O Brasil é um país de dimensões continentais, onde existe uma considerável distância entre a geração e os principais centros de consumo. Dessa forma, o estudo e desenvolvimento de novas tecnologias de transmissão a longas distâncias é de fundamental importância para o desenvolvimento do país. A solução mais utilizada atualmente é a transmissão em corrente alternada. Entretanto a transmissão em corrente continua também é uma solução viável para longas distâncias. O sistema brasileiro é composto principalmente por linhas 500 kV em corrente alternada (também há 230; 345; 440 e 750 kV), bem como em corrente continua (em ±600 e ±800 kV). O presente estudo apresenta uma solução de transmissão em corrente alternada por linhas de 1000 kV, que se mostrou mais econômico na transmissão de potências superiores a 3.500 MW e distâncias de 1400km. Nos próximos anos, a geração de energia elétrica no Brasil será expandida de forma significativa, ocorrerá um aumento principalmente na geração de energia eólica e solar, localizadas em sua maioria na região Nordeste do país. Esse aumento na geração exigirá a transmissão de grandes blocos de energia elétrica por distâncias significativas, devido à falta de proximidade entre a geração e os principais centros consumidores, que estão localizados no Sudeste. Neste estudo, serão mostradas as etapas de definição de condutor economicamente mais adequado e projeto da geometria da torre. Com base nos dados obtidos, será feita a avaliação do desempenho da linha 1000 kV, durante a operação normal de fluxo de carga, curtos-circuitos e estabilidade. / Brazil, a country of continental proportions, have significant distance between the power generation centers and the main consumer centers. In such way, the study and development of new transmission technologies over long distances is of fundamental importance for the development of the country. Nowadays, the most commonly used solution is alternating current transmission. However, direct current transmission is also a viable solution for long distances. The Brazilian system mainly consists of 500 kV alternating current lines (along with 230, 345, 440 and 750 kV) and direct current lines (± 600 and ± 800 kV). This study provides a solution for transmission in alternating current by lines of 1000 kV, which proved to be more economical in power transmission over 3,500 MW and distances beyond 1400km. In the coming years, the electric power generation in Brazil will expand significantly; a boost will take place mainly in wind and solar power generation, located mostly in the Northeast of the country. This generation expansion will require transmission of large blocks of electric power over considerable distances, due to the lack of proximity between generation sites and main consumer centers located in the Southeast. This study will show the setting stages of the most economically applicable conductor and tower geometry design. Based on the data obtained, the performance of the 1000 kV line will be evaluated during the regular load flow operation, short circuits and stability.

O Brasil é um país de dimensões continentais, onde existe uma considerável distância entre a geração e os principais centros de consumo. Dessa forma, o estudo e desenvolvimento de novas tecnologias de transmissão a longas distâncias é de fundamental importância para o desenvolvimento do país. A solução mais utilizada atualmente é a transmissão em corrente alternada. Entretanto a transmissão em corrente continua também é uma solução viável para longas distâncias. O sistema brasileiro é composto principalmente por linhas 500 kV em corrente alternada (também há 230; 345; 440 e 750 kV), bem como em corrente continua (em ±600 e ±800 kV). O presente estudo apresenta uma solução de transmissão em corrente alternada por linhas de 1000 kV, que se mostrou mais econômico na transmissão de potências superiores a 3.500 MW e distâncias de 1400km. Nos próximos anos, a geração de energia elétrica no Brasil será expandida de forma significativa, ocorrerá um aumento principalmente na geração de energia eólica e solar, localizadas em sua maioria na região Nordeste do país. Esse aumento na geração exigirá a transmissão de grandes blocos de energia elétrica por distâncias significativas, devido à falta de proximidade entre a geração e os principais centros consumidores, que estão localizados no Sudeste. Neste estudo, serão mostradas as etapas de definição de condutor economicamente mais adequado e projeto da geometria da torre. Com base nos dados obtidos, será feita a avaliação do desempenho da linha 1000 kV, durante a operação normal de fluxo de carga, curtos-circuitos e estabilidade. / Brazil, a country of continental proportions, have significant distance between the power generation centers and the main consumer centers. In such way, the study and development of new transmission technologies over long distances is of fundamental importance for the development of the country. Nowadays, the most commonly used solution is alternating current transmission. However, direct