Peak electricity demand in South Africa will exceed the available operational generation capacity in 2007. The state utility Eskom is addressing this challenge, inter aha, with the implementation of the Demand-side Management (DSM) initiative. The aim of DSM is to defer the building of additional power stations by modifying the end-user pattern to reduce electrical load during the morning and evening peaks. At the end of 2005 the DSM programme has only achieved 30°/o of its target. Some of the biggest problems are the lack of knowledge on how to perform ESCO audits and availability of tools and procedures to enable Energy Service Companies (ESCOs) to evaluate DSM potential. Studies in South Africa have shown that 20°/o of the total municipal energy is utilised in commercial buildings. Additional investigations have shown that in the commercial sector approximately 50% of energy is used for air conditioning. Energy savings of around 30% can be realised through improved management procedures and retrofit projects of HVAC systems of existing buildings. Telecommunication companies own and operate a large portfolio of diverse buildings. It was shown that these buildings are very inefficient in terms of energy usage. Performing ESCO analyses on these building portfolios present huge savings opportunities for the building owners as well as load reduction opportunities to help meet DSM targets. ESCOs however face major problems in evaluating DSM projects on telecommunication facilities. Some of these problems are: time to perform the ESCO audits on such a large portfolio of buildings; skill levels of available personnel; lack of experience and structured audit process; availability of information; data capturing of information; determining the impact of the retrofits and calculating the savings and financial benefits of retrofits. Obtaining approval for DSM projects is also a lengthy process. Smaller ESCOs cannot afford to commit resources to ESCO investigations only to recover their investment after project approval. Having an ESCO procedure that will speed up the audit process will help the ESCO to minimise resources that need to be committed to these investigations. Having a tested and reliable ESCO procedure will also help Eskom since they will receive more and better quality DSM proposals. A new ESCO procedure for telecommunications facilities was developed. The primary requirements for the new ESCO procedure are that it should be simple, stable, fast and accurate. This procedure is evaluated against the known energy management opportunities in telecommunication facilities. Some of the benefits of the new ESCO procedure are: time taken to perform ESCO analysis on all types of buildings is drastically reduced; lower qualified personnel can be used to perform the ESCO analysis; any type of HVAC system configuration can be accommodated; new data capturing procedures ensure that only essential data is captured; integrated simulation software is used that can easy and accurately simulate the building operations and retrofits on a building; retrofit options suitable for telecommunication facilities are identified; contribution to the DSM programme is evaluated; financial evaluation of the retrofits and feasibility for DSM funding and results are integrated into a standardised reporting format. The new ESCO procedure was implemented on several case studies within the telecommunication infrastructure. Five different types of buildings were selected to implement the ESCO procedure. Each step of the procedure was evaluated and tested against the requirements of the new ESCO procedure. It was proven through implementation that the new ESCO procedure is successful in solving the unique problems in performing ESCO analyses for telecommunications facilities. Valuable insight into the problems that can occur during the ESCO process was highlighted, and recommendation for future work was presented. / Thesis (Ph.D. (Electrical Engineering))--North-West University, Potchefstroom Campus, 2006.

Thesis (Ph.D. (Electrical Engineering))--North-West University, Potchefstroom Campus, 2006.

