Ce mémoire est consacré au développement de technologies de filtrage novatrices qui apportent un gain en performance permettant de répondre aux besoins de filtrage pour télécommunications spatiales à moyen et long termes. Il s’inscrit dans le projet ANR ATOMIQ coordonné par Thales Alenia Space ayant comme partenaires le laboratoire SPCTS et la société 3D CERAM. Le premier chapitre est constitué d’une étude bibliographique sur les filtres en bande Q et V ainsi que les technologies de fabrication 3D. Le deuxième chapitre est consacré à l’élaboration d’une nouvelle formulation d’alumine très pure à faible pertes et stable en température. Le troisième chapitre présente une conception de filtres hyperfréquences en bande Q et V à base de cavités résonantes diélectriques. Le quatrième chapitre concerne la fabrication des filtres par usinage en cru ainsi que la présentation des différents démonstrateurs fabriqués par stéréolithographie et moulage basse pression. Il présente aussi des solutions de correction post-fabrication par tir laser. Ce travail est original par l’utilisation de la stéréolithographie céramique 3D ainsi que du moulage basse pression pour fabriquer des filtres hyperfréquences de petites tailles en bande Q et V. / This thesis focus on the development of innovative filtering technologies that enhance the performance to meet the filtering requirements for spacial communications. It is part of the ANR project ATOMIQ coordinated by Thales Alenia Space with partners (SPCTS 3D CERAM). The first chapter consists of a literature review on the Q and V band filters as well as 3D manufacturing technologies. The second chapter is devoted to the development of a new formulation of highly pure, low losses and temperature stable alumina. The third chapter presents a microwave filter design in Q and V band based on a dielectric resonant cavity. The fourth chapter is about the manufacturing of filters and presentation of various demonstrators manufactured by stereolithography and low pressure molding. It also provides a post-production correction solutions based on laser shoots. This work is original because, to the best of our knowledge, 3D ceramic stereolithography and the low pressure molding have not been used to produce small sizes Q and V band microwave filters.

The thesis deals with the microstrip filter design using defected ground structure (DGS). The difference between standard asymmetric microstrip technique and DGS is in using the structures etched in the microwave substrate ground plane. The DGS resonant characteristics are then used in filter design. The thesis consists of three factual parts. The first one (chapter 4) introduces the use of the DGS resonators in the lowpass filter design. It involves experimental analysis of one type of the lowpass filter. The second part (chapter 5) deals with a novel microstrip lowpass filter design method using DGS. The proposed method is verified by simulations and several samples are realized and measured. Finally, the third part (chapters 7 and 8) deals with the bandpass filter design using specific defected ground structure as a resonator. The resonators are used in a coupled resonator structure. Filters of various orders and resonator configurations are designed and simulated. A combination of the DGS resonators and half-wavelength microstrip resonators is introduced as well. Selected samples are realized and measurement results are compared with simulations.

By placing millions of space sunshades, of the order of 104 m2 at the sub-Lagrangian point L1',between the sun and Earth, solar radiation can be reduced enough to achieve the necessary temper-ature reduction to enable a slow down of the global warming. The vast amount of space sunshadesposes significant challenges on the communication system, as the probability of interference, whichcan distort information, increases with the number of simultaneously communicating units.This thesis aims to design a potential structure for the communication system that minimizesinterference as much as possible. To reduce the number of simultaneously communicating units, thesunshades are arranged in cell formation, where a mother is placed in the center with daughtersaround that only communicate with their specific cell mother. Direct communication betweenthe Earth and space sunshades is not possible as the interference from solar radiation can causesignificant distortion on the signals. Therefore, relay satellites are placed in orbit around thesub-Lagrangian point L1' at a sufficient distance to avoid the effects of solar radiation. Thus, thecommunication between the mothers and Earth is instead routed via the relay satellites. Sincecommunication between such a large number of entities in space has not been investigated before,this approach could provide a possible basic design framework for designing such infrastructure inthe future.

Ultraprecision single point diamond turning is required to produce parts with sub-nanometer surface roughness and sub-micrometer surface profiles tolerances. These parts have applications in the optics industry, where tight form accuracy is required while achieving high surface finish quality. Generally, parts can be polished to achieve the desired finish, but then the form accuracy can easily be lost in the process rendering the part unusable. Currently, most mid to low spatial frequency surface finish errors are inspected offline. This is done by physically removing the workpiece from the machining fixture and mounting the part in a laser interferometer. This action introduces errors in itself through minute differences in the support conditions of the over constrained part on a machine as compared to the mounting conditions used for part measurement. Once removed, the fixture induced stresses and the part’s internal residual stresses relax and change the shape of the generally thin parts machined in these applications. Thereby, the offline inspection provides an erroneous description of the performance of the machine. This research explores the use of a single, high resolution, capacitance sensor to quickly and qualitatively measure the low to mid spatial frequencies on the workpiece surface, while it is mounted in a fixture on a standard ultraprecision single point diamond turning machine after a standard facing operation. Following initial testing, a strong qualitative correlation exists between the surface profiling on a standard offline system and this online measuring system. Despite environmental effects and the effects of the machine on the measurement system, the capacitive system with some modifications and awareness of its measurement method is a viable option for measuring mid to low spatial frequencies on a workpiece surface mounted on an ultraprecision machine with a resolution of 1nm with an error band of ±5nm with a 20kHz bandwidth. / Thesis / Master of Applied Science (MASc)