No description available.

No description available.

Water distribution network models are used for different purposes. In this study, a model, used for daily operational issues is concerned. Models results should be consistent with actual conditions for sound decisions during operational studies. Adjusting model parameters according to site measurements in order to fit the model to obtain realistic results is known as calibration. Researchers have carried out numerous studies on calibration and developed various methods. In this study, an actual network (N8.3 Pressure Zone, Ankara) has been calibrated by two classical methods developed by Walski (1983) and Bhave (1988). The network parameter calibrated in this study is Hazen-Williams roughness coefficient, C-factor, and other parameters have been lumped in the C-factor. Results of the analysis showed that, C-factors have been found in a wide range.

This study gives a description about the development of a computer model, RealPipe, which relates genetic algorithm (GA) to the well known problem of least-cost design of water distribution network. GA methodology is an evolutionary process, basically imitating evolution process of nature. GA is essentially an efficient search method basically for nonlinear optimization cases. The genetic operations take place within the population of chromosomes. By means of various operators, the genetic knowledge in chromosomes change continuously and the success of the population progressively increases as a result of these operations. GA optimization is also well suited for optimization of water distribution systems, especially large and complex systems. The primary objective of this study is optimization of a water distribution network by GA. GA operations are realized on a special program developed by the author called RealPipe. RealPipe optimizes given water network distribution systems by considering capital cost of pipes only. Five operators are involved in the program algorithm. These operators are generation, selection, elitism, crossover and mutation. Optimum population size is found to be between 30-70 depending on the size of the network (i.e. pipe number) and number of commercially available pipe size. Elitism rate should be around 10 percent. Mutation rate should be selected around 1-5 percent depending again on the size of the network. Multipoint crossover and higher rates are advisable. Also pressure penalty parameters are found to be much important than velocity parameters. Below pressure penalty parameter is the most important one and should be roughly 100 times higher than the other. Two known networks of the literature are examined using RealPipe and expected results are achieved. N8.3 network which is located in the northern side of Ankara is the case study. Total cost achieved by RealPipe is 16.74 percent lower than the cost of the existing network / it should be noted that the solution provided by RealPipe is hydraulically improved.

Errata sheet pasted onto front end-paper. / Bibliography: leaves 357-377. / xxvi, 514 leaves : ill. (some col.), fold. maps ; 30 cm. / Title page, contents and abstract only. The complete thesis in print form is available from the University Library. / Thesis (Ph.D.)--University of Adelaide, Dept. of Civil and Environmental Engineering, 1999?

