Ceramics and polymer-ceramic composites associated with high dielectric constants are of both scientific and industrial interest as these could be used in devices such as capacitors, resonators and filters. High dielectric constant facilitates smaller capacitive components, thus offering the opportunity to miniaturize the electronic devices. Hence there is a continued interest on high dielectric constant materials over a wide range of temperatures. Recently, CaCu3Ti4O12 (CCTO) ceramic which has centro-symmetric body centered cubic structure has attracted considerable attention due to its large dielectric constant (ε ~104-105) which is nearly independent of frequency (upto 10 MHz) and low thermal coefficient of permittivity (TCK) over 100-600K temperature range. Apart from the high dielectric ceramics, high dielectric polymer-ceramic composites have also become promising materials for capacitor applications. By combining the advantages of high dielectric ceramics and low leakage behaviour of polymers, one can fabricate new hybrid materials with high dielectric constants, and high breakdown field to achieve high volume efficiency and energy storage density for capacitor applications. The CCTO polycrystalline powders were generally prepared by the conventional solid-solid reaction route with CaCO3, TiO2 and CuO as the starting materials. This method of preparation often requires high temperatures and longer durations. To overcome these difficulties, in the present investigations, an attempt has been made to synthesize CCTO by adopting microwave assisted heating technique and wet chemical synthesis routes. Also the CCTO crystallites (size varying from nano to micrometers) incorporated in the Polyvinyliden fluoride (PVDF) and Polyaniline (PANI) matrix and several composites with high dielectric constants were fabricated and investigated. Further, the high dielectric constant glasses in the system (100-x)TeO2-xCaCu3Ti4O12, (x=0.5 to 3) were fabricated by the conventional melt-quenching technique and their structural and dielectric properties were studied. The results obtained pertaining to these aforementioned investigations are classified as follows. Chapter 1 is intended to give basic information pertaining to the dielectrics and various mechanisms associated with high dielectric constants. Brief exposure to the high dielectric constant materials is also given. The structural aspects of CCTO, various synthetic routes adopted for the synthesis and the origin of the dielectric anomaly in CCTO are elaborated. In addition, basic information about the high dielectric polymer-ceramic composites and glasses are provided. In chapter 2 the various experimental techniques that were employed to synthesize and characterize the materials under investigation were discussed. Chapter 3 reports the synthesis and characterization of CaCu3Ti4O12, (CCTO) powders by microwave assisted heating at 2.45 GHz, 1.1kW. The processing and sintering were carried out at different temperatures for varied durations. The optimum calcination temperature using microwave heating was found to be 950oC for 20 minutes to obtain cubic CCTO powders. This is found to be fast and energy efficient as compared to that of the conventional methods. The structure, morphology and dielectric properties of the CCTO ceramic processed by microwave assisted heating were studied via X-ray diffraction, Scanning electron microscopy (SEM) and impedance analyser. These studies revealed that, the microwave sintered (MS) samples were less porous than that of the conventional ones. Relative density of about 95% was achieved for the MS pellets (1000oC/60min) while for the conventional sintered (CS) pellets (1100oC/2h) it was only 91%. The dielectric constants for the microwave sintered (1000oC/60min) ceramics were found to vary from 11000 to 6950 in the 100 Hz to 100 kHz frequency range. The presence of larger grains (6-10μm) in the MS samples contributed to the higher dielectric constants. Chapter 4 deals with the synthesis of complex oxalate precursor, CaCu3(TiO)4(C2O4)8 • 9H2O, by the wet chemical route. The various trials and the different reaction schemes involved for the preparation of complex oxalate precursor were highlighted. The oxalate precipitate thus obtained was characterized by the wet chemical analyses, X-ray diffraction, FTIR absorption and TG/DTA analyses. The complex oxalate precursor, CaCu3(TiO)4(C2O4 )8.9H2O was subjected to thermal oxidative decomposition and the products of thermal decomposition were investigated employing XRD,TGA, DTA and FTIR techniques. Nanocrystallites of CaCu3Ti4O12 with the size varying from 30-200 nm were obtained at a temperature as low as 680oC. The nanocrystallites of CaCu3Ti4O12 were characterized