One of the greatest challenges facing the nuclear power industry is the final disposition of nuclear waste. To meet the needs of the nuclear power industry, a new fuel assembly design, called DUPLEX, has been developed which provides higher fuel burnups, burns transuranic waste while reducing minor actinides, reduces the long term radiotoxicity of spent nuclear fuel, and was developed for use in current light water reactors. The DUPLEX design considered in this thesis is based on a seed and blanket unit (SBU) configuration, where the seed region contains standard UO2 fuel, and the blanket region contains an inert matrix (Pu,Np,Am)O2-MgO-ZrO2 fuel. The research efforts of this thesis are first to consider the higher burnup effects on DUPLEX assembly thermal-hydraulic performance and thermal safety margin over the assembly’s expected operational lifetime. In order to accomplish this, an existing burnup-dependent thermal-hydraulic methodology for conventional homogeneous fuel assemblies has been updated to meet the modeling needs specific to SBU-type assemblies. The developed framework dramatically expands the capabilities of the latest thermal-hydraulic evaluation framework such that the most promising and unique DUPLEX fuel design can be evaluated. As part of this updated methodology, the posed DUPLEX design is evaluated with respect to the minimum departure from nucleate boiling ratio, peak fuel temperatures for both regions, and the peak cladding temperatures, under ANS Condition I, II, and III transient events with the thermal-hydraulic code VIPRE-01. Due to difficulty in the fabrication and handling of minor actinide dioxides, documented thermal conductivity values for the considered IMF design are unavailable. In order to develop a representative thermal conductivity model for use in VIPRE-01, an extensive literature survey on the thermal conductivity of (Pu,Np,Am)O2-MgO-ZrO2 component materials and a comprehensive review of combinatory models was performed. Using the updated methodology, VIPRE-01 is used to perform steady-state and transient thermal hydraulic analyses for the DUPLEX fuel assembly. During loss-of-flow accident scenarios, the DUPLEX design is shown to meet imposed safety criteria. However, using the most conservative thermal conductivity modeling approach for (Pu,Np,Am)O2-MgO-ZrO2, the blanket region fuel temperatures remain only slightly below the design limit.

Two new fuel assembly designs for light water reactors using advanced mixed-oxide fuels have been proposed to reduce the radiotoxicity of used nuclear fuel discharged from nuclear power plants. The research efforts of this thesis are the first to consider the effects of burnup on advanced mixed-oxide fuel assembly performance and thermal safety margin over an assembly?s expected operational burnup lifetime. In order to accomplish this, a new burnup-dependent thermal-hydraulic analysis methodology has been developed. The new methodology models many of the effects of burnup on an assembly design by including burnup-dependent variations in fuel pin relative power from neutronic calculations, assembly power reductions due to fissile content depletion and core reshuffling, and fuel material thermal-physical properties. Additionally, a text-based coupling method is developed to facilitate the exchange of information between the neutronic code DRAGON and thermal-hydraulic code VIPRE-01. The new methodology effectively covers the entire assembly burnup lifetime and evaluates the thermal-hydraulic performance against ANS Condition I, II, and III events with respect to the minimum departure from nucleate boiling ratio, peak cladding temperatures, and fuel centerline temperatures. A comprehensive literature survey on the thermal conductivity of posed fuel materials with burnup-dependence has been carried out to model the advanced materials in the thermal-hydraulic code VIPRE-01. Where documented conductivity values are not available, a simplified method for estimating the thermal conductivity has been developed. The new thermal conductivity models are based on established FRAPCON-3 fuel property models used in the nuclear industry, with small adjustments having been made to account for actinide additions. Steady-state and transient thermal-hydraulic analyses are performed with VIPRE- 01 for a reference UO2 assembly design, and two advanced mixed-oxide fuel assembly designs using the new burnup-dependent thermal-hydraulic analysis methodology. All three designs maintain a sufficiently large thermal margin with respect to the minimum departure from nucleate boiling ratio, and maximum cladding and fuel temperatures during partial and complete loss-of-flow accident scenarios. The presence of a thin (Am,Zr)O2 outer layer on the fuel pellet in the two advanced mixed-oxide fuel assembly designs increases maximum fuel temperatures during transient conditions, but does not otherwise greatly compromise the thermal margin of the new designs.

This report investigates the steps of a one-way coupling between two simulation codes developed by Wesinghouse Electric Sweden AB. The Westinghouse POLCA8 is a three dimensional steady-state diffusion theory code used for simulating the neutronic, thermal and hydraulic behavior of a reactor core. In the  thermal-hydraulic module of the code, each fuel assembly is simulated as a one-dimensional channel, accounting for axial variations of the fuel geometry. While sufficient for many applications, the one-dimensional thermal-hydraulic approach may lack spatial resolution in the case of tilted radial power, very inhomogeneous fuel lattices or for specific calculations such as CHF (Critical Heat Flux) in PWR [3]. This limitation will b avoided by performing a code coupling with the sub-channel analysis code, VIPRE-W, to obtain the radial distribution of thermal-hydraulic parameters for each fuel assembly. In this thesis the codes are one-way coupled . To be able to do a coupling an interface is needed, and this has been created in Matlab. In the interface, the output from POLCA8 is converted into a form suitable to use as an input to VIPRE-W.  As an important first step in the coupling process, I have first analyzed how consistent the codes are when simulating the simplest thermal conditions inside the core. To be able to do the comparison,all values extracted from the sub-channel analysis code VIPRE-W must be converted into assembly-average-values, this is also done in the interface. The thermal-hydraulic parameters that have been  analyzed and compared in the two codes are; mass flux, quality and void.

The Multi-Application Small Light Water Reactor (MASLWR) is a small natural circulation pressurized light water reactor design that was developed by Oregon State University (OSU) and Idaho National Engineering and Environmental Laboratory (INEEL) under the Nuclear Energy Research Initiative (NERI) program to address the growing demand for energy and electricity. The MASLWR design is geared toward providing electricity to small communities in remote locations in developing countries where constructions of large nuclear power plants are not economical. The MASLWR reactor is designed to operate for five years without refueling and with fuel enrichment up to 8 %. In 2003, an experimental thermal hydraulic research facility also known as the OSU MASLWR Test Facility was constructed at Oregon State University to examined the performance of new reactor design and natural circulation reactor design concepts. This thesis is focused on the thermal hydraulics analysis and fuel performance analysis of the MASLWR prototypical cores with fuel enrichment of 4.25 % and 8 %. The goals of the thermal hydraulic analyses were to calculate the departure nucleate boiling ratio (DNBR) values, coolant temperature, cladding temperature and fuel temperature profiles in the hot channel of the reactor cores. The thermal hydraulic analysis was performed for steady state operation of the MASLWR prototypical cores. VIPRE Version 01 is the code used for all the computational modeling of the prototypical cores during thermal hydraulic analysis. The hot channel and hot rod results are compared with thermal design limits to determine the feasibility of the prototypical cores. The second level of analysis was performed with a fuel performance code FRAPCON for the limiting MASLWR fuel rods identified by the neutronic and thermal hydraulic analyses. The goals of the fuel performance analyses were to calculate the oxide thickness on the cladding and fission gas release (FGR). The oxide thickness results are compared with the acceptable design limits for standard fuel rods. The results in this research can be helpful for future core designs of small light water reactors with natural circulation. / Graduation date: 2012