1 |
Virtual sensors for active noise control /Munn, Jacqueline Marie. January 2003 (has links) (PDF)
Thesis (Ph.D.) -- University of Adelaide, School of Mechanical Engineering, 2004. / Bibliography: p.229-238.
|
2 |
Piezoceramic Actuated Transducers for Interior Acoustic Noise ControlGreen, Kimball W. 17 August 2000 (has links)
Weight is a critical parameter in the design of any system launched into space. Current launch costs are on the order of 10,000 dollars per pound of payload capacity. Reducing weight and thus increasing payload capacity is always in the forefront of the design process. One method of increasing the payload capacity of launch vehicles is to reduce the acoustic environment in the interior of the fairing. A major problem is that passive methods currently used for noise suppression do not exhibit significant energy dissipation at low frequencies. This motivates the use of active noise control. Using active noise control for frequencies below 200 to 300 Hz in addition to the passive control means has potential to provide broadband noise suppression and thus a smoother, cheaper ride for any payload. The problem with this technique is that active noise control commonly uses electromagnetic speakers as the control element. The weight of the speaker adds more cost to the application due to the approximate cost per pound to send a launch vehicle and payload to space. At 10,000 dollars per pound of payload capacity, the added cost spent on protecting the payload can potentially reduce the amount of payload capacity a customer receives due to monies spent on non-payload mass. Therefore, necessity dictates a light weight noise control solution.
This work investigates the feasibility of a transducer with less mass than that of a conventional loudspeaker which dissipates energy at the acoustic resonances of an enclosed cavity. The test setup involves using the transducer to lower the sound pressure levels of acoustic resonances which are excited by an external source, thus simulating the launch phase of a launch vehicle. The transducer is used as an actuator to add damping through feedback control.
The transducer is comprised of three thin flexures that are actuated by piezoceramic material attached to both sides. The flexures actuate a speaker cone that is attached to the end of the flexures. The transducer can act as a sensor or an actuator due to the nature of the piezoceramics. The sound absorbing transducer is modeled to couple to the first acoustic resonance of a six foot cylindrical cavity. The cavity acts as a simplified model of a launch vehicle payload fairing. Equations of motion are derived to model actuator motion and the acoustic impedance of the cavity. A state-space model of the system was derived for two cases: a collocated sensor/actuator pair exciting the tube and an external source exciting the tube with the transducer acting as an absorber. The transducer is designed to affect the first mode, however damping is noticed in the next acoustic resonance.
Analysis of the theoretical model indicated up to 70 percent reduction of the open-loop RMS values or a reduction of 10 dB. Experimental results with the optimized transducer produced a 35 percent reduction of the open-loop RMS value or 3.73 dB. The first acoustic resonance coupled well with the first structural mode of the transducer providing optimal noise suppression for the first mode. Damping was also noted in the second acoustic mode. Neglecting the inertia of the tip mass introduced errors in the predictions of the transducer resonances at higher frequencies. This problem limited the ability to control the higher modes of the cavity. / Master of Science
|
3 |
Active control of sound in ductsChan, T. M. January 1997 (has links)
No description available.
|
4 |
Local active control in pure tone diffracted diffuse sound fieldsGarcia Bonito, Juan J. January 1996 (has links)
No description available.