using Electron Spin Resonance (ESR) and optical reflectance techniques. The selected area electron diffraction (SAED) pattern with the zone axis [012] and spot pattern in electron diffraction (ED) indicate their single-crystalline nature. The optical reflectance and ESR spectra indicate that the Cu (II) coordination changes from distorted octahedra to nearly flattened tetrahedra (squashed) to square planar geometry with increasing heat treatment temperature. The powders derived from the oxalate precursor have excellent sinterability resulting in high density ceramics which exhibited giant dielectric constants upto 40,000 (1 kHz) at 25oC, accompanied by low dielectric loss < 0.07. The effect of calcium content on the dielectric properties of CaxCu3Ti4O12 (x=0.90, 0.97, 1.0, 1.1 and 1.15) derived from the oxalate route was described in Chapter 5. The structural, morphological and dielectric properties of the ceramics were studied using X-ray diffraction, Scanning Electron Microscope along with Energy Dispersive X-ray Analysis (EDX), and Impedance analyzer. The X-ray diffraction patterns obtained for the x= 0.97, 1.0 and 1.1 ceramics could be indexed to a body– centered cubic perovskite related structure associated with the space group Im3. The microstructural studies revealed that the grains are surrounded by exfoliated sheets of Cu-rich phase. The microstructure that is evolved for the Ca0.97 ceramic more or less resembles that of the Ca1.0 ceramic, but the density of such exfoliated sheets of cu-rich phase is lesser for the Ca0.97 ceramic and none for Ca1.1 ceramic. The sintered pellet (x=0.97) was ground and thinned to the required thickness (~ 20nm) and analyzed using Transmission Electron Microscopy (TEM). The current-voltage (I-V) characteristics of the ceramics exhibited non-linear behaviour. The dielectric properties of these suggest that the sample corresponding to the composition x=0.97, has a reduced dielectric loss while retaining its high dielectric constant. Chapter 6 illustrates the results concerning the fabrication and characterization of nanocrystal composites of Polyaniline (PANI) and CaCu3Ti4O12 (CCTO). These were prepared using a simple procedure involving in-situ polymerization of aniline in dil. HCl. The PANI and the PANI-CCTO composites were subjected to X-ray diffraction, Fourier Transform Infrared (FTIR), Thermo gravimetric, Scanning Electron Microscopic (SEM) and Transmission electron microscopic analyses. The FTIR spectra recorded for the composites was similar to that of pure PANI unlike in the case of X-ray diffraction wherein the characteristics of both PANI and CCTO were reflected. The TGA in essence indicated the composites to have better thermal stability than that of pure PANI. The composite corresponding to 50%CCTO-50%PANI exhibited higher dielectric constant (4.6x106 @100Hz). The presence of the nano crystallites of CCTO embedded in the nanofibers of PANI matrix was established by TEM. The AC conductivity increased slightly upto 2kHz as the CCTO content increased in the PANI which was attributed to the polarization of the charge carriers. The value of dielectric constant obtained was higher than that of the other PANI based composites reported in the literature. Chapter 7 deals with the fabrication and characterization of diphasic Poly(vinylidene fluoride) (PVDF)-CCTO composite. The CCTO crystallites (size varying from nano to micrometers) incorporated in the Polyvinylidene fluoride (PVDF) and composites with varying CCTO content were fabricated. The structural, morphological and dielectric properties of the composites were studied using X-ray diffraction, Thermal analysis, Scanning Electron Microscope (SEM), Transmission Electron Microscopic (TEM) and Impedance analyzer. The room temperature dielectric constant as high as 95 at 100Hz has been realized for the composite with 0.55 Vol.fraction of CCTO (micro sized crystallites), which has increased to about 190 at 150oC. Whereas, the PVDF/CCTO nanocrystal composite with 0.13Vol.fraction of CCTO has exhibited higher room temperature dielectric constant (90 at 100Hz). The PVDF/CCTO nanocrystal composite was further investigated for the breakdown strength and electric modulus. The breakdown strength plotted against the dielectric constant evidenced an inverse relationship of breakdown voltage with the dielectric constant. The relaxation processes associated with these composites were attributed to the interfacial polarization or Maxwell-Wagner-Sillars (MWS) effect. Various theoretical models were employed to rationalize the dielectric behavior of these composites. The fabrication and characterization details of optically clear colored glasses in the system (100-x)TeO2-xCaCu3Ti4O12, (x=0.5 