Peak electricity demand in South Africa will exceed the available operational generation capacity in 2007. The state utility Eskom is addressing this challenge, inter aha, with the implementation of the Demand-side Management (DSM) initiative. The aim of DSM is to defer the building of additional power stations by modifying the end-user pattern to reduce electrical load during the morning and evening peaks. At the end of 2005 the DSM programme has only achieved 30°/o of its target. Some of the biggest problems are the lack of knowledge on how to perform ESCO audits and availability of tools and procedures to enable Energy Service Companies (ESCOs) to evaluate DSM potential. Studies in South Africa have shown that 20°/o of the total municipal energy is utilised in commercial buildings. Additional investigations have shown that in the commercial sector approximately 50% of energy is used for air conditioning. Energy savings of around 30% can be realised through improved management procedures and retrofit projects of HVAC systems of existing buildings. Telecommunication companies own and operate a large portfolio of diverse buildings. It was shown that these buildings are very inefficient in terms of energy usage. Performing ESCO analyses on these building portfolios present huge savings opportunities for the building owners as well as load reduction opportunities to help meet DSM targets. ESCOs however face major problems in evaluating DSM projects on telecommunication facilities. Some of these problems are: time to perform the ESCO audits on such a large portfolio of buildings; skill levels of available personnel; lack of experience and structured audit process; availability of information; data capturing of information; determining the impact of the retrofits and calculating the savings and financial benefits of retrofits. Obtaining approval for DSM projects is also a lengthy process. Smaller ESCOs cannot afford to commit resources to ESCO investigations only to recover their investment after project approval. Having an ESCO procedure that will speed up the audit process will help the ESCO to minimise resources that need to be committed to these investigations. Having a tested and reliable ESCO procedure will also help Eskom since they will receive more and better quality DSM proposals. A new ESCO procedure for telecommunications facilities was developed. The primary requirements for the new ESCO procedure are that it should be simple, stable, fast and accurate. This procedure is evaluated against the known energy management opportunities in telecommunication facilities. Some of the benefits of the new ESCO procedure are: time taken to perform ESCO analysis on all types of buildings is drastically reduced; lower qualified personnel can be used to perform the ESCO analysis; any type of HVAC system configuration can be accommodated; new data capturing procedures ensure that only essential data is captured; integrated simulation software is used that can easy and accurately simulate the building operations and retrofits on a building; retrofit options suitable for telecommunication facilities are identified; contribution to the DSM programme is evaluated; financial evaluation of the retrofits and feasibility for DSM funding and results are integrated into a standardised reporting format. The new ESCO procedure was implemented on several case studies within the telecommunication infrastructure. Five different types of buildings were selected to implement the ESCO procedure. Each step of the procedure was evaluated and tested against the requirements of the new ESCO procedure. It was proven through implementation that the new ESCO procedure is successful in solving the unique problems in performing ESCO analyses for telecommunications facilities. Valuable insight into the problems that can occur during the ESCO process was highlighted, and recommendation for future work was presented. / Thesis (Ph.D. (Electrical Engineering))--North-West University, Potchefstroom Campus, 2006.

This thesis considers the development of a Hammerstein-bilinear approach to non-linear systems modelling, analysis and control systems design, which builds on and extends the applicability of an existing bilinear approach. The underlying idea of the Hammerstein-bilinear approach is to use the Hammerstein-bilinear system models to capture various physical phenomena of interest and subsequently use these for model based control system designs with the premise being that of achieving enhanced control performance. The advantage of the Hammerstein-bilinear approach is that the well-structured system models allow techniques that have been originally developed for linear systems to be extended and applied, while retaining moderate complexity of the corresponding system identification schemes and nonlinear model based control designs. In recognition of the need to be able to identify the Hammerstein-bilinear models a unified suite of algorithms, being the extensions to the simplified refined instrumental variable method for parameter estimation of linear transfer function models is proposed. These algorithms are able to operate in both the continuous-time and discrete-time domains to reflect the requirements of the intended purposes of the identified models with the emphasis being placed on straightforward applicability of the developed algorithms and recognising the need to be able to operate under realistic practical system identification scenarios. Moreover, the proposed algorithms are also applicable to parameter estimation of Hammerstein and bilinear models, which are special cases of the wider Hammerstein-bilinear model class. The Hammerstein-bilinear approach has been applied to an industrial heating, ventilation and air conditioning (HVAC) system, which has also been the underlying application addressed in this thesis. A unique set of dynamic control design purpose oriented air temperature and humidity Hammerstein-bilinear models of an environmentally controlled clear room manufacturing zone has been identified. The greater insights afforded by the knowledge of the system nonlinearities then allow for enhanced control tuning of the associated commercial HVAC control system leading to an improved overall control performance.

