Spelling suggestions: "subject:"alibration -- eontrol"" "subject:"alibration -- 7control""
51 |
Transient analysis and vibration suppression of a cracked rotating shaft with ideal and nonideal motor passing through a critical speedSuherman, Surjani 06 June 2008 (has links)
In the first part of this study, the dynamic behavior of a cracked rotating shaft with a rigid disk is analyzed, with an ideal and a nonideal motor, passing through its critical speed. The shaft contains a single transverse crack that is assumed to be either completely open or completely closed at any given time, depending on the curvature of the shaft at the cross section containing the crack. Flexible, damped supports and overhangs with a mass at one end are included. The supports are modeled with elastic springs and dashpots. The influence of gyroscopic moments of the disk (with an ideal motor) is investigated. For a nonideal motor, there is an interaction between the shaft and the motor.
Eccentricity of the disk, gravitational forces, and internal and external damping are included. The equations of motion and boundary conditions are derived by Hamilton's Principle. To eliminate the spatial dependence, the Extended Galerkin Method is applied. Longitudinal vibration, shear deformation and torsional vibration are neglected.
In the second part of this study, the vibration suppression of a cracked, simply supported, rotating shaft with a rigid disk is discussed, with an ideal and a nonideal motor, passing through the critical speed. The use of a flexible internal constraint is introduced to suppress the vibration. By activating this additional internal support, the shaft is prevented from passing its critical speed. Transient motions occur at the time of activation or deactivation of the constraint. The maximum displacement of the shaft during acceleration (run-up) or deceleration (coast-down) can be reduced significantly by appropriate application of this flexible internal support. / Ph. D.
|
52 |
Integrated structural design, vibration control, and aeroelastic tailoring by multiobjective optimizationCanfield, Robert A. 28 July 2008 (has links)
The integrated design of a structure and its control system was treated as a multiobjective optimization problem. Structural mass, a quadratic performance index, and the flutter speed constituted the vector objective function. The closed-loop performance index was taken as the time integral of the Hamiltonian. Constraints on natural frequencies and aeroelastic damping were also considered. Derivatives of the objective and constraint functions with respect to structural and control design variables were derived for a finite element beam model of the structure and constant feedback gains determined by Independent Modal Space Control. Pareto optimal designs generated for a simple beam and a tetrahedral truss demonstrated the benefit of solving the integrated structural and control optimization problem. The use of quasi-steady aerodynamic strip theory with a thin-wall box beam model showed that the integrated design for a high aspect ratio, unswept, straight, isotropic wing can be separable. Finally, an efficient modal solution of the flutter equation facilitated the aeroelastic tailoring of a low aspect ratio, forward swept, composite plate wing model. / Ph. D.
|
53 |
Intelligent Active Vibration Control for a Flexible Beam SystemHossain, M. Alamgir, Madkour, A.A.M., Dahal, Keshav P., Yu, H. January 2004 (has links)
Yes / This paper presents an investigation into the
development of an intelligent active vibration control
(AVC) system. Evolutionary Genetic algorithms (GAs)
and Adaptive Neuro-Fuzzy Inference system (ANFIS)
algorithms are used to develop mechanisms of an AVC
system, where the controller is designed on the basis of
optimal vibration suppression using the plant model. A
simulation platform of a flexible beam system in
transverse vibration using finite difference (FD) method
is considered to demonstrate the capabilities of the AVC
system using GAs and ANFIS. MATLAB GA tool box for
GAs and Fuzzy Logic tool box for ANFIS function are
used for AVC system design. The system is then
implemented, tested and its performance assessed for GAs
and ANFIS based design. Finally a comparative
performance of the algorithm in implementing AVC
system using GAs and ANFIS is presented and discussed
through a set of experiments.
|
54 |
New paradigms to control coupled powertrain and frame motions using concurrent passive and active mounting schemesLiette, Jared V. 14 November 2014 (has links)
No description available.
|
55 |
An air suspension cushion to reduce human exposure to vibrationVan der Merwe, Andre Francois 03 1900 (has links)
Thesis (PhD (Industrial Engineering))--University of Stellenbosch, 2007. / Off-road working vehicles are subjected to high levels of vibration input on the rough
terrain and irregular roads they work. The human operators are therefore exposed to high
levels of whole body vibration (WBV) and at risk of developing health problems. A
number of international standards address the matter of whole body vibration, and the
European Union issued a directive which limits the exposure of workers in the EU to
WBV. Unfortunately, to date there is no law in South Africa requiring compliance with
any of these EU standards nor guidelines.
