Finite impulse response (FIR) digital filters are frequently used in many digital signal processing and communication applications, such as IS-95 CDMA, Digital Mobile Phone Systems (D-AMPS), etc. FIR filter achieves the frequency response of system requirement using a series of multiplications and additions. Previous papers on FIR hardware implementations usually focus on reducing area and delay of the multiple constant multiplications (MCM) through common sub-expression elimination (CSE) in the transpose FIR filter structure. In this thesis, we first perform optimization for the quantization of FIR filter coefficients that satisfy the target frequency response. Then suitable encoding methods are adopted to reduce the height of the partial products of the MCM in the direct FIR filter structure. Finally, by jointly considering the errors in the truncated multiplications and additions, we can design the hardware-efficient FIR filter that meets the bit accuracy requirement. Experimental results show that although CSE in the transpose FIR structure can reduce more area in MCM, the direct form takes smaller area in registers. Compared with previous approaches, the proposed FIR implementations with direct form has the minimum area cost.

Power has become an important design closure parameter in today’s ultra low submicron digital designs. The impact of the increase in power is multi-discipline to researchers ranging from power supply design, power converters or voltage regulators design, system, board and package thermal analysis, power grid design and signal integrity analysis to minimizing power itself. This work focuses on challenges arising due to increase in power to power grid design and analysis. Challenges arising due to lower geometries and higher power are very well researched topics and there is still lot of scope to continue work. Traditionally, designs go through average IR drop analysis. Average IR drop analysis is highly dependent on current dissipation estimation. This work proposes a vector less probabilistic toggle estimation which is extension of one of the approaches proposed in literature. We have further used toggles computed using this approach to estimate power of ISCAS89 benchmark circuits. This provides insight into quality of toggles being generated. Power Estimation work is further extended to comprehend with various state of the art methodologies available i.e. spice based power estimation, logic simulation based power estimation, commercially available tool comparisons etc. We finally arrived at optimum flow recommendation which can be used as per design need and schedule. Today’s design complexity – high frequencies, high logic densities and multiple level clock and power gating - has forced design community to look beyond average IR drop. High rate of switching activities induce power supply fluctuations to cells in design which is known as instantaneous IR drop. However, there is no good analysis methodology in place to analyze this phenomenon. Ad hoc decoupling planning and on chip intrinsic decoupling capacitance helps to contain this noise but there is no guarantee. This work also applies average toggle computation approach to compute instantaneous IR drop analysis for designs. Instantaneous IR drop is also known as dynamic IR drop or power supply noise. We are proposing cell characterization methodology for standard cells. This data is used to build power grid model of the design. Finally, the power network is solved to compute instantaneous IR drop. Leakage Power Minimization has forced design teams to do complex power gating – multilevel MTCMOS usage in Power Grid. This puts additonal analysis challenge for Power Grid in terms of ON/OFF sequencing and noise injection due to it. This work explains the state of art here and highlights some of the issues and trade offs using MTCMOS logic. It further suggests a simple approach to quickly access the impact of MTCMOS gates in Power Grid in terms of peak currents and IR drop. Alternatively, the approach suggested also helps in MTCMOS gate optimization. Early leakage optimization overhead can be computed using this approach.

This thesis presents teaching fundamentals of digital logic design and VLSI design for freshmen and even for high school students using e-textiles. This easily grabs attention of students as it is creative and interesting. Using e-textiles to project these concepts would be easily understood by students at young age. This involves stitching electronic circuits on a fabric using basic components like LEDs, push buttons and so on. The functioning of these circuits is programmed in Lilypad Arduino. By using this method, students get exposed to basic electronic concepts at early stage which eventually develops interest towards engineering field.

