The objective of this study was to examine the influence of nutrients on the biological phosphorus removal process at high acetate concentrations. It was an extension of studies conducted by Randall and Chapin (1994), who found that industrial wastewater with high concentrations of acetate were able to inhibit the biological phosphorus removal process. Two bench-scale pilot plants were operated under controlled conditions that included synthetic wastewater as feed. The acetic acid concentrations in the feed of one system was increased in steps from 200 to 800 mg/L while the acetic acid concentrations in the feed of the other system was constantly held at 200 mg/L. Sludge from both systems was used for batch tests determining the kinetics of phosphorus release and uptake and poly-β-hydroxybutyric acid synthesis. Furthermore, the influence of various nutrients were examined during these batch tests. The results of this study confirmed the observations of Randall and Chapin (1994). High concentrations (600 mg/L) of acetic acid did inhibit the biological phosphorus removal process; however, this inhibition could be countered by adding calcium into the feed. The reactions of phosphorus release and uptake are described by first order kinetics. / Master of Science

Granular activated carbon (GAC) pretreatment was evaluated for the removal of trihalomethane (THM) precursors from a surface water supply, the Occoquan Reservoir, in northern Virginia. The carbon contactors were operated in the upflow mode at flow rates of 2, 4, and 6 gpm which provided empty bed contact times (EBCT) of 26, 13, and 6.6 minutes, respectively. Reservoir raw water quality data was collected to determine what relationship existed between these measurements and the trihalomethane formation potential (THMFP) of the reservoir water. The results indicated that THM precursors, as measured by total organic carbon (TOC) and THMFP, could be removed from an untreated surface water supply by GAC contact. The degree to which THM precursors were removed was directly related to EBCT, the most effective being 26 minutes (2 gpm). GAC contact appeared to be selective for the removal of those precursors responsible for instantaneous THM concentrations i.e., those produced within a thirty minute chlorine-contact period. Those precursors responsible for THM concentrations produced after thirty minutes and for up to seven days thereafter (herein designated THMFP) appeared to be associated either with particulate matter in the raw water or with larger molecular weight organic substances which were not well adsorbed by the carbon. There were no discernible direct correlations between THMFP and the turbidity, color, TOC, chlorophyll-a concentration and algal populations in the raw water. Runoff from a rainstorm late in the period of study resulted in increases in raw water color, turbidity, and TOC concentrations, but it was impossible to determine which of these factors was responsible for the increased raw water THMFP that occurred at the same time. / Master of Science

This study evaluated alternatives to continuously regenerated greensand for iron and manganese removal. Specific objectives were (1) to investigate the applicability for removing soluble manganese by adsorption and oxidation onto the surface of manganese oxide-coated media, and (2) to develop mathematical models to predict the removal of soluble manganese both in the presence and absence of free chlorine. Results from a pilot-scale experiment in Columbus, Indiana, showed that when the filters were operated in a conventional oxidant addition mode (i.e., with the addition of HOCI and KMnO₄) the anthracite-sand and anthracite-sand-garnet configurations both provided efficient treatment because of the reduced rate of head loss. Further experiments, without the use of KMnO₄ or greensand, equally removed manganese by adsorption and oxidation onto oxide-coated media; however, the treatment process resulted in reduced head loss and oxidant costs. Results from this study and other previous research demonstrated that manganese removal by oxide coatings is an efficient and functional treatment mechanism. However, little quantitative information was available to predict these processes. Therefore, mathematical models were developed to help predict design and operational conditions needed to implement oxide-coated media as a treatment process. Two separate models were developed to predict (1) the continuous removal of soluble manganese in the presence of free chlorine (continuous regeneration model), and (2) the eventual breakthrough of soluble manganese without oxidant addition (intermittent regeneration model). Each model was derived from chemical reaction, mass balance, or isotherm equations and was further developed by a sensitivity analysis and parameter estimation. The two models were then verified by predicting manganese removal from independent research. The continuous regeneration model can help predict the removal of soluble manganese by adsorption and oxidation on the surface of oxide-coated media and is useful in the design of filters for continuous Mn(Il) removal. The intermittent regeneration model effectively predicts the performance of filters without the addition of an oxidant and is useful for treatment plants which cannot apply chlorine continuously to their filter applied water. / Master of Science

No description available.

No description available.

No description available.