There are vehicles which are not fitted with suspension and/or suspension seats. The three
wheeled logger used in forestry is a highly manoeuvrable and effective bulk handler, but
without any form of suspension and no space under the operator’s seat to install a
suspension seat. However, a suspension cushion can be retrofitted to existing vehicles
largely alleviating the problem.
To isolate low frequency vibration large suspension travel is required which makes an air
suspension cushion attractive, as it can fully collapse. Additionally, a Helmholtz resonator
if added to the cushion in the form of a pipe and tank, provides anti-resonance at a specific
frequency. The resonator can be tuned by adjusting the pipe’s length and diameter as well
as the volume of the tank. Larger diameter pipes have less friction and give better
reduction of the transmissibility curve at the anti-resonance frequency.
The SEAT value is a single number used to compare suspension seats for a specific input
vibration. It is calculated from the weighted input acceleration power spectral density
curve and the suspension seat transmissibility curve. The former is obtained from the
vehicle and is vehicle, path and speed dependent. The latter is the only variable that can be
improved by using a better suspension seat/cushion. The input power spectral density
often contains significant energy at frequencies where the human operator is most
sensitive. The cushion resonator could be tuned to position the anti-resonance in the
transmissibility curve at these frequencies. The resultant output vibration would thus be
lower than the input vibration at that frequency.
In this dissertation an analytical model describes the state variables in the cushion, pipe
and tank. A Simulink model predicts the transmissibility curve with a solid mass as well
as with a two degree of freedom seated human model. Initially the prototype was tested
with a solid mass to compare the transmissibility curve produced by the simulation with
the experimental results. It was required to evaluate the contribution of the resonator
without the complexity of the human impedance. Subsequent tests were carried out with
human subjects. Test results showed high inter subject similarity at the anti-resonance
frequencies.
Design guidelines are formulated that can be used by the suspension cushion designer to
specify the pipe diameter and length and the volume of the tank to determine the optimal
transmissibility. Input psd from ISO7096 class EM3 vehicles is used as an example during
the design process.
A prototype air suspension cushion was designed to reduce output vibration on the three
wheeled logger. Laboratory tests with human subjects showed a significant improvement
at the problematic frequencies through the tuning of the resonator. Using a Helmholtz
resonator with the air suspension cushion the overall SEAT value improved by 25%
compared with a 100mm foam cushion. However, the current tank and pipe need to be
reduced in size for practical implementation to the vehicle.
Future work would include finding an alternative mass to replace the air in the pipe. This
should reduce the size of the tank and the pipe required. Additionally the simultaneous
effect of multiple resonators at different frequencies should be investigated. This is
required for vehicles having an input psd with significant energy at more than one
frequency band.
|
56 |
Next generation wavefront controller for the MMT adaptive optics system: Algorithms and techniques for mitigating dynamic wavefront aberrationsPowell, Keith January 2012 (has links)
Wavefront controller optimization is important in achieving the best possible image quality for adaptive optics systems on the current generation of large and very large aperture telescopes. This will become even more critical when we consider the demands of the next generation of extremely large telescopes currently under development. These telescopes will be capable of providing resolution which is significantly greater than the current generation of optical/IR telescopes. However, reaching the full resolving potential of these instruments will require a careful analysis of all disturbance sources, then optimizing the wavefront controller to provide the best possible image quality given the desired science goals and system constraints. Along with atmospheric turbulence and sensor noise, structural vibration will play an important part in determining the overall image quality obtained. The next generation of very large aperture telescopes currently being developed will require assessing the effects of structural vibration on closed loop AO system performance as an integral part of the overall system design. Telescope structural vibrations can seriously degrade image quality, resulting in actual spot full width half maximum (FWHM) and angular resolution much worse than the theoretical limit. Strehl ratio can also be significantly degraded by structural vibration as energy is dispersed over a much larger area of the detector. In addition to increasing telescope diameter to obtain higher resolution, there has also been significant interest in adaptive optics systems which observe at shorter wavelength from the near infrared to visible (VNIR) wavelengths, at or near 0.7 microns. This will require significant reduction in the overall wavefront residuals as compared with current systems, and will therefore make assessment and optimization of the wavefront controller even more critical for obtaining good AO system performance in the VNIR regime.