|
5 |
Novel methods of transduction for active control of harmonic sound radiated by vibrating surfacesBurgemeister, Kym A. January 1996 (has links)
Large electric transformers such as those used in high voltage substations radiate an annoying low frequency hum into nearby communities. Attempts have been made to actively control the noise by placing a large number of loudspeakers as control sources around noisy transformers to cancel the hum. These cancellation systems require a large number of loudspeakers to be successful due to the imposing size of the transformer structures. Thus such systems are very expensive if global noise reduction is to be achieved. The aim of this thesis is to investigate theoretically and experimentally the use of thin perforated panels closely placed to a heavy structure to reduce the radiation of unwanted harmonic noise. These panels can themselves be vibrated to form a control source radiating over a large surface surrounding the primary source. The problem of the equipment overheating inside the enclosure is alleviated because the holes in the panels still allow natural cooling. An initial study is carried out to determine the resonance frequencies of perforated panels. The use of previously determined effective elastic properties of the panels and Finite Element Analysis to theoretically calculate their resonance frequencies is examined. Secondly the attenuation provided by active noise control using perforated panels as control sources is explored by use of a coupled analysis, where the primary source is assumed to influence the radiation of the perforated control panel. This analysis was found to predict poorly the amount of attenuation that could be achieved, so an uncoupled analysis is undertaken, where both the primary and control sources are assumed to radiate independently of each other. Not only does this greatly simplify the theoretical analysis but it also enables prediction of attenuation levels which are comparable to those determined experimentally. The theoretical model is reformulated to enable comparison of the sound power attenuation provided by perforated panel control sources with that of traditional acoustic and structural control sources. Finally, the use of modal filtering of traditional acoustic error sensor signals to give transformed mode (or power mode) sensors is examined. The independently radiating acoustic transformed modes of the panel are determined by an eigenanalysis and a theoretical analysis is presented for a farfield acoustic power sensor system to provide a direct measurement of the total radiated acoustic power. The frequency dependence of the sensor system, and the amount of global sound power attenuation that can be achieved is examined. Experimental measurements are made to verify the theoretical model and show that a sound power sensor implemented with acoustic sensors can be used in a practical active noise control system to increase the amount of attenuation that can be achieved. Alternatively the sound power sensor can be used to reduce the number of error channels required by a control system to obtain a given level of attenuation when compared to traditional error criteria. The power mode sensor analysis is then applied to the perforated panel control system, with similar results. / Thesis (Ph.D.)--Engineering (Department of Mechanical Engineering), 1996.
|
6 |
Virtual sensors for active noise control.Munn, Jacqueline M January 2003 (has links)
The need to attenuate noise transmitted into enclosed spaces such as aircraft cabins, automobiles and mining cabins has provided the impetus for many active noise control studies. Studies into active interior noise control began with a pressure squared cost function utilising multiple error sensors and control sources in an attempt to produce global control of the interior sound field. This work found problems with observability of the primary disturbances and a large number of error sensors and control sources were required to produce global control. Since this early work in the 1980's, many new acoustic based cost functions have been developed to improve on the performance of the pressure squared cost function. This thesis will focus on one novel acoustic cost function, virtual error sensing. Virtual error sensing is a relatively new technique which produces localised zones of attenuation at a location remote to the physical sensors. The practical advantage of this method is the people within these enclosed spaces are able to observe a reduction in sound pressure level without their movement being restricted by error sensors located close to their ears. The aim of this thesis is to further investigate the performance of forward-difference virtual error sensors in order to understand the factors that affect the accuracy of the pressure prediction at the virtual location and use this information to develop more accurate and efficient forward- difference virtual sensors. These virtual sensors use linear arrays of microphones containing two or more microphone elements and a linear or quadratic approximation is used to predict the sound at the virtual location. The prediction method determines the weights applied to each microphone signal to predict the sound pressure level at the virtual location. This study investigates susceptibility of the sensors to corruption as a result of phase and sensitivity mismatch between the microphones, as well as in the location of the elements in the error sensing array. A thorough error analysis of the forward-difference virtual microphones was performed in a one-dimensional sound field and in a plane wave sound field. The accuracy of the quadratic virtual microphone was found to be strongly affected by the presence of short wavelength extraneous noise. From this study, two novel virtual error sensing techniques were developed, namely; higher-order virtual sensors and adaptive virtual sensors. The higher-order virtual error sensors still employ the linear and quadratic prediction method but extra microphone elements are added to the array. The aim of these higher-order virtual microphones is to produce a more accurate prediction of the pressure at the virtual location by spatially filtering out any short wavelength extraneous noise that may corrupt the prediction. These virtual sensors were tested in a realtime control scenario in both a one-dimensional reactive sound field and in a free field. This work found that the higher-order virtual microphones can improve the prediction accuracy of the original virtual sensors but are still prone to problems of phase, sensitivity and position errors. Finally, the adaptive LMS virtual sensors were investigated in a SIMULINK simulation and tested experimentally using real-time control in a one-dimensional sound field. It was hoped that an adaptive LMS algorithm could overcome previous difficulties arising from inherent and transducer errors by adapting the weights of the signals from the sensing elements which form the array. The algorithm adapts the sensing microphone signals to produce the same signal as the microphone at the virtual location. Once this has been achieved, the sensing microphone weights are fixed and the microphone at the virtual location is removed, thus creating a virtual microphone. The SIMULINK simulation allowed the performance of the fixed weight and virtual microphones to be investigated in the presence of only phase errors, sensitivity errors and position errors and in the presence of all three combined. This work showed that the adaptive virtual sensors had the ability to compensate for the errors. The number of modes used in the simulations was varied to observe the performance of all virtual sensors in the presence of higher-order modes. The prediction accuracy of the fixed weight virtual sensors was found to be greatly affected by the presence of higher-order modes. The use of the adaptive virtual microphones to produce localised zones of quiet was examined experimentally using real-time control. The study found the real-time control performance is superior to that of the fixed weight higher-order virtual microphones and the original forward-difference virtual microphones. / Thesis (Ph.D.)--School of Mechanical Engineering, 2003.