Wong Man Yung. / Thesis (M.Phil.)--Chinese University of Hong Kong, 2006. / Includes bibliographical references (leaves 106-120). / Abstracts in English and Chinese. / Acknowledgements --- p.i / Abstract --- p.ii / Table of Contents --- p.vi / List of Figures --- p.xi / List of Plates --- p.xiii / List of Tables --- p.xv / Abbreviations --- p.xvi / Equations --- p.xviii / Chapter 1. --- Introduction --- p.1 / Chapter 1.1 --- Water disinfection --- p.1 / Chapter 1.2 --- Bacterial species --- p.2 / Chapter 1.2.1 --- Staphylococcus saprophyticus --- p.2 / Chapter 1.2.2 --- Enterobacter cloacae --- p.3 / Chapter 1.3 --- Disinfection methods --- p.4 / Chapter 1.3.1 --- Physical methods --- p.4 / Chapter 1.3.1.1 --- UV-C irradiation --- p.4 / Chapter 1.3.1.2 --- Solar disinfection --- p.5 / Chapter 1.3.2 --- Chemical methods --- p.6 / Chapter 1.3.2.1 --- Chlorination --- p.6 / Chapter 1.3.2.2 --- Ozonation --- p.7 / Chapter 1.3.2.3 --- Mixed disinfectants --- p.8 / Chapter 1.3.3 --- Other disinfection methods --- p.8 / Chapter 1.4 --- Advanced oxidation processes (AOPs) --- p.9 / Chapter 1.5 --- Photocatalytic oxidation (PCO) --- p.10 / Chapter 1.5.1 --- PCO process --- p.12 / Chapter 1.5.2 --- Photocatalysts --- p.14 / Chapter 1.5.2.1 --- Titanium dioxide (P25) --- p.15 / Chapter 1.5.2.2 --- Silver sensitized P25 (Ag/P25) --- p.16 / Chapter 1.5.2.3 --- Silicon dioxide doped titanium dioxide (SiO2-TiO2) --- p.17 / Chapter 1.5.2.4 --- Copper(I) oxide sensitized P25 (Cu2O/P25) --- p.18 / Chapter 1.5.3 --- Irradiation sources --- p.19 / Chapter 1.5.4 --- PCO disinfection mechanisms --- p.20 / Chapter 1.6 --- Bacterial defense mechanisms against oxidative stress --- p.22 / Chapter 2. --- Objectives --- p.25 / Chapter 3. --- Materials and Methods --- p.26 / Chapter 3.1 --- Chemicals --- p.26 / Chapter 3.2 --- Bacterial culture --- p.26 / Chapter 3.3 --- Photocatalytic reactor --- p.27 / Chapter 3.4 --- PCO efficacy test --- p.30 / Chapter 3.5 --- Optimization of PCO conditions --- p.31 / Chapter 3.5.1 --- Effect of P25 concentrations --- p.31 / Chapter 3.5.2 --- Effect of UV intensities --- p.32 / Chapter 3.5.3 --- Combinational study of P25 concentrations and UV intensities --- p.32 / Chapter 3.5.4 --- Effect of stirring rates --- p.32 / Chapter 3.5.5 --- Effect of initial cell concentrations --- p.33 / Chapter 3.6 --- PCO disinfection using different photocatalysts --- p.33 / Chapter 3.6.1 --- Effect of CU2O/P25 concentrations --- p.33 / Chapter 3.6.2 --- Effect of CU2O powder on the two bacterial species --- p.33 / Chapter 3.7 --- Transmission electron microscopy (TEM) --- p.34 / Chapter 3.8 --- Catalase (CAT) test --- p.37 / Chapter 3.9 --- Superoxide dismutase (SOD) activity assay --- p.39 / Chapter 4. --- Results --- p.40 / Chapter 4.1 --- Efficacy test --- p.40 / Chapter 4.2 --- PCO disinfection under UV irradiation --- p.40 / Chapter 4.2.1 --- Control experiments --- p.40 / Chapter 4.2.2 --- Optimization of PCO conditions using P25 as a photocatalyst --- p.42 / Chapter 4.2.2.1 --- Effect of P25 concentrations --- p.42 / Chapter 4.2.2.2 --- Effect of UV intensities --- p.45 / Chapter 4.2.2.3 --- Combinational study of P25 concentrations and UV intensities --- p.48 / Chapter 4.2.2.4 --- Effect of stirring rates --- p.54 / Chapter 4.2.2.5 --- Effect of initial cell concentrations --- p.57 / Chapter 4.2.3 --- Comparison of PCO inactivation efficiency between S. saprophyticus and E. cloacae --- p.60 / Chapter 4.2.4 --- PCO disinfection using different photocatalysts --- p.62 / Chapter 4.2.4.1 --- Control experiments --- p.62 / Chapter 4.2.4.2 --- Ag/P25 --- p.62 / Chapter 4.2.4.3 --- SiO2-TiO2 --- p.64 / Chapter 4.2.4.4 --- Cu2O/P25 --- p.64 / Chapter 4.3 --- PCO disinfection under visible light irradiation --- p.66 / Chapter 4.3.1 --- Effect of Cu2O/P25 concentrations --- p.67 / Chapter 4.3.2 --- Effect of CU2O powder on the two bacterial species --- p.70 / Chapter 4.4 --- Feasibility use of indoor light (fluorescent lamps) for PCO disinfection --- p.71 / Chapter 4.5 --- Transmission electron microscopy (TEM) --- p.74 / Chapter 4.5.1 --- Morphological changes induced by PCO using P25 as a photocatalyst --- p.74 / Chapter 4.5.2 --- Morphological changes induced by PCO using Cu2O/P25 as a photocatalyst --- p.77 / Chapter 4.6 --- Catalase (CAT) test --- p.80 / Chapter 4.7 --- Superoxide dismutase (SOD) activity assay --- p.82 / Chapter 5. --- Discussion --- p.83 / Chapter 5.1 --- Efficacy test --- p.83 / Chapter 5.2 --- PCO disinfection under UV irradiation --- p.83 / Chapter 5.2.1 --- Optimization study --- p.84 / Chapter 5.2.1.1 --- Effect of P25 concentrations --- p.84 / Chapter 5.2.1.2 --- Effect of UV intensities --- p.85 / Chapter 5.2.1.3 --- Combinational study of P25 concentrations and UV intensities --- p.86 / Chapter 5.2.1.4 --- Effect of stirring rates --- p.86 / Chapter 5.2.1.5 --- Effect of initial cell concentrations --- p.87 / Chapter 5.2.2 --- Comparison of PCO inactivation efficiency between S. saprophyticus and E. cloacae --- p.88 / Chapter 5.2.3 --- PCO disinfection using different photocatalysts --- p.89 / Chapter 5.2.3.1 --- Ag/P25 --- p.89 / Chapter 5.2.3.2 --- SiO2-TiO2 and Cu2O/P25 --- p.90 / Chapter 5.3 --- PCO disinfection under visible light irradiation --- p.90 / Chapter 5.3.1 --- Effect of Cu20/P25 concentrations --- p.91 / Chapter 5.3.2 --- Effect of CU2O powder on the two bacterial species --- p.92 / Chapter 5.4 --- Feasibility use of fluorescent lamps for PCO disinfection --- p.93 / Chapter 5.5 --- Transmission electron microscopy (TEM) --- p.95 / Chapter 5.5.1 --- Morphological changes induced by PCO using P25 as a photocatalyst --- p.95 / Chapter 5.5.2 --- Morphological changes induced by PCO using CU2O/P25 as a photocatalyst --- p.96 / Chapter 5.6 --- Catalase (CAT) test --- p.98 / Chapter 5.7 --- Superoxide dismutase (SOD) activity assay --- p.99 / Chapter 6. --- Conclusion --- p.101 / Chapter 7. --- References --- p.106 / Chapter 8. --- Appendix --- p.121

