1 |
Development of a detect-and-avoid sensor solution for the integration of a group 3 large unmanned aircraft system into the national airspace systemRyker, Kyle Bradley 06 August 2021 (has links)
Unmanned Aircraft Systems (UAS) face one common challenge when integrating with the existing manned aircraft population in the National Airspace System (NAS). To unlock the full efficiency of UAS, the UAS integrator must comply with an onboard pilot’s requirement to see-and-avoid other aircraft while operating. Commercially available Detect-and-Avoid (DAA) sensor technologies have been developed to attempt to comply with this requirement. UAS integrators must use these sensors to meet or exceed the performance of a human pilot. This thesis covers research done to integrate an array of commercially made DAA sensors with a large Group 3 UAS both in hardware and software that was later flight tested and evaluated for usability. A fast-time simulation is presented using the principles of the National Aeronautics and Space Administration's (NASA) Detect-and-AvoID Alerting Logic for Unmanned Systems (DAIDALUS). Last, open-source tools are presented to assist future integrators in validating their DAA solutions.
|
2 |
An Unmanned Aerial Systems Evaluation Chamber for Bridge InspectionJose Capa Salinas (11178285) 26 July 2021 (has links)
<p>Civil engineering structures must provide an adequate and safe performance during their time of service, and the owners of these structures must have a reliable inspection strategy to ensure time-dependent damage does not become excessive. Visual inspection is the first step in every structural inspection; however, many elements in the majority of structures are difficult to access and require specialized personal and equipment. In an attempt to reduce the risk of the inspector and the cost of additional equipment, the use of Unmanned Aircraft Systems (UAS) has been increasing in the last years. The absence of standards and regulations regarding the use of UAS in inspection of structures has allowed the market to widely advertise Unmanned Aerial Vehicles (UAV) without protocols or qualifications that prove their effectiveness, leaving the owners of the structures to solely rely on claims of the vendors before deciding which technology suits their particular inspection needs. Focusing primarily on bridge inspection, this research aimed to address the lack of performance-based evaluation and standards for UAS, developing a validation criterion to evaluate a given UAS based on a repeatable test that resembles typical conditions in a structure. </p><p><br></p><p>Current applications of UAS in inspection of structures along with its advantages and limitations were studied to determine the current status of UAS technologies. A maximum typical rotor-tip-to-rotor-tip distance of an UAV was determined based on typical UAVs used in bridge inspection, and two main parameters were found to be relevant when flying close to structures: proximity effects in the UAV and availability of visual line of sight. Distances where proximity effects are relevant were determined based on several field inspections and flights close to structures. In addition, the use of supplementary technologies such as Global Positioning System (GPS) and Inertial Measurement Units (IMU) was studied to understand their effect during inspection. </p><p><br></p><p>Following the analysis, the author introduces the idea of a series of obstacles and elements inside an enclosed space that resemble components of bridge structures to be inspected using UAVs, allowing repeatability of the test by controlling outside parameters such as lighting condition, wind, precipitation, temperature, and GPS signal. Using distances based on proximity effects, maximum typical rotor-tip-to-rotor-tip distance, and a gallery of bridges and situations when flying close to bridge structures, a final arrangement of elements is presented as the evaluation chamber. Components inside the evaluation chamber include both “real” steel and concrete specimens as well as those intended to simulate various geometric configurations on which other features are mounted. Pictures of damages of steel and concrete elements have been placed in the internal faces of the obstacles that can be assessed either in real-time flight or in post-processing work. A detailed comparison between the objectives of this research project and the results obtained by the evaluation chamber was performed using visual evaluation and resolution charts for the images obtained, the availability of visual line of sight during the test, and the absence of GPS signal.</p><p><br></p><p>From the comparison and analysis conducted and based on satisfactory flight results as images obtained during flights, the evaluation chamber is concluded to be a repeatable and reliable tool to apply to any UAS prior to inspect bridges and other structures, and the author recommends to refrain from conducting an inspection if the UAS does not comply with the minimum requirements presented in this research work. Additionally, this research provided a clearer understanding of the general phenomenon presented when UAVs approach structures and attempts to fill the gap of knowledge regarding minimum requirements and criterion for the use of UAS technologies in inspection of structures.</p>
|
Page generated in 2.7602 seconds