This thesis relates to a conceptual design of a light aircraft considering its easy manufacturability in non-professional workshop, for example at home. It is divided into three main parts. At the beginning there is mentioned a summary of existing light airplanes which determines the conceptual frame of the designed aircraft. The next part describes more detailed draft of different functional units, taking into consideration the constructional and manufacturing issues. The final part then contains basic equations to verify and define the most important characteristics of the designed aircraft.

The aim of thesis is to devise the body due to the current model in the 3D software ProEngineer and given by current Formula Student competition rules. Subsequently, the model will be created for the purposes of CFD software for numerical analysis of aerodynamics. Based on this analysis, the simulation will be obtained with the coefficient of air and axles load.

This diploma thesis deals with the calculation of stability and control of the L-13 SE Vivat Powered Glider. Furthermore comparing different methods of determining the aerodynamic derivatives.

This Master’s thesis concerns a theme of wind power in Czech Republic. It gives a brief overview of wind turbines available at the European market, in the observed performance of range 50 kW with subsequent economic analysis for the locality. At the same time, it mentioned a probability distribution and the mathematical models needed for processing and evaluation of meteorological data. Nevertheless, the main part of this work is focused on the aerodynamic design of the blade of wind power plant for given location and it’s both with and without considering the possible losses.

This thesis deals with the aerodynamic analysis and shape modifications of the ARES aircraft. The analysis focuses on the evaluation lift, drag, and pitching moment coefficient, and further to identify the locations of stripping stream which is characterized by high drag. Before the analysis calibration of the CFD solver is done with the model, which has been measured in the wind tunnel. The aim of calibration is to verify the accuracy and veracity of the methodology used in mesh creation and calculated values. Calculated values are compared with measured data. The shape modifications of the aircraft are focused on conceptual design of the suction inlets for cooling radiators and engine aircraft. Aerodynamic analysis is performed with the modified model in order to determine the variation of lift, drag and pitching moment coefficient from its original configuration.

The modern trend of gas turbines design is towards lighter, highly efficient,and more compact engines. Such situation imposes on engineers to continuouslysearch for improved and optimum designs. The thesis presented aims at researching possible performance improvements regarding axial gapdistance in transonic compressors. Decreasing the axial gap would result inlighter engines and achieve design goals. The influence of decreasing the axialgap on performance and structure integrity should be throughly analyzed. This thesis work includes numerical investigations on the axial gap distance effect on performance efficiency and related unsteady aerodynamics phenomena. The first one and a half compressor stages of a Siemens Gas Turbine are modeled in ANSYS CFX. Different axial gap models are simulated for differentconfigurations. The steady state solution is obtained to be initialized for transient time marching calculations. Furthermore, the computational cost of transient calculations is reduced through a geometry scaling technique. The unsteady behavior is further analyzed by a Harmonic Balance solver implemented in STAR-CCM+ software, and compared to a reference case transient calculations. The results obtained supports the presence of an optimalaxial gap distance for maximum efficiency in transonic compressors. Further, the harmonic balance method shows good possibilities for cost and time reductions in transonic compressors performance calculations.

The limitations lying behind the applications of EN-1991-1-4, Eurocode1, actions on structures-general actions-wind load-part 1-4, lead the structural designers to a great confusion. This may be due to the fact that EC1 only provides the guidance for bridges whose fundamental modes of vibration have a constant sign (e.g. simply supported structures) or a simple linear sign (e.g. cantilever structures) and these modes are the governing modes of vibration of the structure. EC1 analyzes only the along-wind response of the structure and does not deal with the cross wind response. The simplified methods that are recommended in this code can be used to analyze structures with simple geometrical configurations. In this report, the analytical methods which are used to describe the fluctuating wind behavior and predict the relative static and dynamic response of the structure are studied and presented. The criteria used to judge the acceptability of the wind load and the corresponding structural responses along with the serviceability considerations are also presented. Then based on the given methods the wind forces acting on a continuous bridge whose main span is larger than the 50 meters (i.e. > 50 meter requires dynamic assessment) is studied and compared with the results which could be obtained from the simplified methods recommended in the EC1.