to 3 mol%) are reported in Chapter 8. The color varies from olive green to brown as the CaCu3Ti4O12 (CCTO) content increased in TeO2 matrix. The X-ray powder diffraction and differential scanning calorimetric analyses that were carried out on the as-quenched samples confirmed their amorphous and glassy nature respectively. The optical transmittance of the glasses exhibited typical band-pass filter characteristics. The dielectric constant and loss in the 100 Hz-1MHz frequency range were monitored as a function of temperature (323K673K). The dielectric constant and the loss increased as the CCTO content increased in TeO2 at all the frequencies and temperatures under study. Further, the dielectric constant and the loss were found to be frequency independent in the 323-473 K temperature range. The value obtained for the loss at 1MHz was 0.0019 which was typical of low loss materials, and exhibited near constant loss (NCL) contribution to the ac conductivity in the 100Hz-1MHz frequency range. The electrical relaxation was rationalized using the electrical modulus formalism. These glasses are found to be more stable (a feature which may be of considerable interest) as substrates for high frequency circuit elements in conventional semiconductor industries. Thesis ends with summary and conclusions, though each chapter is provided with conclusions and complete list of references.

Ce travail porte sur la modification de matrices polymères à base de fluorure de vinylidene pour permettre leur utilisation en tant que membrane séparatrice dans les supercapacités. Basé sur un procédé d‘irradiation par rayonnement γ, l‘objectif principal était la limitation du gonflement du polymère lorsqu‘il est mis en contact d‘un milieu liquide relatif à l‘application tout en gardant d‘excellentes affinités avec celui-ci. Le processus de base exploité étant la formation et la réaction des radicaux lors de l‘irradiation du polymère, une partie de la thèse a été consacrée à leur étude par résonance paramagnétique électronique (RPE). Un modèle de simulation de spectre RPE a été mis en place pour identifier et quantifier chacune des espèces radicalaires. L‘effet de la dose d‘irradiation, de la durée d‘un recuit et de la nature de la matrice polymère (homo, copolymère) sur la proportion de ces espèces et sur leur réactivité a été évalué. Un lien avec la formation d‘un réseau a été proposé. Une attention particulière a ensuite été apportée à l‘augmentation de la densité de réticulation avec le concours d‘un agent réticulant, le TAIC. Pour terminer, une stratégie de modification des propriétés de surface du PVDF a été élaborée. Elle consiste dans un premier temps à radiogreffer un polymère à la surface du PVDF puis à modifier, dans un second temps, les greffons par une chimie douce et sélective. En conclusion, les approches complémentaires développées au cours de cette thèse ont permis de comprendre la radiolyse des polymères et de mettre à profit les processus élémentaires pour développer des stratégies robustes et prometteuses de modulation des propriétés. / This work deals with the modification of VDF-based polymer induced by γ-radiation as the polymer may be used in electrochemical supercapacitors. The main objective was to limit the swelling of the fluorinated matrix with a given electrolyte while a good wetting of the polymer by the liquid was also required. As the main basic process involved in polymer radiolysis is the formation of radicals, a part of the work was dedicated to the study of such species by using Electron Spin Resonance spectroscopy. A simulation model of ESR spectra was established in order to identify and quantify each radical species. The effect of several parameters such as radiation dose, annealing time or the nature of polymer matrix on the concentration of each species where investigated. A relation with the evolution of the crosslink density of the network formed during the radiolisys was proposed. In addition, one of the key steps of this work was to study the radiation crosslinking ability of VDF-based polymers and find a way to increase the crosslink density. This was achieved by incorporating, prior to the radiation process, a radiation sensitive crosslinker: TAIC. Finally, a new strategy based on the modification of surface properties of PVDF was investigated. It consists in the radiation grafting of pentafluorstyrene onto PVDF surface followed by the chemioselective functionalization of the grafted segments. As a conclusion, the different approaches used in this thesis allowed us to understand the radiolysis of VDF-based polymers and take advantage of the elementary process involved in this type of chemistry, to build up robust and promising strategies for tuning properties.

