Cold-flow tests were performed using a simulated Air Augmented Rocket (AAR) operating as a mixer-ejector in order to investigate the effects of varied primary nozzle lip thickness on mixing and entrainment. The simulated primary rocket ejector was supplied with nitrogen at a maximum chamber stagnation pressure of 1712 psi, and maximum flow rate of 1.67 lbm/s. Secondary air was entrained from a plenum, producing pressures as low as 6.8 psi and yielding maximum stagnation pressure ratios as high as 160. The primary ejector nozzles each had an area ratio of approximately 20, yielding average primary exit Mach numbers between 4.34 and 4.57. The primary flow was ejected into an 18.75 inch-long mixing duct with a rectangular cross-sectional area of 2.10 in2. The secondary flow was entrained into the mixing duct through a total cross section of 0.94 in2. Two mixing duct configurations were used, one with plexiglass upper and lower surfaces for flow visualization and one with pressure ports along the lower surface for primary plume measurements. Shadowgraph images were used to characterize the mixing duct flow field, while pressure and temperature instrumentation allowed for calculation of various ejector performance characteristics. Experimentally-calculated performance characteristics were compared to inviscid theoretical predictions. Varying degrees of flow field asymmetry were observed with each nozzle. Test repeatability was found to be excellent for all nozzles. Several distinct phenomena were observed in both the primary plume and secondary streams. The duration of secondary flow choking was found to be inversely proportional to nozzle lip thickness, due to the primary plume being physically closer to the secondary flow with a thinner nozzle lip. This indicated that the ejector’s ability to choke the secondary flow is primarily an inviscid phenomenon. Secondary flow blockage was demonstrated in two consecutive tests using the thickest nozzle lip. Only the left secondary duct became blocked in each case. Blockage was only demonstrated in the centerline pressure configuration, so no visual evidence was able to support the blocked flow theory. At every pressure ratio, entrainment ratio was shown to increase with nozzle lip thickness. The original conical nozzle produced the largest level of entrainment, indicating that the angle of primary flow impingement was the largest contributing factor to secondary entrainment. The increase in efficiency resulting from a bell-mouth nozzle was less than the increase in entrainment efficiency of a conical nozzle, indicating that the conical design was more efficient overall for air augmented rocket applications.

This study highlights the aeroelastic behavior of very flexible truss-braced wing (TBW) aircraft designs obtained through a multidisciplinary design optimization (MDO) framework. Several improvements to previous analysis methods were developed and validated. Firstly, a flutter constraint was developed and the effects of the constraint on the MDO of TBW transport aircraft for both medium-range and long-range missions were studied while minimizing the take-off gross weight (TOGW) and the fuel burn as the objective functions. Results show that when the flutter constraint is applied at 1.15 times the dive speed, it imposes a 1.5% penalty on the take-off weight and a 5% penalty on the fuel consumption while minimizing these two objective functions for the medium-range mission. For the long-range mission, the penalties imposed by the similar constraint on the minimum TOGW and minimum fuel burn designs are 3.5% and 7.5%, respectively. Importantly, the resulting TBW designs are still superior to equivalent cantilever designs for both of the missions as they have both lower TOGW and fuel burn. However, a relaxed flutter constraint applied at 1.05 times the dive speed can restrict the penalty on the TOGW to only 0.3% and that on the fuel burn to 2% for minimizing both the objectives, for the medium-range mission. For the long-range mission, a similar relaxed constraint can reduce the penalty on fuel burn to 2.9%. These observations suggest further investigation into active flutter suppression mechanisms for the TBW aircraft to further reduce either the TOGW or the fuel burn. Secondly, the effects of a variable-geometry raked wingtip (VGRWT) on the maneuverability and aeroelastic behavior of passenger aircraft with very flexible truss-braced wings (TBW) were investigated. These TBW designs obtained from the MDO environment while minimizing fuel burn resemble a Boeing 777-200 Long Range (LR) aircraft both in terms of flight mission and aircraft configuration. The VGRWT can sweep forward and aft relative to the wing with the aid of a Novel Control Effector (NCE) mechanism. Results show that the VGRWT can be swept judiciously to alter the bending-torsion coupling and the movement of the center of pressure of wing. Such behavior of the VGRWT is applied to both achieve the required roll control as well as to increase flutter speed, and thus, enable the operation of TBW configurations which have up to 10% lower fuel burn than comparable optimized cantilever wing designs. Finally, a transonic aeroelastic analysis tool was developed which can be used for conceptual design in an MDO environment. Routine transonic aeroelastic analysis require expensive CFD simulations, hence they cannot be performed in an MDO environment. The present approach utilizes the results of a companion study of CFD simulations performed offline for the steady Reynolds Averaged Navier Stokes equations for a variety of airfoil parameters. The CFD results are used to develop a response surface which can be used in the MDO environment to perform a Leishman-Beddoes (LB) indicial functions based flutter analysis. A reduced-order model (ROM) is also developed for the unsteady aerodynamic system. Validation of the strip theory based aeroelastic analysis with LB unsteady aerodynamics and the computational efficiency and accuracy of the ROM is demonstrated. Finally, transonic aeroelastic analysis of a TBW aircraft designed for the medium-range flight mission similar to a Boeing 737 next generation (NG) with a cruise Mach number of 0.8 is presented. The results show the potential of the present approach to perform a more accurate, yet inexpensive, flutter analysis for MDO studies of transonic transport aircraft which are expected to undergo flutter at transonic conditions. / Ph. D.