Orientador: Ruben Bresaola Junior / Dissertação (mestrado) - Universidade Estadual de Campinas, Faculdade de Engenharia Civil, Arquitetura e Urbanismo / Made available in DSpace on 2018-08-17T00:58:33Z (GMT). No. of bitstreams: 1 Lima_MilmaRozade_M.pdf: 5486982 bytes, checksum: f022781b42a125131286f8b2864cc00b (MD5) Previous issue date: 2010 / Resumo: A floculação em meio granular fixo desperta bastante interesse por suas possibilidades de aplicação, principalmente em estações de tratamento de água de pequeno porte (vazões menores que 10 L.s-1), devido à sua eficiência, compacidade e baixo custo. No entanto, o reduzido volume de vazios proporcionado pelo meio granular quando comparado ao dos materiais sintéticos favorece o aumento excessivo da perda de carga imposta ao escoamento e consequentemente o inconveniente de freqüentes necessidades de limpeza. Diante da necessidade de atenuar ou mesmo eliminar tais considerações operacionais, este trabalho propõe estudos comparativos de eficiência de floculação hidráulica em meios granulares fixos em sistemas pilotos constituídos por seixos rolados de diferentes granulometrias e outro por manta não tecida (PP) e esferas sólidas (? 9 mm, PS). Os ensaios foram realizados com água coagulada da ETA Bragança Paulista (SABESP) para taxas de aplicação superficial de 50, 75, 100, 150, 180, 200, 250, 300 e 350 m3.m-2.dia-1, onde foram determinadas as condições operacionais, o período de floculação e a evolução da perda de carga total. Os resultados mostraram que a porosidade mais elevada apresentada pelo sistema piloto constituído de manta sintética e esferas sólidas favoreceu o aumento da taxa de colisões entre as partículas coloidais, o que permitiu a geração de manta de lodo, a formação de escoamento laminar, bem como, a facilidade de liberação do lodo retido para recuperação da carga hidráulica disponível / Abstract: The flocculation in fixed granular media arises plenty of interests in its possibility of applying, mainly in the water treatment plants of small size (flow less than 10 L.s-1), due to its efficiency, compactness and low cost. Nevertheless the reduced volume of voids provided by granular media as compared to the synthetic materials, collaborates to the excessive increasing of head loss imposed to the flowing off and consequently the inconvenient of frequent needs of cleaness. Before the need of reduction or even elimination of the such operational considerations, this work suggests comparative studies of the hydraulic flocculation efficiency by fixed granular media in the pilot systems composed by the stones from different granulametries or another one by non woven synthetic fabric (PP) and solid spheres (? 9mm, PS). The tests have been made with coagulated water from ETA Bragança Paulista (SABESP) to superficial applying rates of 50, 75, 100, 150, 180, 200, 250, 300 and 350 m3.m-2.dia-1, where they were determined the working conditions, flocculation time and evolution of head loss. The results have shown that the most elevated porosity presented in the pilot system composed by non woven synthetic fabric and solid spheres collaborated to the increasing of the collision rates among the particles, which allowed the generation of sludge blanket, the formation of laminar flow such as the facility of discharging of retained sludge for recovery of the hydraulic load available / Mestrado / Saneamento e Ambiente / Mestre em Engenharia Civil