Le caoutchouc naturel (NR) et le caoutchouc époxydé (ENR) ont constitué la base de cette étude consacrée à l’étude des composites et mélanges de polymères. La présence du groupe époxyde a conduit à une amélioration des propriétés mécaniques de ces formulations en termes de module et de la résistance à la traction. De plus, l’utilisation de la spectroscopie diélectrique a révélé que les ENRs présentent une conductivité plus élevée que le NR à basse fréquence et à haute température. En particulier, le caoutchouc naturel époxidé contenant 50 mol% de groupes époxyde ENR-50 présente des conductivités et permittivités les plus élevées. Par conséquent, ce dernier a été choisi pour préparer des composites polymères en incorporant des particules de titanate de barium (BT) et de noir de carbone (CB). Les résultats montrent que la permittivité et conductivité des composites élaborés augmentent avec le taux d'incorporation de ces charges. Par exemple, les composites BT/ENR-50 atteignent une permittivité élevée 48.7 pour 50 vol% de BT. De plus, les composites CB/ENR-50 présentent un seuil de percolation de 6.3 vol% de CB. Enfin les mélanges à base de poly(fluorure de vinylidène) (PVDF) et d’ENR ont été étudiés. Il a été observé que la morphologie de ces mélanges dépend du degré d’époxydation du caoutchouc naturel et bien entendu de la composition du mélange. Une morphologie co-continue peut être observée dans l’intervalle 40 et 60% en masse d’ENR-50. En outre, les résultats issus d’analyses dynamiques mécanique et diélectrique montrent que ces mélanges présentent une miscibilité partielle. Enfin, des composites à base de ces mélanges binaires PVDF/ENR- 50 contenant BT ont été préparés. L’étude des morphologies a révélé que les particules de BT étaient dispersées dans la phase d’ENR-50 pour le mélange classique. Cependant, les particules de BT sont localisées à l'interface et dans la phase PVDF pour le mélange réticulé dynamiquement. En termes de propriétés, la permittivité plus élevée est obtenue pour le mélange PVDF/ENR 50 (80/20) ayant été réticulé dynamiquement / Natural rubber (NR) and epoxidized natural rubber (ENR) were chosen to study the composites and blends of polymers. The presence of epoxide group caused to improve the mechanical properties in terms of modulus and tensile strength. Furthermore, dielectric spectroscopy revealed that ENR showed conductivity process at low frequency and high temperature. Epoxidized natural rubber containing 50 mol% of epoxide group or ENR-50 exhibited the highest dielectric permittivity and electrical conductivity. Therefore, ENR-50 was then selected to prepare polymer composite filled with barium titanate (BT) and carbon black (CB) particles. The permittivity and conductivity of the composites increased with the volume content of the fillers. The BT/ENR-50 composites reached a high permittivity of 4 8 . 