The purpose of this thesis is to design the key parameters of the high-powered Walkel engine and to design a chamber side on the base of computed parameters so that it enables variable change of the intake and exhaust port geometry. Consequently, to carry out a flow simulation in both ports in designed chamber side in order to find out its flow character and geometry change reaction.

<p dir="ltr">Rotating detonation combustors are a developing technology with the potential to successfully integrate pressure gain combustion in to modern propulsion devices. Utilization of propagating detonation waves could increase combustion cycle efficiency and reduce combustor size, resulting in an overall increase in system range or payload-carrying capabilities. However, the sensitivity of rotating detonation combustor operation and performance to geometric features, such as injector configuration or chamber length, still needs to be characterized over a wide range of operating conditions. In addition, the hardware configuration that promotes easy ignition into a coherent detonation operating mode does not always maximize combustor performance, especially at low-loss conditions where feedback between chamber and manifold dynamics can exist. Therefore, a rotating detonation combustor with continuously variable geometry capabilities was designed in order to continuously vary any number of hardware design parameters during combustor testing. Not only does the variable geometry combustor enable rapid characterization of operability sensitivity with minimal hardware swaps, it also enables exploration of hysteresis in performance as the combustor is ignited in one configuration and transitioned to a different geometry while maintaining detonative operation.</p><p dir="ltr">The operability of the variable geometry rotating detonation combustor was first characterized with variable fuel injector location. Higher wave speeds were observed at injector locations closest to the oxidizer throat, with decreased wave speed and eventual transition to deflagrative operation occurring at locations farther downstream due to increasing momentum flux ratio. Variation in fuel injection location induced bifurcations in the number of waves, resulting in corresponding changes in wave speed and gross thrust. Hysteresis was observed in these quantities as the direction of injector translation was reversed. Active translation promoted detonative operation of the experiment at conditions and configurations that hitherto operated only in a deflagrative mode with fixed combustor geometry. </p><p dir="ltr">Sensitivity of rotating detonation combustor operation and performance to oxidizer injector pressure drop was characterized using continuous variation of the injector area during combustor operation. Propulsive performance of the combustor was evaluated using thrust and equivalent available pressure, relating them back to reactant supply pressures for assessment of combustor pressure gain. An effective reactant supply pressure was developed in order to combine contributions of both fuel and oxidizer manifold pressures to the total pressure of the system so that pressure gain could be accurately calculated. Pressure gain increased during a test as oxidizer injector area was increased and the corresponding manifold pressure was decreased. At larger injector areas, pressure gain decreased as the operating mode of the combustor transitioned from detonation to deflagration, concomitant with reduction of gross thrust. Modeling of injector recovery time revealed that the injector operated in both choked and unchoked regimes, which was used to explain detonation wave number transitions in the experiment. A broadened range of detonative operability enabled by active variation of combustor geometry resulted in higher performance with lower injector pressure drop.</p><p dir="ltr">Sensitivity of rotating detonation combustor operation and performance to combustor chamber length was characterized using continuous variation of the chamber length during combustor operation. Specific impulse of the combustor remained relatively constant as chamber length was decreased from its maximum values, proving the practicality of efficient packaging for rotating detonation combustors. A limiting chamber length at which combustion could not longer be supported within the chamber was found to exist for every operating condition, resulting in flame blow-out and performance degradation. Modeling of detonation fill height revealed that relatively low specific impulse measurements could be attributed to unburned reactants exiting the chamber, and a more efficient use of reactants was potentially the cause for improved performance at higher mass flow rates as detonation wave number increased and reactant residence time decreased.</p><p dir="ltr">This experiment and the associated analysis has helped further characterize rotating detonation combustor sensitivity to hardware design parameters. The continuously variable geometry capabilities enabled precise identification of geometric parameters that resulted in operating mode transitions. Analysis and modeling of the flow processes within the injector and chamber were used to help explain why these mode transitions occurred, and can be used for future rotating detonation combustor development.</p>