|
57 |
HUMAN-INDUCED VERTICAL VIBRATION ON PEDESTRIAN STRUCTURES: NUMERICAL AND EXPERIMENTAL ASSESSMENTDaniel Gomez Pizano (6865232) 02 August 2019 (has links)
In recent years civil engineering structures such as floors, footbridges, and staircases, have reported unacceptable vibration when they are dynamically excited by pedestrians. When such structures have a particular combination of high structural flexibility and low inherent damping, there is potential for excessive vibration. Pedestrian-structure interaction (PSI) is especially noticeable when the lowest structural natural frequencies are close to the dominant pedestrian pace frequency or its harmonics. Although most of these structures are designed according to existing standards and guidelines, there are still many uncertainties in the human actions that may lead to unexpected structural behavior, increasing the vibration responses and exceeding serviceability limit states. How a pedestrian excites a structure and how that structure affects a pedestrian's gait is not fully understood. Therefore, a realistic analysis of PSI must be performed to properly incorporate these effects toward more rational structural designs. This study aims to identify, within this class of the walking-induced load problem, the vibration mechanisms, the mathematical models, and methods, to address excessive vibration in pedestrian structures. After conducting an in-depth evaluation of current guidelines and provisions for analysis and design of pedestrian structures, models to enable more realistic design under such uncertainties have been developed. The results establish a body of knowledge regarding human loads and structural responses, yielding the potential for more rational approaches to improve the analysis and design of pedestrian structures.
|
58 |
Disturbance Attenuation in Mass Chains with Passive InterconnectionYamamoto, Kaoru January 2016 (has links)
This thesis is concerned with disturbance amplification in interconnected systems which may consist of a large number of elements. The main focus is on passive control of a chain of interconnected masses where a single point is subject to an external disturbance. The problem arises in the design of multi-storey buildings subjected to earthquake disturbances, but applies in other situations such as bidirectional control of vehicle platoons. It is shown that the scalar transfer functions from the disturbance to a given intermass displacement can be represented as a complex iterative map. This description is used to establish uniform boundedness of the H∞-norm of these transfer functions for certain choices of interconnection impedance. A graphical method for selecting an impedance such that the H∞-norm is no greater than a prescribed value for an arbitrary length of the mass chain is given. A design methodology for a fixed length of the mass chain is also provided. A case study for a 10-storey building model demonstrates the validity of this method.
|
59 |
Active Vibration Control of Helicopter Rotor Blade by Using a Linear Quadratic RegulatorUddin, Md Mosleh 18 May 2018 (has links)
Active vibration control is a widely implemented method for the helicopter vibration control. Due to the significant progress in microelectronics, this technique outperforms the traditional passive control technique due to weight penalty and lack of adaptability for the changing flight conditions. In this thesis, an optimal controller is designed to attenuate the rotor blade vibration. The mathematical model of the triply coupled vibration of the rotating cantilever beam is used to develop the state-space model of an isolated rotor blade. The required natural frequencies are determined by the modified Galerkin method and only the principal aerodynamic forces acting on the structure are considered to obtain the elements of the input matrix. A linear quadratic regulator is designed to achieve the vibration reduction at the optimum level and the controller is tuned for the hovering and forward flight with different advance ratios.
|
60 |
DESIGN, MODELING AND EXPERIMENTAL VERIFICATION OF A NONLINEAR ENERGY SINK BASED ON A CANTILEVER BEAM WITH SPECIALLY SHAPED BOUNDARIESChristian Eduardo Silva (7491146) 17 October 2019 (has links)
This dissertation focuses on the design, modeling, characterization and experimental verification of a class of nonlinear energy sink, based on a cantilever beam vibrating laterally between two specially shaped surfaces that limit the vibration amplitude, thus providing a variable beam length throughout its deflection, therefore producing a smooth nonlinear restoring force. First, a methodology to evaluate and visualize the energy interactions between the nonlinear energy sink and its host structure is developed. Then, an semi-analytical dynamic model for simulating the device under actual working conditions is proposed, and finally, an experimental verification step is conducted where the numerical results are compared and correlated to the experimental results.<br>
|
Page generated in 0.0779 seconds