7 for addition of 50 vol% BT. Meanwhile, CB/ENR-50 composite reached percolation threshold at 6. 3 vol% of CB. The phase development and miscibility of poly(vinylidene fluoride) (PVDF)/epoxidixed natural rubber (ENR) blends were then investigated. It was also found that phase structure depended on epoxidation level and blend compositions. The blend exhibited a co-continuous phase morphology in the region of 40 to 60 wt% of ENR-50. Furthermore, the results from dynamic mechanical and dielectric analysis revealed that these blends present a partial miscibility. Finally, the composites based on binary blends of PVDF/ENR-50 containing BT were prepared. The study of the morphologies revealed that BT was dispersed in ENR-50 phase in the case of simple blend. However, the addition of BT after dynamic vulcanization induced localization of BT in PVDF phase and at interface. The highest increment of permittivity can be observed for the composite based on dynamically cured PVDF/ENR-50 (80/20) blend / ศึกษาอิทธิพลของโครงสร้างโมกุลยางธรรมชาติ (NR) และยางธรรมชาติอิพอกไซด์ (ENR) ต่อสมบัติ พบว่าการมีหมู่อิพอกไซด์อยู่ในยาง ENR ทำให้มีการปรับปรุงสมบัติเชิงกล เช่น มอดุลัสและความต้านทานต่อแรงดึง นอกจากนี้สมบัติไดอิเล็กทริกได้แสดงให้เห็นถึงการนำ ไฟฟ้าที่ความถี่ต่ำและอุณหภูมิสูง ยางที่มีหมู่อิพอกไซด์ 50 โมล% (ENR-50) มีค่าการนำไฟฟ้า และค่า permittivity สูงที่สุด ดังนั้นจึงนำยาง ENR-50 ไปใช้ในการเตรียมคอมพอสิตที่ใช้แบเรียม ไททาเนตและเขม่าดำเป็นตัวเติม ซึ่งพบว่าค่า permittivity และค่าการนำไฟฟ้าสูงขึ้นตาม ปริมาณตัวเติมที่ใส่ลงไป ที่ปริมาณ 50%โดยปริมาตรของแบเรียมไททาเนตในยางให้ค่า permittivity สูงถึง 48.7 ในขณะเดียวกันก็พบว่าการเตรียม ENR-50 คอมพอสิตที่ใช้เขม่าดำมี percolation threshold ที่ 6.3 vol% ของเขม่าดำ สำหรับการศึกษาการเปลี่ยนแปลงของสัณฐาน วิทยาและความเข้ากันได้ของพอลิเมอร์เบลนด์ระหว่างพอลิไวนิลลิดีนฟลูออไรด์ (PVDF) กับยาง ENR พบว่า สัณฐานวิทยาของพอลิเมอร์ที่เตรียมได้ขึ้นอยู่กับปริมาณหมู่อิพอกไซด์ในยาง ENR และอัตราส่วนการเบลนด์ อัตราส่วนการเบลนด์ในช่วง 40 ถึง 60% โดยน้ำหนักของยาง ENR- 50 ให้ลักษณะสัณฐานวิทยาแบบวัฏภาคร่วม (co-continuous) นอกจากนี้ผลการทดสอบจาก สมบัติพลวัตเชิงกลและสมบัติไดอิเล็กทริกแสดงให้เห็นถึงความเข้ากันได้บางส่วน (partial miscibility) ท้ายที่สุดนี้ได้เตรียมคอมพอสิตจากพอลิเมอร์เบลนด์ที่เติมแบเรียมไททาเนต สัณฐานวิทยาของคอมโพสิทที่เตรียมได้นั้น พบว่าแบเรียมไททาเนตกระจายตัวในเฟสยางเป็น หลัก อย่างไรก็ตามการเติมแบเรียมไททาเนตหลังจากการวัลคาไนซ์แบบไดนามิกส์ทำให้ แบเรียมไททาเนตกระจายตัวในเฟสพอลิไวนิลลิดีนฟลูออไรด์ (PVDF) และที่ผิวประจัญ (interface) นอกจากนี้คอมพอสิตที่เตรียมจากเทอร์โมพลาสติกวัลคาไนซ์ของ PVDF/ENR 50 ที่ อัตราส่วนการเบลนด์ที่ 80/20 ให้ค่า permittivity ที่สูง