The design of VLSI electronic circuits can be achieved at many different abstraction levels starting from system behavior to the most detailed, physical layout level. As the number of transistors in VLSI circuits is increasing, the complexity of the design is also increasing, and it is now beyond human ability to manage. Hence CAD (Computer Aided design) or EDA (Electronic Design Automation) tools are involved in the design. EDA or CAD tools automate the design, verification and testing of these VLSI circuits. In today’s market, there are many EDA tools available. However, they are very expensive and require high-performance platforms. One of the key challenges today is to select appropriate CAD or EDA tools which are open-source for academic purposes. This thesis provides a detailed examination of an open-source EDA tool called Electric VLSI Design system. An excellent and efficient CAD tool useful for students and teachers to implement ideas by modifying the source code, Electric fulfills these requirements. This thesis' primary objective is to explain the Electric software features and architecture and to provide various digital and analog designs that are implemented by this software for educational purposes. Since the choice of an EDA tool is based on the efficiency and functions that it can provide, this thesis explains all the analysis and synthesis tools that electric provides and how efficient they are. Hence, this thesis is of benefit for students and teachers that choose Electric as their open-source EDA tool for educational purposes.

Vertical stacking—based on modern manufacturing and integration technologies—of multiple 2D chips enables three-dimensional integrated circuits (3D ICs). This exploitation of the third dimension is generally accepted for aiming at higher packing densities, heterogeneous integration, shorter interconnects, reduced power consumption, increased data bandwidth, and realizing highly-parallel systems in one device. However, the commercial acceptance of 3D ICs is currently behind its expectations, mainly due to challenges regarding manufacturing and integration technologies as well as design automation. This work addresses three selected, practically relevant design challenges: (i) increasing the constrained reusability of proven, reliable 2D intellectual property blocks, (ii) planning different types of (comparatively large) through-silicon vias with focus on their impact on design quality, as well as (iii) structural planning of massively-parallel, 3D-IC-specific interconnect structures during 3D floorplanning. A key concept of this work is to account for interconnect structures and their properties during early design phases in order to support effective and high-quality 3D-IC-design flows. To tackle the above listed challenges, modular design-flow extensions and methodologies have been developed. Experimental investigations reveal the effectiveness and efficiency of the proposed techniques, and provide findings on 3D integration with particular focus on interconnect structures. We suggest consideration of these findings when formulating guidelines for successful 3D-IC design automation. / Dreidimensional integrierte Schaltkreise (3D-ICs) beruhen auf neuartigen Herstellungs- und Integrationstechnologien, wobei vor allem “klassische” 2D-ICs vertikal zu einem neuartigen 3D-System gestapelt werden. Dieser Ansatz zur Erschließung der dritten Dimension im Schaltkreisentwurf ist nach Expertenmeinung dazu geeignet, höhere Integrationsdichten zu erreichen, heterogene Integration zu realisieren, kürzere Verdrahtungswege zu ermöglichen, Leistungsaufnahmen zu reduzieren, Datenübertragungsraten zu erhöhen, sowie hoch-parallele Systeme in einer Baugruppe umzusetzen. Aufgrund von technologischen und entwurfsmethodischen Schwierigkeiten bleibt jedoch bisher die kommerzielle Anwendung von 3D-ICs deutlich hinter den Erwartungen zurück. In dieser Arbeit werden drei ausgewählte, praktisch relevante Problemstellungen der Entwurfsautomatisierung von 3D-ICs bearbeitet: (i) die Verbesserung der (eingeschränkten) Wiederverwendbarkeit von zuverlässigen 2D-Intellectual-Property-Blöcken, (ii) die komplexe Planung von verschiedenartigen, verhältnismäßig großen Through-Silicion Vias unter Beachtung ihres Einflusses auf die Entwurfsqualität, und (iii) die strukturelle Einbindung von massiv-parallelen, 3D-IC-spezifischen Verbindungsstrukturen während der Floorplanning-Phase. Das Ziel dieser Arbeit besteht darin, Verbindungsstrukturen mit deren wesentlichen Eigenschaften bereits in den frühen Phasen des Entwurfsprozesses zu berücksichtigen. Dies begünstigt einen qualitativ hochwertigen Entwurf von 3D-ICs. Die in dieser Arbeit vorgestellten modularen Entwurfsprozess-Erweiterungen bzw. -Methodiken dienen zur effizienten Lösung der oben genannten Problemstellungen. Experimentelle Untersuchungen bestätigen die Wirksamkeit sowie die Effektivität der erarbeiten Methoden. Darüber hinaus liefern sie praktische Erkenntnisse bezüglich der Anwendung von 3D-ICs und der Planung deren Verbindungsstrukturen. Diese Erkenntnisse sind zur Ableitung von Richtlinien für den erfolgreichen Entwurf von 3D-ICs dienlich.