Em pauta já há algum tempo, os impactos ambientais, possivelmente gerados pela ação humana, são cada vez mais discutidos e estudados. A busca por um desenvolvimento sustentável e formas mais eficientes do consumo de energia é abordada frequentemente. No Brasil, os edifícios comerciais e públicos apresentam alta demanda de energia elétrica e os sistemas de condicionamento de ar são responsáveis por uma parcela relevante do consumo no país. Para mitigar esse consumo, o sistema de ar condicionado distribuído pelo piso tem sido proposto como uma solução, pois este é intrinsecamente mais eficiente que o sistema de ar condicionado convencional, com distribuição de ar pelo teto. O presente trabalho tem como propósito identificar o potencial de economia de energia de um sistema de condicionamento de ar com distribuição pelo piso em relação a um sistema com distribuição pelo teto, por meio da simulação computacional. Avaliaram-se também o impacto do aumento da temperatura de insuflação e do pé-direito da edificação, além do uso de ciclo economizador (controle entálpico) aplicado aos sistemas na economia de energia. Para a modelagem computacional, realizada pela ferramenta computacional EnergyPlus, tomou-se como referência uma sala de aula que contém um sistema de condicionamento de ar com distribuição pelo piso. O primeiro sistema modelado foi pelo piso, e este serviu como base para a modelagem do sistema pelo teto. Após a criação dos modelos foram executadas as simulações cujos resultados permitiram a comparação entre os consumos de energia de cada um dos sistemas. Em conformidade com a literatura, onde se afirmam que os sistemas com distribuição de ar pelo piso são mais eficientes que os convencionais (distribuição de ar pelo teto), este trabalho também concluiu que este sistema é mais eficiente, apresentando um indicador de economia de energia da ordem de 33%, para a condição: pé-direito de 3,50 m; temperatura de insuflação de 19 °C; e controle entálpico. Os resultados desta pesquisa indicam ainda que a utilização do controle entálpico tem maior influência na economia de energia se comparada ao aumento da temperatura de insuflação ou do pé-direito. / On the agenda for some time, the environmental impacts, possibly generated by human action, are increasingly discussed and studied. The demand for sustainable development and more efficient ways of energy consumption is often addressed. In Brazil, commercial and public buildings have high demand for electricity and air conditioning systems are responsible for a significant portion of this consumption in the country. The underfloor air conditioning system has been proposed as a solution to mitigate such consumption because it is intrinsically more efficient than the ceiling-based air conditioning system. The present work aims to identify the energy saving potential of an air conditioning system with underfloor air distribution comparatively to a system with ceiling air distribution, through computational simulation. Also, the impact of increased supply air temperature and the floor to ceiling height, and the use of the economizer cycle (enthalpy control) was evaluated. For the computational modeling, carried out by the EnergyPlus computational tool, a classroom that contains an air conditioning system with floor distribution was used as reference. The first modeled air distribution system was the underfloor air distribution system, and this served as a basis for the modeling of the ceiling air distribution system. After performing the models, the simulations were carried out, whose results allowed the comparison the energy consumptions between the two systems. According to the literature, where it is stated that the systems with underfloor air distribution are more efficient than the conventional ones (ceiling air distribution), this work also concludes that the system with underfloor air distribution is more efficient, presenting an energy saving indicator around 33%, for the following condition: floor to ceiling height of 3.50 m; supply air temperature of 19 ° C; and enthalpy control. The results of this research also indicate that the use of the enthalpy control has a greater influence on the energy savings compared to the increase of the supply air temperature or the floor to ceiling height.

Noise control in the heating, ventilation and air-conditioning (HVAC) systems is one of the critical design parameters in measuring the occupant comfort. The noise generated by air-handling units propagates through the ducts in the axial as well as transverse direction. Noise radiated in the transverse direction from the duct walls excited by the internal sound field is called the breakout noise. An analytical formulation has been developed in this thesis in order to predict the breakout noise by incorporating three-dimensional effects along with the acoustical and structural wave coupling phenomena. The first step in the breakout noise prediction is to calculate the interior acoustic response and flexural vibration displacement of the compliant walls. Dynamic interaction between the internal acoustic subsystem and flexible structural subsystem has been expressed in terms of the modal characteristics of the uncoupled response of the acoustic and structural sub-systems. Solutions of the inhomogeneous wave equation are rearranged in terms of impedance and mobility, and the equations describing the complete system are expressed in terms of matrices, which result in a compact matrix formulation. Examples of the formulation are a rectangular cavity with one flexible wall and a rectangular cavity with four-flexible walls. The formulation is modified to incorporate complex boundary conditions by means of appropriate Green’s functions. It is implemented for flexible wall duct using the modified cavity Green’s function. Another objective of the present investigation is to understand the coupling phenomenon and its effect on the compliant wall vibration displacement. The developed three-dimensional analytical analysis of the breakout noise is convenient to implement on the computer, and also to extend the sub-system level model to the system level model in order to analyze a complex acoustic-structural system for the breakout noise problem. The extent of coupling is calculated using a