current transmission is also a viable solution for long distances. The Brazilian system mainly consists of 500 kV alternating current lines (along with 230, 345, 440 and 750 kV) and direct current lines (± 600 and ± 800 kV). This study provides a solution for transmission in alternating current by lines of 1000 kV, which proved to be more economical in power transmission over 3,500 MW and distances beyond 1400km. In the coming years, the electric power generation in Brazil will expand significantly; a boost will take place mainly in wind and solar power generation, located mostly in the Northeast of the country. This generation expansion will require transmission of large blocks of electric power over considerable distances, due to the lack of proximity between generation sites and main consumer centers located in the Southeast. This study will show the setting stages of the most economically applicable conductor and tower geometry design. Based on the data obtained, the performance of the 1000 kV line will be evaluated during the regular load flow operation, short circuits and stability.

In India, the natural energy resources (thermal and hydro) are unevenly distributed and are mostly present in the remote areas and the load centers are distributed across various regions of the country. Therefore high voltage lines have become necessary for the devel-opment of large interconnected power networks and for the reliable and economic transfer of power. The increase in electric power demand due to the electric load growth has lead to the expansion of the transmission systems to ultra high voltage levels. Presently, Ultra High Voltage (UHV) power transmission lines are being built to transfer large electric power to distant load centers from the generating stations. Increasing the line voltage increases the surge impedance loading, stability and the thermal capacity of the line. Lightning is one of the major causes for the line outages and interruptions of UHV power lines. A lightning strike generates a very large voltage leading to insulator puncture, melting, burning and pitting of conductors and the supporting hardware. Lightning can lead to transient over-voltages thus leading to ash-over in the power transmission lines which are dangerous for the power equipments as well as for the human beings working in the vicinity. Ground wires are used for the protection of overhead power transmission lines against a lightning stroke. The overhead ground wires are installed such that the lightning attaches to it and shunts the lightning current to the ground through the tower, thus protecting the phase conductors. Shielding failure happens when the lightning strikes the phase conductor instead of the ground wires. Lightning shielding failure is a major con-cern in UHV lines due to their large height, very high operating voltage and wide exposure area of the phase conductors. The lightning over-voltages injected on the phase conductor (shielding failure) nally reaches the substation causing serious threat to the substation components and can lead to temporary or permanent outage of the power transmission system. There have been cases of very high shielding failure ash-overs of UHV lines and thus lightning attachment to power transmission lines need to be studied in detail to reduce the power system line outages. Several models such as electro-geometric model (EGM) and leader progression model (LPM) have been developed to study the shielding failure of power transmission lines. EGM has been extensively used to obtain lightning attachment to power transmission lines but in recent years it is seen that EGM is unable to accurately predict the lightning attach-ment to UHVAC lines. The shielding failure rates obtained by EGM does not match with the observed shielding failure rate for UHV lines. For this reason LPM is considered to obtain lightning attachment to UHV lines but LPM in its initial stage do not deal with the detailed physics of the upward leader inception, i.e., corona inception and unstable as well as stable upward leader inception from the object on the ground. In this thesis a model for the lightning attachment has been developed based on the present knowledge of the lightning physics. The thesis mainly focuses on the modelling of upward leader inception and propagation for lightning attachment to UHV power trans-mission lines. Upward leader inception is modeled based on the corona charge present near the conductor region and the upward leader propagation model is based on the correlation between the lightning induced voltage on the conductor and the voltage drop along the upward leader channel. The present model considers corona inception and modelling of unstable and stable upward leader inception from the ground object for the analysis of the lightning attachment process. The upward leader inception model developed is compared with the previous inception models and the results obtained using the present and previous models are found to be comparable. Lightning