Vertical stacking—based on modern manufacturing and integration technologies—of multiple 2D chips enables three-dimensional integrated circuits (3D ICs). This exploitation of the third dimension is generally accepted for aiming at higher packing densities, heterogeneous integration, shorter interconnects, reduced power consumption, increased data bandwidth, and realizing highly-parallel systems in one device. However, the commercial acceptance of 3D ICs is currently behind its expectations, mainly due to challenges regarding manufacturing and integration technologies as well as design automation. This work addresses three selected, practically relevant design challenges: (i) increasing the constrained reusability of proven, reliable 2D intellectual property blocks, (ii) planning different types of (comparatively large) through-silicon vias with focus on their impact on design quality, as well as (iii) structural planning of massively-parallel, 3D-IC-specific interconnect structures during 3D floorplanning. A key concept of this work is to account for interconnect structures and their properties during early design phases in order to support effective and high-quality 3D-IC-design flows. To tackle the above listed challenges, modular design-flow extensions and methodologies have been developed. Experimental investigations reveal the effectiveness and efficiency of the proposed techniques, and provide findings on 3D integration with particular focus on interconnect structures. We suggest consideration of these findings when formulating guidelines for successful 3D-IC design automation.:1 Introduction 1.1 The 3D Integration Approach for Electronic Circuits 1.2 Technologies for 3D Integrated Circuits 1.3 Design Approaches for 3D Integrated Circuits 2 State of the Art in Design Automation for 3D Integrated Circuits 2.1 Thermal Management 2.2 Partitioning and Floorplanning 2.3 Placement and Routing 2.4 Power and Clock Delivery 2.5 Design Challenges 3 Research Objectives 4 Planning Through-Silicon Via Islands for Block-Level Design Reuse 4.1 Problems for Design Reuse in 3D Integrated Circuits 4.2 Connecting Blocks Using Through-Silicon Via Islands 4.2.1 Problem Formulation and Methodology Overview 4.2.2 Net Clustering 4.2.3 Insertion of Through-Silicon Via Islands 4.2.4 Deadspace Insertion and Redistribution 4.3 Experimental Investigation 4.3.1 Wirelength Estimation 4.3.2 Configuration 4.3.3 Results and Discussion 4.4 Summary and Conclusions 5 Planning Through-Silicon Vias for Design Optimization 5.1 Deadspace Requirements for Optimized Planning of Through-Silicon Vias 5.2 Multiobjective Design Optimization of 3D Integrated Circuits 5.2.1 Methodology Overview and Configuration 5.2.2 Techniques for Deadspace Optimization 5.2.3 Design-Quality Analysis 5.2.4 Planning Different Types of Through-Silicon Vias 5.3 Experimental Investigation 5.3.1 Configuration 5.3.2 Results and Discussion 5.4 Summary and Conclusions 6 3D Floorplanning for Structural Planning of Massive Interconnects 6.1 Block Alignment for Interconnects Planning in 3D Integrated Circuits 6.2 Corner Block List Extended for Block Alignment 6.2.1 Alignment Encoding 6.2.2 Layout Generation: Block Placement and Alignment 6.3 3D Floorplanning Methodology 6.3.1 Optimization Criteria and Phases and Related Cost Models 6.3.2 Fast Thermal Analysis 6.3.3 Layout Operations 6.3.4 Adaptive Optimization Schedule 6.4 Experimental Investigation 6.4.1 Configuration 6.4.2 Results and Discussion 6.5 Summary and Conclusions 7 Research Summary, Conclusions, and Outlook Dissertation Theses Notation Glossary Bibliography / Dreidimensional integrierte Schaltkreise (3D-ICs) beruhen auf neuartigen Herstellungs- und Integrationstechnologien, wobei vor allem “klassische” 2D-ICs vertikal zu einem neuartigen 3D-System gestapelt