A 6082 aluminium alloy has been characterized with regard to the influence of surface roughness on fatigue strength. Fatigue life testing of smooth specimens was used to establish reference curves for the material in extruded and forged T6 condition. The extruded material was found to have better fatigue strength than the forged material, although the cyclic stress-strain response was similar for both. The forged material was tested in T5, T6 and T7 tempers, showing no significant difference in fatigue strength. Surface roughness was created by circumferential grinding of cylindrical test specimens, and the surface topography was measured using a white light interferometry microscope. The measurements proved to be accurate, although errors were observed for certain surface features. Residual stresses were quantified by X-ray diffraction. Compressive residual stresses of around 150 MPa were found in both rough and smooth specimens. Load cycling did not significantly alter the surface residual stresses. Stress solutions ahead of all major surface grooves were found using a linear elastic material model. Estimates of cyclic stresses and strains were calculated in the notch roots using different Neuber corrections of the linear solution. The results were compared to finite element analysis employing a bilinear kinematic hardening model. A generalized version of the Neuber correction was found to be within 20% of the nonlinear finite element results. Several empirical models for the notch sensitivity factor were investigated. These were found to be unable to describe the notch influence on fatigue life and initiation life. In order to follow this approach, it was recommended that different test specimens should be used where the short fatigue crack growth could be monitored. It was shown that microstructural fracture mechanics theories could be used to estimate the fatigue limit of rough surfaces. In some cases, initiation from material defects or weaknesses would override the influence of surface geometry. In one specimen, the initiation appeared to have started as at a de-bonded grain, while in other cases, initiation was thought to have started at larger second phase particles embedded in notch roots. Further work in this area should focus on statistical descriptions of surface roughness, inherent material defects, and their interaction.

No presente trabalho é apresentada uma nova abordagem para medida de potenciais em altos níveis de tensão que utilizam sensores eletro-ópticos Pockels. Também descreve a aplicação da técnica de interferometria de luz branca em sistemas de alta tensão por fibras ópticas. Neste sistema a informação é codificada no espectro da luz, permitindo assim que a medida seja independente da potência óptica transmitida pelo link de fibras ópticas. Um protótipo foi construído e testado sob excitação de tensão a.c. até 20 kV em 60 Hz mostrando boa resposta e demonstrando a viabilidade deste método. / A new approach to perform measurement of potentials in high voltage levels using electrooptical Pockels sensors is presented here. This work describes an application of the White Light Interferometry technique to a high voltage optical fiber measurement system. In this system the information is encoded in the spectrum of the light, allowing the measurement to be independent of the optical power transmitted by the optical fiber link. A prototype was built and tested under excitation of a.c. voltages up to 20 kV in 60 Hz showing good response and demonstrating the feasibility of this method.

No presente trabalho é apresentada uma nova abordagem para medida de potenciais em altos níveis de tensão que utilizam sensores eletro-ópticos Pockels. Também descreve a aplicação da técnica de interferometria de luz branca em sistemas de alta tensão por fibras ópticas. Neste sistema a informação é codificada no espectro da luz, permitindo assim que a medida seja independente da potência óptica transmitida pelo link de fibras ópticas. Um protótipo foi construído e testado sob excitação de tensão a.c. até 20 kV em 60 Hz mostrando boa resposta e demonstrando a viabilidade deste método. / A new approach to perform measurement of potentials in high voltage levels using electrooptical Pockels sensors is presented here. This work describes an application of the White Light Interferometry technique to a high voltage optical fiber measurement system. In this system the information is encoded in the spectrum of the light, allowing the measurement to be independent of the optical power transmitted by the optical fiber link. A prototype was built and tested under excitation of a.c. voltages up to 20 kV in 60 Hz showing good response and demonstrating the feasibility of this method.

This thesis is specialized on composition of workplace for experiments flowing from optical interferometry. Here are described laboratory exercise servant for demonstration basic principles of interferometry. In more details is described method measurement of height profile objects with method white light interferometry.

No description available.