In most of the urban cities of developing countries piped water supply is intermittent and they receive water on alternate days for about few hours. The Unaccounted For Water (UFW) in these cities is very high due to aged infrastructure, poor management and operation of the system. In the cities of developing countries, supplied water is not able to meet the demand and there is huge gap between supply and demand of water. To meet the water demand people are depending on other sources of water like groundwater, rain water harvesting, waste water treatment, desalination etc. Huge quantity of groundwater is extracted without any account for the quantity of water used. The main challenge for water authorities is to meet the consumer demands at varying loading conditions. However, the present execution of decisions in the operational management of WDS is through manual control. The manual control of valve throttling and control of pump speed, reduces the efficiency and operation of WDS. In such cases, system modeling coupled with automated control can play a significant role in the appropriate execution and operation of the system. In the past few decades, there has been a major development in the field of modeling and analysing water distribution systems. Most of the people in Indian mega cities are facing water problems as they are not able to receive safe reliable drinking water. In rapidly growing cities, the water resources management has been a major concern for the Government. There is always a need to optimize the available water resources when the rate of demand constantly beats the rate of replenishments. Mathematical modeling of WDS has become an indispensible tool since the ages to model any type of WDS. Development of mathematical models of WDS is necessary to analyse the system behavior for a wide range of operating conditions. Using models, problems can be anticipated in proposed or existing systems, and solutions can be evaluated before time, money, and materials are invested in a real-world project. In the present study, we have developed a model of WDS of a typical city like Bangalore, India and analysed them for several scenarios and operating conditions. Bangalore WDS is modeled using EPANET. Before a network model is used for analysis purpose, it must be ensured that the model is predicting the behavior of the system with reasonable accuracy. The process of matching the parameters of the developed model and the field observed data is known as calibration. All WDS require calibration for effective modeling and simulation of the system. Demand and roughness are the most uncertain parameters and they are adjusted repeatedly to get the required head at nodes and flow in the pipes. The calibration parameters usually include pipe roughness, valve settings, pipe diameter and demand. Pipe roughness, valve settings and pipe diameter are associated with the flow conditions and the demands relate to the boundary conditions. For Bangalore WDS, the values of roughness coefficient and demand are available; and the values of valve settings are not available. Hence, this value is estimated during calibration process. Dynamic Inversion (DI) nonlinear controller with Proportional Integral Derivative (PID) features (DI-PID) is used for calibrating WDS for valve settings on the basis of observed flow and roughness coefficient. From the obtained results it is observed that, controllers are capable of achieving the target flow to all the GLRs with acceptable difference between the flow meter readings and the simulated flow. After calibrating any real WDS to the field observed data, it will be useful for water authorities if the consumer demands are met up to certain extent. This can be achieved by using the concept of equitable distribution of water to different consumers. In the urban cities of developing countries, often large quantities of water are supplied to only a few consumers, leading to inequitable water supply. It is a well known fact that quantity of water supplied from the source is not distributed equitably among the consumers. Aged pipelines pump failures, improper management of water resources are some of the main reasons for it. Equitable water to different consumers can be provided by operating the system in an efficient manner. Most of the urban cities receive water from the source to intermediate reservoirs and from these reservoirs water is supplied to consumers. Therefore, to achieve equitable water supply, these two supply levels have to be controlled using different concepts/ techniques. The water requirement of each of the reservoirs has to be calculated, which may depend on the number of consumers and consumer category. Each reservoir should receive its share of water to satisfy its consumer demand and also there must be provision to accommodate shortages, if any. The calibrated model of Bangalore WDS is used to achieve equitable water supply quantity to different zones of Bangalore city. The city has large undulating terrain among different zones which leads to unequal distribution of water. Dynamic Inversion (DI) nonlinear controller with Proportional Integral Derivative (PID) features (DI-PID) is used for valve throttling to achieve the target flows to different zones/reservoirs of the city at different levels. Equitable water distribution to different reservoirs, when a part of the source fails to supply water is also discussed in this thesis. From the obtained results it is observed that, controllers were responding in all the cases in different levels of targets for such a huge network. When there is change in supply pattern to achieve the equitable supply of water to different zones, the hydraulics of the WDS will change. Therefore, it is necessary to understand whether the system is able to handle these changes. The concept of reliability can be used to analyse the performance of WDS for wide range of operating conditions. Reliability analysis of a WDS for both normal and likely to occur situations will give a better quality of service to its consumers. Calculating both hydraulic and mechanical reliability is important as the chances of occurrence of both the failure scenarios are equal in a WDS. In the present study, a methodology is presented to model the nodal, system and total reliability for water supply networks by considering the hydraulic and mechanical failure scenarios. These two reliability measures together give the total reliability of the system. Analysing a real and complex WDS for the probable chances of occurrence of the failure scenarios; and then to anlyse the total reliability of the system is not reported in the literature and this analysis is carried out in the present study for Bangalore city WDS. The hydraulics of the system for all the operating conditions is analysed using EPANET. Hydraulic reliability is calculated by varying the uncertain independent parameters (demand, roughness and source water) and mechanical reliability is calculated by assuming system component failures. The system is analysed for both the reliability scenarios by considering different chances of failure that may occur in a real WDS; and hence the total reliability is calculated by making different combinations of hydraulic and mechanical failure scenarios. Sensitivity analysis for all the zones is also carried out to understand the behavior of different demand points for large fluctuation in hydraulics of the system. From the study, it is observed that, Hydraulic reliability decreases as the demand variation increases. But, as the roughness variation increases, there is no much change in the nodal or system reliability. Consumer demand or reliability of the WDS can be increased by saving the water lost in the system. This can be achieved by tracking the water parcel from the source till the consumer end, which will give an idea about the performance of different stages and zones in achieving the target flows. Huge quantity of water is lost in WDS and hence it is necessary to account for the water lost at different levels, hence the system can be managed in a better way. In most of the intermittent water supply systems demand is controlled by supply side; there is also a need to understand the demand variation at the consumer end which in turn affects the supply. Matching this varied supply-demand gap at various levels is challenging task. To get a better control of such problem, water balance (WB) equations need to be derived at various levels. When we derive these WB equations it should be emphasized that UFW is one of the major component of this equation. Given this back ground of the complex problem, for a typical city like Bangalore, an attempt is made to derive WB equations at various levels. In the present study, stage-wise and zone-wise WB is analysed for different months based on the flow meter readings. The conceptual model developed is calibrated, validated and also the performance of the model is analysed by giving a chance of error in the flow measurement. Based on all the above observations, stage-wise and zone-wise water supply weights are also calculated. From the study it is found that, there is no much loss of water in all the four stages of supply. Water loss is minimal of about 3 % till water reaches from source to GLRs. Water is transferred between the stages during some days of the month, may be due to shortage of water or due to unexpected demand. Huge quantity of water is lost in the distribution main which is of about 40 to 45% for all the moths which is analysed. This type of model will be extremely useful for water supply managers to manage their resources more efficiently and this study is discussed in detail as a part of this thesis. As mentioned above, huge quantity of groundwater is used in urban cities and the quantity of water extracted is not accounted. In the present study, zone wise and sub zone-wise piped water and ground water used in different parts of the cities is analysed with the help of available data. From the study it is observed that, the quantity of piped water supply and UFW is consistent for the time period analysed and the quantity of water withdrawn from the borewells are varying considerably depending on the yield of the borewlls in different zones. The main components of urban water supply are piped water, ground water, rainfall and runoff generated, UFW, waste water produced and other water quantities which may be minute. In future, to manage the water resources properly, integrated water management is necessary in city scale which will give an idea about the total water produced and the water utilized at the consumer end. Therefore, integrated water management concept is carried out in Hebbal region, (a small part of Bangalore) using the available data. From the analysis we noticed that, domestic water supplied to North sub zones are better when comparing to East sub zones. This type of total water balance can be studied in other parts of Bangalore, to understand the behavior of different water components and to make better decisions. The developed model, analysis and operating conditions of this study can be applied to other similar cities like Bangalore. This type of study may be useful to water authorities for better control of the resources, or in making better decisions and these types of models will act as decision support systems.