werden. Dieser Ansatz zur Erschließung der dritten Dimension im Schaltkreisentwurf ist nach Expertenmeinung dazu geeignet, höhere Integrationsdichten zu erreichen, heterogene Integration zu realisieren, kürzere Verdrahtungswege zu ermöglichen, Leistungsaufnahmen zu reduzieren, Datenübertragungsraten zu erhöhen, sowie hoch-parallele Systeme in einer Baugruppe umzusetzen. Aufgrund von technologischen und entwurfsmethodischen Schwierigkeiten bleibt jedoch bisher die kommerzielle Anwendung von 3D-ICs deutlich hinter den Erwartungen zurück. In dieser Arbeit werden drei ausgewählte, praktisch relevante Problemstellungen der Entwurfsautomatisierung von 3D-ICs bearbeitet: (i) die Verbesserung der (eingeschränkten) Wiederverwendbarkeit von zuverlässigen 2D-Intellectual-Property-Blöcken, (ii) die komplexe Planung von verschiedenartigen, verhältnismäßig großen Through-Silicion Vias unter Beachtung ihres Einflusses auf die Entwurfsqualität, und (iii) die strukturelle Einbindung von massiv-parallelen, 3D-IC-spezifischen Verbindungsstrukturen während der Floorplanning-Phase. Das Ziel dieser Arbeit besteht darin, Verbindungsstrukturen mit deren wesentlichen Eigenschaften bereits in den frühen Phasen des Entwurfsprozesses zu berücksichtigen. Dies begünstigt einen qualitativ hochwertigen Entwurf von 3D-ICs. Die in dieser Arbeit vorgestellten modularen Entwurfsprozess-Erweiterungen bzw. -Methodiken dienen zur effizienten Lösung der oben genannten Problemstellungen. Experimentelle Untersuchungen bestätigen die Wirksamkeit sowie die Effektivität der erarbeiten Methoden. Darüber hinaus liefern sie praktische Erkenntnisse bezüglich der Anwendung von 3D-ICs und der Planung deren Verbindungsstrukturen. Diese Erkenntnisse sind zur Ableitung von Richtlinien für den erfolgreichen Entwurf von 3D-ICs dienlich.:1 Introduction 1.1 The 3D Integration Approach for Electronic Circuits 1.2 Technologies for 3D Integrated Circuits 1.3 Design Approaches for 3D Integrated Circuits 2 State of the Art in Design Automation for 3D Integrated Circuits 2.1 Thermal Management 2.2 Partitioning and Floorplanning 2.3 Placement and Routing 2.4 Power and Clock Delivery 2.5 Design Challenges 3 Research Objectives 4 Planning Through-Silicon Via Islands for Block-Level Design Reuse 4.1 Problems for Design Reuse in 3D Integrated Circuits 4.2 Connecting Blocks Using Through-Silicon Via Islands 4.2.1 Problem Formulation and Methodology Overview 4.2.2 Net Clustering 4.2.3 Insertion of Through-Silicon Via Islands 4.2.4 Deadspace Insertion and Redistribution 4.3 Experimental Investigation 4.3.1 Wirelength Estimation 4.3.2 Configuration 4.3.3 Results and Discussion 4.4 Summary and Conclusions 5 Planning Through-Silicon Vias for Design Optimization 5.1 Deadspace Requirements for Optimized Planning of Through-Silicon Vias 5.2 Multiobjective Design Optimization of 3D Integrated Circuits 5.2.1 Methodology Overview and Configuration 5.2.2 Techniques for Deadspace Optimization 5.2.3 Design-Quality Analysis 5.2.4 Planning Different Types of Through-Silicon Vias 5.3 Experimental Investigation 5.3.1 Configuration 5.3.2 Results and Discussion 5.4 Summary and Conclusions 6 3D Floorplanning for Structural Planning of Massive Interconnects 6.1 Block Alignment for Interconnects Planning in 3D Integrated Circuits 6.2 Corner Block List Extended for Block Alignment 6.2.1 Alignment Encoding 6.2.2 Layout Generation: Block Placement and Alignment 6.3 3D Floorplanning Methodology 6.3.1 Optimization Criteria and Phases and Related Cost Models 6.3.2 Fast Thermal Analysis 6.3.3 Layout Operations 6.3.4 Adaptive Optimization Schedule 6.4 Experimental Investigation 6.4.1 Configuration 6.4.2 Results and Discussion 6.5 Summary and Conclusions 7 Research Summary, Conclusions, and Outlook Dissertation Theses Notation Glossary Bibliography