Ce travail de thèse porte sur la compréhension du rôle polyvalent des liquides ioniques (LIs) phosphonium comme agents de nanostructuration et interfaciaux pour la matrice polymère fluorée poly(fluorure de vinylidène-chlorotrifluoroéthylène) (P(VDF-CTFE)). Dans un premier temps, deux LIs phosphonium avec des fonctionnalités différentes générant un encombrement stérique et des fonctions dipolaire additionnelles sont tout d'abord incorporés dans la matrice P(VDF-CTFE) pour préparer des films de polymère additives. La structure de la phase cristalline, la morphologie issue de la dispersion et le comportement de cristallisation sont finement caractérisés dans le but de fournir une compréhension fuie et complète du rôle joué par le LI sur la nanostructuration. Dans un second temps, le rôle d’agent interfacial du LI est étudié avec un LI phosphonium fluoré comprenant un cation combinant trois phényles et une chaîne fluorée courte.Ce LI est utilise pour modifier la surface de l'oxyde de graphène (GO) et de l'oxyde de graphène réduit (rGO) afin de rendre ces nanocharges fonctionnelles et les incorporer dans la matrice P(VDF-CTFE). Ainsi, des films composites de P(VDF-CTFE)/graphène avec différentes teneurs en nanocharges sont préparés et une caractérisation fuie de la structure et des propriétés est entreprise afin de mieux comprendre les mécanisme d’interaction interfaciale et leurs influences sur les films composites, tels que la structure de la phase cristalline, le comportement de cristallisation, la relaxation des chaînes, la morphologie et les propriétés diélectriques finales. / This thesis work deals with an understanding of the versatile roles of phosphonium ionic liquids (ILs) as nanostructuration and interfacial agents for the fluorinated polymer matrix, i.e.,poly(vinylidene fluoride-chlorotrifluoroethylene) (P(VDF-CTFE)). In this context, two phosphonium ILs with different functionalities in steric hindrance and extra dipolar groups are firstly incorporated in P(VDF-CTFE) matrix to prepare polymer films. The crystalline phase structure, dispersion morphology and crystallization behavior are finely characterized with the goal of providing a full and deep understanding of the versatile and tunable nanostructuration effect of phosphonium ILs. Subsequently, in order to elucidate the mechanism of interfacial influence of IL, a fluorinated phosphonium IL with a cation structure combining three phenyls and a short fluorinated chain is added on the surface of graphene oxide (GO) and reduced graphene oxide (rGO), making them as functional nanofillers to be incorporated into P(VDF-CTFE) matrix. Thus,P(VDF-CTFE)/graphene composite films with different filler contents are prepared in order to investigate the mechanism of interfacial interaction and its influence on the composite films, such as crystalline phase structure, crystallization behavior, chain segmental relaxation behavior, dispersion morphology and the final dielectric properties.