Management and supply of water in an urban water distribution system is a complex process, which include various complexities like pressure variations across the network depending on topography, demand variations depending on customers’ requirement and unaccounted water etc. Applying automatic control methods to water distribution systems is a way to improve the management of water distribution. There have been some attempts in recent years to develop optimal control algorithms to assist in the operation of complex water distribution systems. The difficulties involved by these hydraulic systems such as non-linearity, and diurnal demand patterns make the choice of a suitable automatic control method a challenge. For this purpose, this study intends to investigate the applicability of different controllers which would be able to meet the targets as quickly as possible and without creating undue transients. As a first step towards application of different controllers, PD and PID linear controllers have been designed for pump control and valve control in water distribution systems. Then a Dynamic Inversion based nonlinear controller has been designed by considering the non-linearities in the system. Here, different cases considering the effects of initial conditions used, linearization methods used, time step used for integration and selection of gains etc., have been studied before arriving at best controller. These controllers have been designed for both the flow control problems and level control problems. It is found that Dynamic Inversion-based nonlinear controller outperforms other controllers. It is well known that the performance of controllers is much dependent on the tuning of the gains (parameters). Thus in this study various alternative techniques such as Ziegler--Nichols rules (ZNPID), Genetic algorithms (GAPID) and fuzzy algorithms (FZPID) have been studied and a comparative study has been made Although with all the three gain tuning methods, required states have reached their target values, but the responses vary much in reaching to final targets. The self-tuned FZPID controller outperforms other two controllers, especially with regard to overshoots and the time taken to tune the gains for each problem. Further, an optimal DI controller is developed for the over determined case with more controls and less targets. Energy loss is considered as an objective function and normal DI controller equations are considered as constraints. Hence, an attempt is made to reduce the energy minimization in water distribution system by formulating an optimal control problem using optimal Dynamic Inversion concept. Finally, leakage reduction model is developed based on excessive pressure minimization problem by locating valves optimally as well as by setting valves optimally. For this purpose, optimization problem is solved using Pattern search algorithms and hydraulic analysis is carried out using EPANET program.

Water distribution network models are widely used for various purposes such as long-range planning, design, operation and water quality management. Before these models are used for a specific study, they should be calibrated by adjusting model parameters such as pipe roughness values and nodal demands so that models can yield compatible results with site observations (basically, pressure readings). Many methods have been developed to calibrate water distribution networks. In this study, Darwin Calibrator, a computer software that uses genetic algorithm, is used to calibrate N8.3 pressure zone model of Ankara water distribution network / in this case study the network is calibrated on the basis of roughness parameter, Hazen Williams coefficient for the sake of simplicity. It is understood that there are various parameters that contribute to the uncertainties in water distribution network modelling and the calibration process. Besides, computer software&rsquo / s are valuable tools to solve water distribution network problems and to calibrate network models in an accurate and fast way using automated calibration technique. Furthermore, there are many important aspects that should be considered during automated calibration such as pipe roughness grouping. In this study, influence of flow velocity on pipe roughness grouping is examined. Roughness coefficients of pipes have been estimated in the range of 70-140.

This diploma thesis describes study of interconnection of Letohrad and Lanškroun water distribution systems. The thesis contains an overview of legislative regulations and technical standards related to the construction, design and directional solution of water supply systems. Following that, there is the description of the current state of the affected water mains. Next part is the design of interconnection including hydraulic analysis in using Epanet 2.0 software. The study contains several variants of the solution. The economic assessment is included.

Electrical energy has become a very important and integrated part of the current era. Electricity cost saving interventions, such as load shifting, form part of demand side management (DSM) interventions. DSM interventions have been successfully implemented in the past to ensure reliable supply of electricity during the Eskom peak periods. It has been established that there is a need to implement an electricity cost saving intervention on a large water distribution utility. This dissertation focuses on the integration of electricity cost saving interventions on a water distribution utility. An investigation methodology, as well as an integration strategy for implementing an electricity cost saving intervention were developed. This study expands on the importance of an integrated approach. It further discusses the shortcomings of the current control philosophies of a large water distribution utility in South Africa. A load shifting project was implemented as an electricity cost saving intervention on a large water distribution utility in South Africa. The proposed integrated strategy was simulated and an optimised approach developed. It was found that the implementation of the strategy was limited due to process constraints and increasing water demand. Utilising the large combined installed capacity of the pumps in the water distribution utility and the storage capacity, the strategy was implemented and cost savings obtained. It was concluded that load shifting was possible on individual pumping stations in the water distribution utility subsystems, and could, therefore, be quantified to an integrated approach. / MIng (Mechanical Engineering), North-West University, Potchefstroom Campus, 2015