transfer factor based on the uncoupled natural frequencies of the acoustic and structural subsystems. It is observed from the free vibration analysis that a coupling between the cavity and the flexible panel exists in the vicinity of an uncoupled acoustic natural frequency. If a strong coupling occurs between an acoustic mode and a panel mode, then damping of structural subsystem would control it. The cavity volume changes stiffness of the panel, which in turn affects noise radiation in the stiffness-controlled region. The second step is to calculate the sound power radiated from complaint wall. The wall vibration velocity is a linear combination of the uncoupled flexural modes of the structural subsystem. It is substituted into the Rayleigh integral and Kirchhoff– Helmholtz (KH) integral formulation to predict the sound pressure radiated by the vibrating duct wall. The radiated sound power can be obtained by integrating the acoustic intensity over the surface of the flexible duct wall making use of appropriate expressions for radiation impedance. The radiation impedance terms involve a quadruple integral. Evaluation of this integral is quite complex and poses formidable computational challenges. These have been overcome by means of a co-ordinate transformation. Sound power radiation from flexible walls of the plenum and duct walls has been calculated using an equivalent plate model. Analytical results are corroborated with numerical models. The second part of thesis deals with a one-dimensional model to predict the breakout noise from a thin rectangular duct with different end conditions like anechoic termination, rigid-end termination, and the open-end termination. This model incorporates acoustic reflection effects in the duct internal sound field by using standing wave pattern by means of the transfer matrix approach. A one-dimensional prediction method based on the four-pole parameters has been developed to evaluate the lagged duct performance in terms of the breakout noise reduction. Radiation impedance of a duct is calculated by three different methods: (i) finite line source model (ii) finite cylinder model, and (iii) equivalent plate model based on fundamental bending mode of the duct. It is observed that the proposed model that uses the equivalent plate model for the lagged duct and the line source model for the bare duct is appropriate to predict the transverse insertion loss of the lagging, particularly at the lower frequencies that are of primary interest for reducing the breakout noise of rectangular ducts. The bare duct breakout noise results are compared with those of the corresponding 3-D analytical models. It shows that the one-dimensional model captures the overall mean pattern of breakout noise very well. The third part of the thesis examines the internal acoustic field and thence the transmission loss (TL) of a rectangular expansion chamber, the inlet and outlet of which are situated at arbitrary locations of the chamber; i.e., the sidewall or the face of the chamber. The four-pole parameters have been expressed in terms of an appropriate Green’s function of a rectangular cavity with homogeneous boundary conditions. A transfer matrix formulation has been developed for the yielding-wall rectangular chambers by considering structural-acoustic coupling. It may be combined readily with the transfer matrices of the other constituent elements upstream and downstream in order to compute the overall transmission loss or insertion loss. Wherever applicable, parametric studies have been conducted to evolve the design guidelines for minimizing the breakout noise from the HVAC ducts, plenums and cavities.

Em pauta já há algum tempo, os impactos ambientais, possivelmente gerados pela ação humana, são cada vez mais discutidos e estudados. A busca por um desenvolvimento sustentável e formas mais eficientes do consumo de energia é abordada frequentemente. No Brasil, os edifícios comerciais e públicos apresentam alta demanda de energia elétrica e os sistemas de condicionamento de ar são responsáveis por uma parcela relevante do consumo no país. Para mitigar esse consumo, o sistema de ar condicionado distribuído pelo piso tem sido proposto como uma solução, pois este é intrinsecamente mais eficiente que o sistema de ar condicionado convencional, com distribuição de ar pelo teto. O presente trabalho tem como propósito identificar o potencial de economia de energia de um sistema de condicionamento de ar com distribuição pelo piso em relação a um sistema com distribuição pelo teto, por meio da simulação computacional. Avaliaram-se também o impacto do aumento da temperatura de insuflação e do pé-direito da edificação, além do uso de ciclo economizador (controle entálpico) aplicado aos sistemas na economia de energia. Para a modelagem computacional, realizada pela ferramenta computacional EnergyPlus, tomou-se como referência uma sala de aula que contém um sistema de condicionamento de ar com distribuição pelo piso. O primeiro sistema modelado foi pelo piso, e este serviu como base para a modelagem do sistema pelo teto. Após a criação dos modelos foram executadas as simulações cujos resultados permitiram a comparação entre os consumos de energia de cada um dos sistemas. Em conformidade com a literatura, onde se afirmam que os sistemas com distribuição de ar pelo piso são mais eficientes que os convencionais (distribuição de ar pelo teto), este trabalho também concluiu que este sistema é mais eficiente, apresentando um indicador de economia de energia da ordem de 33%, para a condição: pé-direito de 3,50 m; temperatura de insuflação de 19 °C; e controle entálpico. Os resultados desta pesquisa indicam ainda que a utilização do controle entálpico tem maior influência na economia de energia se comparada ao aumento da temperatura de insuflação ou do pé-direito. / On the agenda for some time, the environmental impacts, possibly generated by human action, are increasingly discussed and studied. The demand for sustainable development and more efficient ways of energy consumption is often addressed. In Brazil, commercial and public buildings have high demand for electricity and air conditioning systems are responsible for a significant portion of this consumption in the country. The underfloor air conditioning system