavitation) et la modélisation de l’injection ont été développés et utilisés avec succès dans le processus d’injection. Néanmoins, il existe peu de codes CFD capables de simuler avec précision des conditions d’injection transcritiques, à partir d'une condition de température de carburant sous-critique vers un mélange supercritique dans la chambre de combustion. En effet, la plupart des modèles existants peuvent simuler des écoulements à phase unique, éventuellement dans des conditions supercritiques, ou des écoulements diphasiques dans des conditions sous-critiques. Par conséquent, il manque un modèle complet capable de traiter les conditions transcritiques, y compris la transition de phase possible entre les régimes souscritiques et supercritiques, ou entre les écoulements monophasiques et diphasiques, de manière dynamique. Cette thèse a pour objectif de relever ce défi.Pour cela, des modèles d'écoulement diphasique compressible de fluide réel basés sur une approche eulérienne-eulérienne avec prise en compte de l'équilibre de phase ont été développés et discutés dans le présent travail. Plus précisément, un modèle à 6-équation entièrement compressibles incluant les équations de bilan des phases liquide et gazeuse résolues séparément ; et un modèle à 4-équation qui résout les équations des bilans liquide et gazeux en équilibre mécanique et thermique sont proposés dans ce manuscrit. L’équation d’état Peng-Robinson EoS est sélectionné pour fermer les deux systèmes et pour faire face aux éventuels changements de phase et à la transition ou à la séparation des phases. En particulier, un solveur d'équilibre de phase a été développé et validé. Ensuite, une série de tests académiques 1D portant sur les phénomènes d'évaporation et de condensation effectués dans des conditions sous-critiques et supercritiques a été simulée et comparée aux données de la littérature et aux résultats académiques disponibles. Ensuite, les modèles d'écoulement en deux phases entièrement compressibles (systèmes à 6-équation et à 4- équation) ont été utilisés pour simuler les phénomènes de cavitation dans une buse 3D de taille réelle afin d'étudier l'effet de l’azote dissous sur la création et le développement de la cavitation. Le bon accord avec les données expérimentales prouve que le solveur proposé est capable de gérer le comportement complexe du changement de phase dans des conditions sous-critiques. Enfin, la capacité du solveur à traiter l’injection transcritique à des pressions et températures élevées a été validée par la modélisation réussie de l’injecteur Spray A du réseau de combustion moteur (ECN). / To satisfy latest stringent emission regulations, important progress is still be expected from internal combustion engines. In addition, improving engine efficiency to reduce the emission and fuel consumption has become more essential than before. But many complex phenomena remain poorly understood in this field, such as the fuel injection process. Numerous software programs for computational fluid dynamics (CFD) considering phase change (such as cavitation) and injection modelling, have been developed and used successfully in the injection process. Nevertheless, there are few CFD codes able to simulate correctly transcritical conditions starting from a subcritical fuel temperature condition towards a supercritical mixture in the combustion chamber. Indeed, most of the existing models can simulate either single-phase flows possibly in supercritical condition or two-phase flows in subcritical condition; lacking therefore, a comprehensive model which can deal with transcritical condition including possible phase transition from subcritical to supercritical regimes, or from single-phase to two-phase flows, dynamically. This thesis aims at dealing with this challenge. For that, real fluid compressible two-phase flow models based on Eulerian-Eulerian approach with the consideration of phase equilibrium have been developed and discussed in the present work. More precisely, a fully compressible 6-equation model including liquid and gas phases balance equations solved separately; and a 4-equation model which solves the liquid and gas balance equations in mechanical and thermal equilibrium, are proposed in this manuscript. The Peng-Robinson equation of state (EoS) is selected to close both systems and to deal with the eventual phase change or phase transition. Particularly, a phase equilibrium solver has been developed and validated. Then, a series of 1D academic tests involving the evaporation and condensation phenomena performed under subcritical and supercritical conditions have been simulated and compared with available literature data and analytical results. Then the fully compressible two-phase flow models (6-Equation and 4-Equation systems) have been employed to simulate the cavitation phenomena in a real size 3D nozzle to investigate the effect of dissolved N2 on the inception and developing of cavitation. The good agreement with experimental data proves the solver can handle the complex phase change behavior in subcritical condition. Finally, the capability of the solver in dealing with the transcritical injection at high pressure and temperature conditions has been further validated through the successful modelling of the engine combustion network (ECN) Spray A injector.