Modern turbomachinery design is characterized by a tendency towards thinner, lighter and highly loaded blades, which in turn gives rise to increased sensitivity to flow induced vibration such as flutter. Flutter is a self-excited and self-sustained instability phenomenon that may lead to structural failure due to High Cycle Fatigue (HCF) or material overload. In order to be able to predict potential flutter situations, it is necessary to accurately assess the unsteady aerodynamics during flutter and to understand the physics behind its driving mechanisms. Current numerical tools used for predicting unsteady aerodynamics of vibrating turbomachinery components are capable of modeling the flow field at high level of detail, but may fail in predicting the correct unsteady aerodynamics under certain conditions. Continuous validation of numerical models against experimental data therefore plays significant role in improving the prediction accuracy and reliability of the models.   In flutter investigations, it is common to consider aerodynamically symmetric (tuned) setups. Due to manufacturing tolerances, assembly inaccuracies as well as in-service wear, the aerodynamic properties in a blade row may become asymmetric. Such asymmetries can be observed both in terms of steady as well as unsteady aerodynamic properties, and it is of great interest to understand the effects this may have on the aeroelastic stability of the system.   Under certain conditions vibratory modes of realistic blade profiles tend to be coupled i.e. the contents of a given mode of vibration include displacements perpendicular and parallel to the chord as well as torsion of the profile. Current design trends for compressor blades that are resulting in low aspect ratio blades potentially reduce the frequency spacing between certain modes (i.e. 2F &amp; 1T). Combined modes are also likely to occur in case of the vibration of a bladed disk with a comparatively soft disk and rigid blades or due to tying blades together in sectors (e.g. in turbines).   The present investigation focuses on two areas that are of importance for improving the understanding of aeroelastic behavior of oscillating blade rows. Firstly, aeroelastic properties of combined mode shapes in an oscillating Low Pressure Turbine (LPT) cascade were studied and validity of the mode superposition principle was assessed. Secondly, the effects of aerodynamic mistuning on the aeroelastic properties of the cascade were addressed. The aerodynamic mistuning considered here is caused by blade-to-blade stagger angle variations   The work has been carried out as compound experimental and numerical investigation, where numerical results are validated against test data. On the experimental side a test facility comprising an annular sector of seven free-standing LPT blades is used. The aeroelastic response phenomena were studied in the influence coefficient domain where one of the blades is made to oscillate in three-dimensional pure or combined modes, while the unsteady blade surface pressure is acquired on the oscillating blade itself and on the non-oscillating neighbor blades. On the numerical side, a series of numerical simulations were carried out using a commercial CFD code on a full-scale time-marching 3D viscous model. In accordance with the experimental part the simulations are performed using the influence coefficient approach, with only one blade oscillating.   The results of combined modes studies suggest the validity of combining the aeroelastic properties of two modes over the investigated range of operating parameters. Quality parameters, indicating differences in mean absolute and imaginary values of the unsteady response between combined mode data and superposed data, feature values that are well below measurement accuracy of the setup.   The findings of aerodynamic mistuning investigations indicate that the effect of de-staggering a single blade on steady aerodynamics in the cascade seem to be predominantly an effect of the change in passage throat. The changes in steady aerodynamics are thereby observed on the unsteady aerodynamics where distinctive effects on flow velocity lead to changes in the local unsteady pressure coefficients. In order to assess the overall aeroelastic stability of a randomly mistuned blade row, a Reduced Order Model (ROM) model is introduced, allowing for probabilistic analyses. From the analyses, an effect of destabilization due to aero-asymmetries was observed. However the observed effect was of moderate magnitude. / <p>QC 20130610</p> / Turbokraft

Over the last two decades, most developed countries have reached a consensus that greener energy production is necessary for the world, due to the climate changes and limited fossil fuel resources. More efficient turbine is desirable and can be archived by higher turbine-inlet temperature (TIT). However, it is difficult for nozzle guide vane (NGV), which is the first stage after combustion chamber, to withstand a very high temperature. Thus, cooling methods such as film cooling have to be implemented. Film-cooled NGV of an annular sector cascade (ASC) is studied in this thesis, for getting comprehensive calculation of vorticity, and analyzing applicability of existing loss models, namely Hartsel model and Young &amp; Wilcock model. The flow-field calculation methods from previously published studies are reviewed. Literatures focusing on Hartsel model and Young &amp; Wilcock model are studied. Measurement data from previously published studies are analyzed and compared with the loss models. In order to get experience of how measurements take place, participation of a test run experiment is involved. Calculation of flow vector has been evaluated and modified. Actual flow angle is introduced when calculating velocity components. Thus, more exact results are obtained from the new method. Calculation of vorticity has been evaluated and made more comprehensive. Vorticity components as well as magnitude of total streamwise vorticity are calculated and visualized. Vorticity is higher and more extensive for fully cooled case than uncooled case. Highest vorticity is found at regions near the hub, tip and TE. Axial and circumferential vorticities show similar patterns, while the radial vorticity is relatively simpler. Compressibility is introduced as a new method when calculating circumferential and radial vorticities, resulting more extensive and higher vorticities than results from incompressible solutions. Hartsel model and Young &amp; Wilcock model have been evaluated and compared to the ASC to see the applicability of the models. In general, Hartsel model cannot agree with the ASC to a satisfactory level and thus cannot be applied. Coolant velocity is found to be the dominant factor of Hartsel model. Young &amp; Wilcock model may match SS1 and SS2 cases, or even PS and SH4 cases, but cannot match TE case. The applicability of Young &amp; Wilcock model is much dependent on the location of cooling rows.

In this study, the characteristics of the flow around a paraglider wing were investigated through the use of Computational Fluid Dynamics (CFD) simulations by solving both Reynolds Averaged Navier-Stokes equations and Delayed Detached Eddy Simulations were employed. This allowed the observation of how the unique shape of the canopy of a paraglider can influence the behaviour of the flow and how aerodynamic hysteresis can manifest on this sort of wing. Furthermore, the interaction between the highly deformable structure of the paraglider and the flow was examined through a two-way, loosely coupled Fluid-Structure Interaction (FSI) analysis. The methodology for the FSI analysis was first validated by employing a simplified model of the canopy before the full paraglider wing was analysed. Two different structural meshes were tested, using membrane elements or shell elements, respectively. The membrane element mesh prompted a collapse of the structure, while the mesh presenting shell elements allowed for a successful completion of the analysis.