Orientador: Ruben Bresaola Junior / Dissertação (mestrado) - Universidade Estadual de Campinas, Faculdade de Engenharia Civil, Arquitetura e Urbanismo / Made available in DSpace on 2018-08-05T11:49:09Z (GMT). No. of bitstreams: 1 Marmo_CarlosRenato_M.pdf: 2657579 bytes, checksum: 5995fb2c9ebb8d2a626b9bc6f6ec4b0f (MD5) Previous issue date: 2005 / Resumo: A presente pesquisa avaliou, em escala de laboratório, a formação de trihalometanos (THM) produzidos em reações de oxidação, com cloro livre, de amostras de água contendo ácidos húmicos, sob diferentes concentrações e tempos de contato. O estudo também abrangeu a presença do íon brometo, como forma de se avaliar, qualitativa e quantitativamente, as diferentes espécies de THM produzidas. A detecção dos trihalometanos formados foi realizada, comparativamente, através de duas técnicas analíticas. A cromatografia gasosa, indicada para a análise de tais moléculas, permitiu a quantificação dos compostos clorofórmio, diclorobromometano, dibromoclorometano e bromofórmio. A espectrofotometria foi avaliada como metodologia alternativa à primeira, permitindo a expressão dos resultados apenas em THM totais. Foram realizados ensaios de remoção de THM por adsorção em diferentes concentrações de carvão ativado em pó (CAP), seguido de processos de coagulação com sulfato de alumínio, floculação, sedimentação e filtração, em reatores estáticos. Os resultados obtidos indicaram que a formação de THM é diretamente proporcional às concentrações de cloro, ácidos húmicos, íon brometo e ao tempo de contato das reações. Os procedimentos de adsorção em CAP, seguido de processos convencionais de tratamento de água, demonstraram remoções de THM das amostras da ordem de até 89%. O aumento da concentração de CAP de 10 para 150 mg/L, e do tempo de contato de adsorção de 60 para 120 minutos, contribuiu para os melhores desempenhos nos experimentos realizados. As técnicas de detecção de THM por cromatografia gasosa e por espectrofotometria apresentaram resultados diferentes nas condições destes ensaios / Abstract: The present research evaluated, in laboratory scale, the formation of trihalomethanes (THM) produced in oxidation reactions, with free chlorine, of water samples with humic acids, in different concentrations and reaction time. This research also studied the presence of the bromide ion, to evaluate, qualitatively and quantitatively, the different species of THM produced. Trihalomethanes detection was comparatively investigated through two analytical techniques. The gaseous chromatography, indicated for the analysis of such molecules, resulted in the quantification of chloroform, dichlorobromomethane, dibromochloromethane and bromoform. The spectrophotometric technique was evaluated as an alternative methodology to the first one, allowing the expression of the results only in total THM. Static reactors were used to carry out assays of THM removal by adsorption in different concentrations of powdered activated carbon (PAC), followed by coagulation processes with aluminium sulphate, flocculation, sedimentation and filtration. The results indicated that THM formation is directly proportional to the concentrations of chlorine, humic acids, bromide ion and reaction time. The procedure of PAC adsorption, followed by conventional processes of water treatment were effective, showing THM removal from the samples of up to 89%. The increase in PAC concentration from 10 to 150 mg/L, and adsorption reaction time from 60 to 120 minutes, resulted in the best performances. The methodologies for THM based on gaseous chromatography and espectrophotometric presented different results in the laboratory conditions of these assays / Mestrado / Saneamento e Ambiente / Mestre em Engenharia Civil