No description available.

No description available.

The choice of technology for automotive actuators is driven by the need of high power to size ratio. In general, electro-pneumatic actuators are preferred for application around the engine as they are compact, powerful and require simple controlling devices. Specially, Variable Geometry Turbochargers (VGTs) are almost always controlled with electro-pneumatic actuators. This is a challenging application because the VGT is an important part of the engine air path and the latter is responsible for intake and exhaust air quality and exhaust emissions control. With government regulations on vehicle pollutant emissions getting stringent by the year, VGT control requirements have also increased. These regulations and requirements can only be fulfilled with precise dynamic control of the VGT through its actuator. The demands on actuator control include robustness against uncertainty in operating conditions, fast and smooth positioning without vibration, limited number of measurements. Added constraints such as nonlinear dynamic behavior of the actuator, friction and varying aerodynamic forces in the VGT render classical control methods ineffective. These are the main problems that form the core of this thesis.In this work, we have addressed the above mentioned problems, using model based control complemented with robust control methods to overcome operational uncertainties and parametric variations. In the first step, a detailed physical model of an electro-pneumatic actuator has been developed; taking into account the nonlinear characteristics originating from air compressibility and friction. Means to compensate for aerodynamic force have been studied and implemented in the next step. These include model parametric adaptation and one dimensional CFD (Computational Fluid Dynamics) modeling. The complete model has been experimentally validated and a sensitivity analysis has been conducted to identify the parameters which have the greatest impact upon the actuator's behavior. The detailed simulation model has then been simplified to make it suitable for control purposes while keeping its essential behavioral characteristics (i.e. transients and dynamics). Next, robust controllers have been developed around the model for the control objective of accurate actuator positioning in presence of operational uncertainty. An important constraint in commercial actuators is that they provide output feedback only, as they are only equipped with low-cost position sensors. This hurdle has been overcome by introducing observers in the control loop, which estimate other system states from the output feedback. The estimation and control algorithms have been validated in simulation and experimentally on diesel engine test benches.

The goal is to measure the temperature of the turbocharger after engine shutdown.Measurements wants to show the need to keep a car engine to cool after a heavier burden on the idle speed. It would also prevent possible disruptions turbocharger. The paper also deals with the problems, construction and basic principles of operation of the turbocharger

The ever increasing demands on today's engine performance and emissions control is forcing the automotive industry to make use of innovative solutions. One of these is to apply the technology of VNT turbos on commercial petrol vehicles. When using a VNT turbo, the aspect ratio of the turbine can be altered while driving to suit the current operating window. In order to actually gain performance while using a VNT, the vanes have to be properly controlled using a suitable control strategy. In this project, direct collocation have been utilized through the usage of YOP which is an adaptation of CasADi in MATLAB to solve non-linear optimization problems. Comprehensive models of the turbocharger and the cylinders have been built and validated to properly represent a VEP4 LP engine from AUROBAY. The models are implemented in YOP to create and simulate different OCPs using the turbo speed as state and position of the vanes as control signal. With this model in YOP together with the air mass flow per second as reference, a good reference following together with decent values for relevant parameters can be accomplished. Other objective functions such as minimum time and maximal volumetric efficiency are also investigated in the project which yield likewise results. From the results it can be concluded that this type of model and control strategy can be used with success when studying optimal control of a VNT turbo.