|
7 |
Frequency Shaped LQR Design of an Active Noise Cancellation HeadphoneLin, Tsai-Fu 26 August 2009 (has links)
The purpose of this thesis is to design and implement an active noise cancellation headphone (ANC) with a feedback controller optimally designed using the linear quadratic regulator (LQR) design approach. The controller compares the audio input signal with the measured signal from a mini microphone in the headphone, and attempts to generate a control signal so that the headphone may reproduce a clean, low noise audio sound, without being interfered by the environmental noise.
The control bandwidth of the ANC headphone is 100~600Hz. The controller design emphasizes the choice of a weighting function in shaping the controller gain at different frequencies, so as to achieve maximum in-band noise cancellation and low noise amplification outside the bandwidth. The experimental result shows achievable noise cancellation of maximum 25dB within the control bandwidth and a barely noticeable slight noise amplification of maximum 6dB at high frequencies and 4.5dB at inaudible low frequencies.
|
8 |
Robust multivariable control of an active acoustic grillage : modeling, design and implementation /Sepp, Kalev, January 2001 (has links)
Thesis (Ph. D.)--University of Washington, 2001. / Vita. Includes bibliographical references (p. 126-129).
|
9 |
Virtual sensors for active noise control.Munn, Jacqueline M January 2003 (has links)
The need to attenuate noise transmitted into enclosed spaces such as aircraft cabins, automobiles and mining cabins has provided the impetus for many active noise control studies. Studies into active interior noise control began with a pressure squared cost function utilising multiple error sensors and control sources in an attempt to produce global control of the interior sound field. This work found problems with observability of the primary disturbances and a large number of error sensors and control sources were required to produce global control. Since this early work in the 1980's, many new acoustic based cost functions have been developed to improve on the performance of the pressure squared cost function. This thesis will focus on one novel acoustic cost function, virtual error sensing. Virtual error sensing is a relatively new technique which produces localised zones of attenuation at a location remote to the physical sensors. The practical advantage of this method is the people within these enclosed spaces are able to observe a reduction in sound pressure level without their movement being restricted by error sensors located close to their ears. The aim of this thesis is to further investigate the performance of forward-difference virtual error sensors in order to understand the factors that affect the accuracy of the pressure prediction at the virtual location and use this information to develop more accurate and efficient forward- difference virtual sensors. These virtual sensors use linear arrays of microphones containing two or more microphone elements and a linear or quadratic approximation is used to predict the sound at the virtual location. The prediction method determines the weights applied to each microphone signal to predict the sound pressure level at the virtual location. This study investigates susceptibility of the sensors to corruption as a result of phase and sensitivity mismatch between the microphones, as well as in the location of the elements in the error sensing array. A thorough error analysis of the forward-difference virtual microphones was performed in a one-dimensional sound field and in a plane wave sound field. The accuracy of the quadratic virtual microphone was found to be strongly affected by the presence of short wavelength extraneous noise. From this study, two novel virtual error sensing techniques were developed, namely; higher-order virtual sensors and adaptive virtual sensors. The higher-order virtual error sensors still employ the linear and quadratic prediction method but extra microphone elements are added to the array. The aim of these higher-order virtual microphones is to produce a more accurate prediction of the pressure at the virtual location by spatially filtering out any short wavelength extraneous noise that may corrupt the prediction. These virtual sensors were tested in a realtime control scenario in both a one-dimensional reactive sound field and in a free field. This work found that the higher-order virtual microphones can improve the prediction accuracy of the original virtual sensors but are still prone to problems of phase, sensitivity and position errors. Finally, the adaptive LMS virtual sensors were investigated in a SIMULINK simulation and tested experimentally using real-time control in a one-dimensional sound field. It was hoped that an adaptive LMS algorithm could