Orientador: Ruben Bresaola Junior / Dissertação (mestrado) - Universidade Estadual de Campinas, Faculdade de Engenharia Civil, Arquitetura e Urbanismo / Made available in DSpace on 2018-08-11T19:59:18Z (GMT). No. of bitstreams: 1 Santos_BrunoVicentedeAzevedoPereirados_M.pdf: 1399208 bytes, checksum: e6e631ee616dacba62ad54d7e6050502 (MD5) Previous issue date: 2005 / Resumo: A presente pesquisa teve por objetivo analisar a formação de THM através do uso de permanganato de potássio, de forma isolada ou associada com o cloro livre, no processo de pré-oxidação, e, numa segunda etapa, avaliar a eficiência de remoção destes subprodutos através da adsorção em carvão ativado em pó seguida de tratamento convencional. Foram realizadas oxidações de soluções contendo ácidos húmicos e brometos, em diversas dosagens, analisando-se a formação de THM por espectrofotometria e cromatografia gasosa. A remoção dos subprodutos formados foi realizada com dosagens de CAP variando de 10,0 a 150,0 mg/L e com dosagem de coagulante e valor de pH determinados experimentalmente para cada uma delas. Os resultados obtidos, pelos dois métodos de detecção, mostraram que não houve formação significativa de THM quando a oxidação foi realizada apenas pelo permanganato de potássio e que, com o uso conjunto dos dois oxidantes, houve uma redução média de 30 % na formação quando comparada ao uso exclusivo de cloro livre. O processo de tratamento se mostrou eficiente para as dosagens mais altas de CAP, adequando a qualidade da água final nas normas vigentes. / Abstract: The present research had for objective to analyze the formation of THM through the use of potassium permanganate, isolated or associate with free chlorine, in the process of pre-oxidation, and, in a second stage, to evaluate the removal efficiency of these by-products through the adsorption in powdered activated carbon followed by conventional treatment. The oxidations of solutions contend humic acids and bromides, in diverse dosages had been carried through, analyzing the formation of THM with spectrofotometric and gas chromatography methods. The removal of by-products was carried through with dosages of PAC between 10,0 and 150,00 mg/L and dosages of coagulant and pH value determined experimentally for each one of them. The gotten results, for the two methods of determination, had shown that there wasn't significant formation of THM when the oxidation was carried through only by the potassium permanganate and that, with the joint use of the two oxidants, it had an average reduction of 30 % in the formation when compared with the exclusive use of free chlorine use. The treatment process showed efficient for the highest dosages of PAC, adjusting the quality of the final water in the effective regulations. / Mestrado / Saneamento e Ambiente / Mestre em Engenharia Civil