has been proposed as a solution to mitigate such consumption because it is intrinsically more efficient than the ceiling-based air conditioning system. The present work aims to identify the energy saving potential of an air conditioning system with underfloor air distribution comparatively to a system with ceiling air distribution, through computational simulation. Also, the impact of increased supply air temperature and the floor to ceiling height, and the use of the economizer cycle (enthalpy control) was evaluated. For the computational modeling, carried out by the EnergyPlus computational tool, a classroom that contains an air conditioning system with floor distribution was used as reference. The first modeled air distribution system was the underfloor air distribution system, and this served as a basis for the modeling of the ceiling air distribution system. After performing the models, the simulations were carried out, whose results allowed the comparison the energy consumptions between the two systems. According to the literature, where it is stated that the systems with underfloor air distribution are more efficient than the conventional ones (ceiling air distribution), this work also concludes that the system with underfloor air distribution is more efficient, presenting an energy saving indicator around 33%, for the following condition: floor to ceiling height of 3.50 m; supply air temperature of 19 ° C; and enthalpy control. The results of this research also indicate that the use of the enthalpy control has a greater influence on the energy savings compared to the increase of the supply air temperature or the floor to ceiling height.

The South African economy, which is largely based on heavy industry such as minerals extraction and processing, is by nature very energy intensive. Based on the abundance of coal resources, electricity in South Africa remains amongst the cheapest in the world. Whilst the low electricity price has contributed towards a competitive position, it has also meant that our existing electricity supply is often taken for granted. The economic and environmental benefits of energy efficiency have been well documented. Worldwide, nations are beginning to face up to the challenge of sustainable energy - in other words to alter the way that energy is utilised so that social, environmental and economic aims of sustainable development are supported. South Africa as a developing nation recognises the need for energy efficiency, as it is the most cost effective way of meeting the demands of sustainable development. South Africa, with its unique economic, environmental and social challenges, stands to benefit the most from implementing energy efficiency practices. The Energy Efficiency Strategy for South Africa takes its mandate from the South African White Paper on Energy Policy. It is the first consolidated governmental effort geared towards energy efficiency practices throughout South Africa. The strategy allows for the immediate implementation of low-cost and no-cost interventions, as well as those higher-cost measures with short payback periods. An initial target has been set for an across sector energy efficiency improvement of 12% by 2014. Thermal and energy system simulation is globally recognised as one of the most effective and powerful tools to improve overall energy efficiency. However, because of the usual extreme mathematical nature of most simulation algorithms, coupled with the historically academic environment in which most simulation software is developed, valid perceptions exist that system simulation is too time consuming and cumbersome. It is also commonly known that system simulation is only effective in the hands of highly skilled operators, which are specialists in their prospective fields. Through previous work done in the field, and the design of a dynamic thermal and energy system simulation scheme for cross industry applications, it was shown that system simulation has evolved to such an extent that these perceptions are not valid any more. The South African mining and commercial building industries are two of the major consumers of electricity within South Africa. By improving energy efficiency practices within the building and mining industry, large savings can be realised. An extensive investigation of the literature showed that no general suitable computer simulation software for cross industry mining and building thermal and energy system simulation could be found. Because the heating, ventilation and air conditioning (HVAC) of buildings, closely relate to the ventilation and cooling systems of mines, valuable knowledge from this field was used to identify the requirements and specifications for the design of a new single cross industry dynamic integrated thermal and energy system simulation tool. VISUALQEC was designed and implemented to comply with the needs and requirements identified. A new explicit system component model and explicit system simulation engine, combined with a new improved simulation of mass flow through a system procedure, suggested a marked improvement on overall simulation stability, efficiency and speed. The commercial usability of the new simulation tool was verified for building applications by doing an extensive building energy savings audit. The new simulation tool was further verified by simulating the ventilation and cooling (VC) and underground pumping system of a typical South African gold mine. Initial results proved satisfactory but, more case studies to further verify the accuracy of the implemented cross industry thermal and energy system simulation tool are needed. Because of the stable nature of the new VISUALQEC simulation engine, the power of the simulation process can be further extended to the mathematical optimisation of various system variables. In conclusion, this study highlighted the need for new simulation procedures and system designs for the successful implementation and creation of a single dynamic thermal and energy system simulation tool for cross industry applications. South Africa should take full advantage of the power of thermal and energy system simulation towards creating a more energy efficient society. / Thesis (Ph.D. (Mechanical Engineering))--North-West University, Potchefstroom Campus, 2005.