striking distances ( nal jump) for various lightning return stroke current were computed for di erent conductor heights using present lightning attachment model. It is seen that the striking distance increases with the increase in lightning re-turn stroke current and increases with increase in conductor heights. The striking distance computed using the present model matches with the value calculated using the equation proposed by the IEEE working group for the applicable conductor heights of up to 8 m. The in uence of the conductor operating voltage, cloud electric eld, lightning down-ward leader lateral distance, conductor length, transmission line tower and conductor sag on the upward lightning leader inception are analysed and reported in the thesis. It is found that the lightning attraction to power transmission line increases with increase in conductor positive operating voltage and decreases with increase in conductor negative op-erating voltage. The presence of transmission line tower reduces the lightning attachment to the conductor lines and the probability of lightning strike decreases with the increase in downward leader lateral distance from the conductor lines. The present lightning attachment model is applied to study the shielding failure of UHV power transmission lines rated for 1200 kV ac (delta and horizontal con guration) and for 800 kV dc (with and without a dedicated metallic return conductor) and thereby the lightning shielding failure ash-over rate is computed for the UHV power transmission lines. It is seen that the lightning shielding rate for UHV power transmission lines depend on the lateral distance of the downward leader channel, instantaneous 50 Hz voltage on the transmission line conductor, height of the transmission line conductor, induced voltages on the conductor and the lightning return stroke current.

Ever increasing demand for electricity, exploitation of large hydro and nuclear power at remote location has led to power evacuation by long EHV/UHV transmission systems. This thesis concentrates on transient analysis of EHV/UHV transmission systems for improved planning and protection. In this thesis, the uncontrolled and controlled switching methods to limit the switching surges during energization of 765kV and 1200k VUHV transmission lines are studied. The switching surge over voltages during the energization of series compensated line are compared with uncompensated line. A Generalized Electromagnetic Transients Program has been developed. The program incorporates specific models for studying the effectiveness of various means for control of switching surge over voltages during UHV transmission line energization and also simulation of various types of faults. Since power grids may adopt next higher UHV transmission level 1200kV, these studies are necessary for insulation coordination as well as transmission line protection relay settings. A new fault detection/location technique is presented for transmission line using synchronized fundamental voltage and current phasors obtained by PMUs at both ends of line. It is adaptive to fault resistance, source impedance variation, line loading and fault incidence angle. An improved Discrete Fourier Transform (DFT) algorithm to estimate and eliminate the decaying dc component in a fault current signal is proposed for computing the phasors. The settings for digital distance relays under different operating conditions are obtained. The relay should operate faster and be more sensitive to various faults under different conditions without loosing selectivity. An accurate faulted transmission line model which considers distributed shunt capacitance has been presented. The relay trip boundaries are obtained considering transmission line model under realistic fault conditions. For different loading conditions ideal relay characteristic has been developed. The obtained trip boundaries can be used for proper settings of practical relay. An adaptive relaying scheme is proposed for EHV/UHV transmission line using unsynchronized/synchronized fundamental voltage and current phasors at both ends of line. For fault location, the redundancy in equations is achieved by using two kinds of Clarke’s components which makes the calculations non-iterative and accurate. An operator for synchronization of the unsynchronized measurements is obtained by considering the distributed parameter line model. The distance to fault is calculated as per the synchronized measurements. Support Vector Machine(SVM) is used for high speed protection of UHV line. The proposed relaying scheme detects the fault and faulted phase effectively within few milli seconds. The current and voltage signals of all phases at the substation are fed to SVM directly at a sampling frequency of 1.0kHZi.e20 samples/cycle . It is possible to detect faulted phase with in 3msec, using the data window of 1/4th cycle. The performance of relaying scheme has been checked with a typical 765kV Indian transmission System which is simulated using the developed EMTP.