O trabalho tem por objetivo o estudo e o desenvolvimento de interferômetros recuperadores com baixa tensão de meia onda utilizando moduladores eletro-ópticos para serem aplicados em sistemas Interferométricos de luz branca. Ele dá continuidade às pesquisas do autor em seu mestrado, em que foi desenvolvido e testado um sistema de sensoriamento eletro-óptico capaz de medir diretamente tensões de até 69,4 kVRMS. Desta forma aperfeiçoa-se o sistema de processamento de sinais ópticos desenvolvendo um novo interferômetro recuperador, baseado em óptica integrada. Para o desenvolvimento do tema proposto, inicialmente foi feito uma revisão da literatura/bibliografia, baseada em livros, artigos e teses, visando identificar o \"estado da arte\" relacionado aos moduladores eletro-ópticos para definir o tipo de modulador mais adequado à aplicação em vista. O estudo resultou na escolha de um componente em óptica integrada que foi aplicado numa configuração inédita em um protótipo de transformador de potencial óptico para medição de elevados níveis de tensão elétrica. As características de desempenho deste protótipo foram comparadas com as do protótipo previamente construído. Como resultado deste trabalho, amplia-se o conhecimento e fixa-se em âmbito nacional o domínio sobre as técnicas de construção de interferômetros recuperadores baseados em óptica integrada aplicáveis à recuperação de sinais ópticos em sistemas interferométricos para medição de altas tensões. / This work has as objective the study and development of low half-wave voltage recovery interferometers using electro-optical modulators to be applied to white light interferometric systems. This work is a continuation in the research carried out by the author to obtain his master degree, in which it was developed and tested an electro- optic sensing system capable to measure direct voltage to 69.4 kVrms. In the present work the optical signals processing system is improved by developing a new recovery interferometer based on integrated optics. To develop the proposed subject, initially a review of the literature, based on books, articles and thesis, has been done aiming to identify the State of the Art related to electro-optic modulators and helping to define the most suitable type of modulator for the desired application. The study resulted in the selection of an integrated optical device arranged in an unpublished configuration that was applied to a prototype of optical voltage transformer, intended to measure high voltage levels. The performance of this prototype was compared with a previous version. The results of this work increase the knowledge of the construction techniques of recovery interferometers based on integrated optic devices applicable to the recovering of optical signals in interferometric systems for high voltage measurement.

O trabalho tem por objetivo o estudo e o desenvolvimento de interferômetros recuperadores com baixa tensão de meia onda utilizando moduladores eletro-ópticos para serem aplicados em sistemas Interferométricos de luz branca. Ele dá continuidade às pesquisas do autor em seu mestrado, em que foi desenvolvido e testado um sistema de sensoriamento eletro-óptico capaz de medir diretamente tensões de até 69,4 kVRMS. Desta forma aperfeiçoa-se o sistema de processamento de sinais ópticos desenvolvendo um novo interferômetro recuperador, baseado em óptica integrada. Para o desenvolvimento do tema proposto, inicialmente foi feito uma revisão da literatura/bibliografia, baseada em livros, artigos e teses, visando identificar o \"estado da arte\" relacionado aos moduladores eletro-ópticos para definir o tipo de modulador mais adequado à aplicação em vista. O estudo resultou na escolha de um componente em óptica integrada que foi aplicado numa configuração inédita em um protótipo de transformador de potencial óptico para medição de elevados níveis de tensão elétrica. As características de desempenho deste protótipo foram comparadas com as do protótipo previamente construído. Como resultado deste trabalho, amplia-se o conhecimento e fixa-se em âmbito nacional o domínio sobre as técnicas de construção de interferômetros recuperadores baseados em óptica integrada aplicáveis à recuperação de sinais ópticos em sistemas interferométricos para medição de altas tensões. / This work has as objective the study and development of low half-wave voltage recovery interferometers using electro-optical modulators to be applied to white light interferometric systems. This work is a continuation in the research carried out by the author to obtain his master degree, in which it was developed and tested an electro- optic sensing system capable to measure direct voltage to 69.4 kVrms. In the present work the optical signals processing system is improved by developing a new recovery interferometer based on integrated optics. To develop the proposed subject, initially a review of the literature, based on books, articles and thesis, has been done aiming to identify the State of the Art related to electro-optic modulators and helping to define the most suitable type of modulator for the desired application. The study resulted in the selection of an integrated optical device arranged in an unpublished configuration that was applied to a prototype of optical voltage transformer, intended to measure high voltage levels. The performance of this prototype was compared with a previous version. The results of this work increase the knowledge of the construction techniques of recovery interferometers based on integrated optic devices applicable to the recovering of optical signals in interferometric systems for high voltage measurement.