overcome previous difficulties arising from inherent and transducer errors by adapting the weights of the signals from the sensing elements which form the array. The algorithm adapts the sensing microphone signals to produce the same signal as the microphone at the virtual location. Once this has been achieved, the sensing microphone weights are fixed and the microphone at the virtual location is removed, thus creating a virtual microphone. The SIMULINK simulation allowed the performance of the fixed weight and virtual microphones to be investigated in the presence of only phase errors, sensitivity errors and position errors and in the presence of all three combined. This work showed that the adaptive virtual sensors had the ability to compensate for the errors. The number of modes used in the simulations was varied to observe the performance of all virtual sensors in the presence of higher-order modes. The prediction accuracy of the fixed weight virtual sensors was found to be greatly affected by the presence of higher-order modes. The use of the adaptive virtual microphones to produce localised zones of quiet was examined experimentally using real-time control. The study found the real-time control performance is superior to that of the fixed weight higher-order virtual microphones and the original forward-difference virtual microphones. / Thesis (Ph.D.)--School of Mechanical Engineering, 2003.
|
10 |
Novel methods of transduction for active control of harmonic sound radiated by vibrating surfacesBurgemeister, Kym A. January 1996 (has links)
Large electric transformers such as those used in high voltage substations radiate an annoying low frequency hum into nearby communities. Attempts have been made to actively control the noise by placing a large number of loudspeakers as control sources around noisy transformers to cancel the hum. These cancellation systems require a large number of loudspeakers to be successful due to the imposing size of the transformer structures. Thus such systems are very expensive if global noise reduction is to be achieved. The aim of this thesis is to investigate theoretically and experimentally the use of thin perforated panels closely placed to a heavy structure to reduce the radiation of unwanted harmonic noise. These panels can themselves be vibrated to form a control source radiating over a large surface surrounding the primary source. The problem of the equipment overheating inside the enclosure is alleviated because the holes in the panels still allow natural cooling. An initial study is carried out to determine the resonance frequencies of perforated panels. The use of previously determined effective elastic properties of the panels and Finite Element Analysis to theoretically calculate their resonance frequencies is examined. Secondly the attenuation provided by active noise control using perforated panels as control sources is explored by use of a coupled analysis, where the primary source is assumed to influence the radiation of the perforated control panel. This analysis was found to predict poorly the amount of attenuation that could be achieved, so an uncoupled analysis is undertaken, where both the primary and control sources are assumed to radiate independently of each other. Not only does this greatly simplify the theoretical analysis but it also enables prediction of attenuation levels which are comparable to those determined experimentally. The theoretical model is reformulated to enable comparison of the sound power attenuation provided by perforated panel control sources with that of traditional acoustic and structural control sources. Finally, the use of modal filtering of traditional acoustic error sensor signals to give transformed mode (or power mode) sensors is examined. The independently radiating acoustic transformed modes of the panel are determined by an eigenanalysis and a theoretical analysis is presented for a farfield acoustic power sensor system to provide a direct measurement of the total radiated acoustic power. The frequency dependence of the sensor system, and the amount of global sound power attenuation that can be achieved is examined. Experimental measurements are made to verify the theoretical model and show that a sound power sensor implemented with acoustic sensors can be used in a practical active noise control system to increase the amount of attenuation that can be achieved. Alternatively the sound power sensor can be used to reduce the number of error channels required by a control system to obtain a given level of attenuation when compared to traditional error criteria. The power mode sensor analysis is then applied to the perforated panel control system, with similar results. / Thesis (Ph.D.)--Engineering (Department of Mechanical Engineering), 1996.
|
Page generated in 0.0731 seconds