Les travaux réalisés portent sur la synthèse de nanoparticules de PVDF à l’aide de la polymérisation radicalaire contrôlée (PRC) par transfert de chaîne réversible par addition-fragmentation (RAFT) en émulsion. Dans un premier temps, un méthoxy poly(éthylène glycol) commercial porteur d’une fonction hydroxyle (PEG-OH) a été employé pour la stabilisation des particules de PVDF. Cette stabilisation est assurée par des réactions de transfert irréversible opérant le long des chaînes de PEG conduisant à la formation in situ d’un stabilisant de type copolymère greffé. Par la suite, un PEG modifié chimiquement à partir du PEG-OH, portant à son extrémité de chaîne une fonction xanthate (macroRAFT, PEG-X), réactive et réactivable, a été utilisé. Les expériences réalisées en présence de ce macroRAFT ont démontré une forte implication de l’extrémité xanthate dans le procédé de polymérisation en émulsion du VDF. En effet, des particules stables de l’ordre de 70 nm de diamètre sont obtenues, alors que l’utilisation de PEG-OH conduit à des tailles beaucoup plus importantes (200 nm). Cette tendance est confirmée lors de l’étude de l’impact de divers paramètres comme la masse molaire de la chaîne PEG ou encore la quantité d’amorceur. Des analyses complémentaires (tension de surface et calorimétrie différentielle à balayage) ont permis de comparer le taux d’ancrage de PEG-X et de PEG-OH. Les quantités en macroRAFT ont ensuite été augmentées dans le but d’obtenir des particules composées de copolymères à blocs. Des analyses RMN approfondies ont été menées pour identifier les espèces créées lors de la polymérisation en émulsion du VDF lorsque PEG-OH et PEG-X sont utilisés en tant que stabilisant. Par comparaison, des PEG portant des fonctions réactives de types (méth)acrylate et thiol ont également été employés comme stabilisant et leurs efficacités comparées à celles de PEG-OH et de PEG-X. Par ailleurs, d’autres architectures à base de PEG ont été évaluées en utilisant un macroRAFT difonctionnel (X-PEG-X) et un polymère greffé (PPEGA-X). Enfin, des latex de PVDF ont été synthétisés en présence de macroRAFT de type poly(acide (méth)acrylique) obtenus par polymérisation RAFT de l’acide acrylique ou méthacrylique en présence d’un trithiocarbonate ou d’un xanthate. Comme précédemment, plusieurs paramètres ont été variés comme la masse molaire des chaînes macromoléculaires, la quantité d’amorceur et la quantité de macroRAFT. Ces études ont encore une fois démontré la forte implication des extrémités RAFT dans la stabilisation des particules de PVDF / This work describes the synthesis of self-stabilized PVDF particles by combining the advantages of emulsion polymerization with those of controlled radical polymerization (CRP) using the RAFT process. First, a commercial methoxy poly(ethylene glycol) carrying a hydroxyl function (PEG-OH) was used for the stabilization of PVDF particles. The stabilization is provided by irreversible transfer reactions occurring along the PEG-OH chains leading to the formation of a grafted copolymer stabilizer in situ. This PEG-OH was then chain-end functionalized to introduce a xanthate group (macroRAFT, PEG-X). The experiments carried out in the presence of this macroRAFT demonstrated a strong implication of the xanthate chain-end in the VDF emulsion polymerization process. Indeed, particle sizes of 200 nm and 70 nm were obtained in the presence of PEG-OH and PEG-X, respectively. This trend was confirmed during the study of the impact of various parameters such as the molar mass of the PEG chain or the initiator amount. Additional analyses (surface tension measurement and differential scanning calorimetry) allowed to compare the anchoring efficiency of PEG-X and PEG-OH. The macroRAFT amount was then increased to form particles composed of block copolymer. In-depth NMR analyses were then conducted to identify the species created during the VDF emulsion polymerization process in the presence of PEG-OH and PEG-X. In comparison, PEGs carrying reactive functions such as (meth)acrylate and thiol were used as stabilizers and their efficiencies compared to those of PEG-OH and PEG-X. The macroRAFT architecture was also varied using a difunctional macroRAFT (X-PEG-X) and a grafted polymer (PPEGA-X). Finally, PVDF latexes were synthesized with poly((meth)acrylic acid) (P(M)AA) functionalized by either a trithiocarbonate or a xanthate. Like previously, several parameters were varied such as the macromolecular chain length, the initiator amount and the macroRAFT amount. Again, these studies demonstrated the strong impact of the RAFT chain-end in the stabilization of PVDF particles