The South African economy, which is largely based on heavy industry such as minerals extraction and processing, is by nature very energy intensive. Based on the abundance of coal resources, electricity in South Africa remains amongst the cheapest in the world. Whilst the low electricity price has contributed towards a competitive position, it has also meant that our existing electricity supply is often taken for granted. The economic and environmental benefits of energy efficiency have been well documented. Worldwide, nations are beginning to face up to the challenge of sustainable energy - in other words to alter the way that energy is utilised so that social, environmental and economic aims of sustainable development are supported. South Africa as a developing nation recognises the need for energy efficiency, as it is the most cost effective way of meeting the demands of sustainable development. South Africa, with its unique economic, environmental and social challenges, stands to benefit the most from implementing energy efficiency practices. The Energy Efficiency Strategy for South Africa takes its mandate from the South African White Paper on Energy Policy. It is the first consolidated governmental effort geared towards energy efficiency practices throughout South Africa. The strategy allows for the immediate implementation of low-cost and no-cost interventions, as well as those higher-cost measures with short payback periods. An initial target has been set for an across sector energy efficiency improvement of 12% by 2014. Thermal and energy system simulation is globally recognised as one of the most effective and powerful tools to improve overall energy efficiency. However, because of the usual extreme mathematical nature of most simulation algorithms, coupled with the historically academic environment in which most simulation software is developed, valid perceptions exist that system simulation is too time consuming and cumbersome. It is also commonly known that system simulation is only effective in the hands of highly skilled operators, which are specialists in their prospective fields. Through previous work done in the field, and the design of a dynamic thermal and energy system simulation scheme for cross industry applications, it was shown that system simulation has evolved to such an extent that these perceptions are not valid any more. The South African mining and commercial building industries are two of the major consumers of electricity within South Africa. By improving energy efficiency practices within the building and mining industry, large savings can be realised. An extensive investigation of the literature showed that no general suitable computer simulation software for cross industry mining and building thermal and energy system simulation could be found. Because the heating, ventilation and air conditioning (HVAC) of buildings, closely relate to the ventilation and cooling systems of mines, valuable knowledge from this field was used to identify the requirements and specifications for the design of a new single cross industry dynamic integrated thermal and energy system simulation tool. VISUALQEC was designed and implemented to comply with the needs and requirements identified. A new explicit system component model and explicit system simulation engine, combined with a new improved simulation of mass flow through a system procedure, suggested a marked improvement on overall simulation stability, efficiency and speed. The commercial usability of the new simulation tool was verified for building applications by doing an extensive building energy savings audit. The new simulation tool was further verified by simulating the ventilation and cooling (VC) and underground pumping system of a typical South African gold mine. Initial results proved satisfactory but, more case studies to further verify the accuracy of the implemented cross industry thermal and energy system simulation tool are needed. Because of the stable nature of the new VISUALQEC simulation engine, the power of the simulation process can be further extended to the mathematical optimisation of various system variables. In conclusion, this study highlighted the need for new simulation procedures and system designs for the successful implementation and creation of a single dynamic thermal and energy system simulation tool for cross industry applications. South Africa should take full advantage of the power of thermal and energy system simulation towards creating a more energy efficient society. / Thesis (Ph.D. (Mechanical Engineering))--North-West University, Potchefstroom Campus, 2005.