Les actionneurs électropneumatiques sont très utilisés dans l'industrie automobile car ils offrent de grands avantages, en termes d'encombrement, de puissance élevée et de simplicité de commande. Ces actionneurs sont utilisés plus particulièrement pour le contrôle des Turbocompresseurs à Géométrie Variable (TGV). Le TGV joue un rôle très important dans les performances de la boucle d'air du moteur, en particulier sur la qualité de l'air à l'admission et à l'échappement. Les nouvelles réglementations gouvernementales concernant les émissions polluantes des véhicules ont poussé les équipementiers automobiles à s'intéresser davantage au contrôle du Turbocompresseur à Géométrie Variable. Ces exigences ne peuvent pas être realisées à travers des techniques classiques de contrôle de type PID. En effet, le contrôle doit tenir compte de la complexité du modèle et de ses incertitudes ainsi que des exigences en termes de performances statiques et dynamiques et du nombre limité de mesures. De plus, il faut également tenir compte des conditions agressives dans lesquelles travaillent l'actionneur, notamment la température, les forces de frottement et les forces aérodynamiques à l'entrée du turbo. Dans le cadre de cette thèse, ce sont tous ces aspects qui ont motivé notre travail de modélisation et de commande robuste de l'actionneur électropneumatique du turbo. Dans un premier temps, nous avons établi un modèle de simulation de l'actionneur. Nous avons commencé par élaborer un modèle physique détaillé de l'actionneur, en prenant en compte les caractéristiques non linéaires provenant de la compressibilité de l'air et du frottement. Ensuite, deux modèles des forces aérodynamiques qui agissement sur l'actionneur ont été proposés. Le modèle global de l'actionneur a été validé expérimentalement et une analyse de sensibilité expérimentale a été menée sur plusieurs actionneurs afin d'identifier les paramètres ayant le plus d'impact sur les performances de l'actionneur. Dans un second temps, nous avons proposé une simplification du modèle obtenu dans le but de le rendre utilisable pour le contrôle, tout en préservant ses caractéristiques statiques et dynamiques. Enfin, nous nous sommes intéressés à la résolution du problème de commande robuste par retour de sortie de l'actionneur. Les algorithmes de contrôle et d'estimation élaborés ont été validés d'abord par des simulations, puis expérimentalement sur un banc d'essai moteur. / The choice of technology for automotive actuators is driven by the need of high power to size ratio. In general, electro-pneumatic actuators are preferred for application around the engine as they are compact, powerful and require simple controlling devices. Specially, Variable Geometry Turbochargers (VGTs) are almost always controlled with electro-pneumatic actuators. This is a challenging application because the VGT is an important part of the engine air path and the latter is responsible for intake and exhaust air quality and exhaust emissions control. With government regulations on vehicle pollutant emissions getting stringent by the year, VGT control requirements have also increased. These regulations and requirements can only be fulfilled with precise dynamic control of the VGT through its actuator. The demands on actuator control include robustness against uncertainty in operating conditions, fast and smooth positioning without vibration, limited number of measurements. Added constraints such as nonlinear dynamic behavior of the actuator, friction and varying aerodynamic forces in the VGT render classical control methods ineffective. These are the main problems that form the core of this thesis.In this work, we have addressed the above mentioned problems, using model based control complemented with robust control methods to overcome operational uncertainties and parametric variations. In the first step, a detailed physical model of an electro-pneumatic actuator has been developed; taking into account the nonlinear characteristics originating from air compressibility and friction. Means to compensate for aerodynamic force have been studied and implemented in the next step. These include model parametric adaptation and one dimensional CFD (Computational Fluid Dynamics) modeling. The complete model has been experimentally validated and a sensitivity analysis has been conducted to identify the parameters which have the greatest impact upon the actuator's behavior. The detailed simulation model has then been simplified to make it suitable for control purposes while keeping its essential behavioral characteristics (i.e. transients and dynamics). Next, robust controllers have been developed around the model for the control objective of accurate actuator positioning in presence of operational uncertainty. An important constraint in commercial actuators is that they provide output feedback only, as they are only equipped with low-cost position sensors. This hurdle has been overcome by introducing observers in the control loop, which estimate other system states from the output feedback. The estimation and control algorithms have been validated in simulation and experimentally on diesel engine test benches.