Carbon Capture and Storage (CCS) is a legitimate technology option that should be part of a balanced portfolio of mitigation technologies available Post-Kyoto Protocol framework after Paris 2015 and beyond the 2020s or the cost achieving 2 degrees Celsius stabilisation scenario will significantly increase. Oxy-fuel combustion as a CCS technology option increases fuel flexibility. Additionally, oxy-biomass as a bio-energy with CCS (BECCS) technology can achieve negative carbon dioxide (CO2) emissions in sustainable biomass systems. Also, oxygen (O2) production in an air separation unit (ASU) gives potential for extra operational flexibility and energy storage. In this work, new designs of 20 litre spherical (R-20) and 30 litre non-spherical (R-30) ignition chambers have been built at the University of Edinburgh to carry-out dust ignition experiments with different ignition energies for evaluating pulverised fuel ignitability as a function of primary recycle (PR) O2 content for oxy-fuel PF milling safety. A set of coals and biomasses being used (at the time of submitting this work) in the utility pulverised fuel boilers in the UK have been employed. Coal and biomass dusts were ignited in air and oxy-fuel mixtures up to 30 % v/v O2 balance mixture CO2 where peak pressures (Pmax) from ignition were recorded. Pressure ratios (Pmax/Pinitial) were determined the key parameter for positive ignition identification with a value above 2.5 to be considered positive. Particle size effects in coal and biomass ignition were evaluated. Results on biomass were more variable than with coals, requiring a stronger ignition source (5,000 J) mainly due to larger particle sizes. Finer biomass particles behaved similarly to air ignition in 25 % v/v O2 in CO2. Larger particles of biomass did not ignite at all for most cases even reaching 30 % v/v O2 in CO2. A reference coal used, El Cerrejon, behaved as expected with 30 % v/v O2 balance CO2 matching air case; particles between 75-53 microns had lower ignitability than finer below 53 microns but were critical in devolatilisation. Most fuels did not ignite in 21 % v/v in CO2 below 200 g/m3 concentrations. The use of adequate ignition energy strength is needed for the PF mill safety case, with 5,000 J energy required for the biomasses tested. An indication of potential ignition chamber volume and geometry effect has also been observed when comparing results from R-20 and R-30 ignition chambers. Important implications include that oxy-biomass PR with 21 % v/v O2 content would give improved pulverised fuel (PF) milling safety when compared to air firing but reduced ignitability and a 25 % v/v O2 balance CO2 atmosphere would approach to oxy-biomass ignition behaviour in air in mills.

Doctor of Philosophy / Department of Grain Science and Industry / Dirk E. Maier / Increased mandates for the production of transportation fuels from renewable resources have thrust the conversion of lignocellulosic biomass, e.g., energy crops and agricultural residues, to ethanol into commercial production. The conversion of biomass to ethanol has been implemented; transportation and storage logistics are still obstacles to overcome by industry. Limited harvest windows throughout the year necessitate extended periods of biomass storage to maintain a consistent, year-round supply to the biorefinery. Sorghum biomass stored with no coverage (NN), covered with tarp (NT), wrapped in plastic (PN) and covered with a tarp and wrapped in plastic (PT) for six months was analyzed for changes in biomass components—cellulose, hemicellulose and lignin, cellulose and hemicellulose degrading enzymes, and conversion to ethanol yields. Treatment NN had increased enzyme activity, and reduced cellulose content and ethanol yields; while biomass covered maintained enzyme activity, cellulose content and ethanol yields. Sequencing of the Large SubUnit (LSU) region and the internal transcribed spacer (ITS) regions of ribosomal RNA gene gave consistent results of fungal community dynamics in biomass stored as previously described. Fungal community richness and diversity increased, while evenness decreased in uncovered biomass during storage. Covered and uncovered storage treatments and over time were found to exhibit distinctly different fungal communities. In contrast, bacterial communities were found to be unresponsive to storage treatments and durations. Cladosporium, Alternaria and Cryptococcus were found to be the most abundant in the stored biomass. Covering of biomass strongly limits the arrival and establishment of new fungal propagules in stored biomass, reducing biomass degradation by these often pathogenic, saprobic or endophytic communities. Overall, covering of biomass during storage is essential for optimal substrate retention for downstream processing into ethanol. In addition, storage and transportation logistics of three real-world scenarios were evaluated for the conversion of wheat straw, corn stover and sorghum stalks residues to ethanol at a biorefinery located in Southwest Kansas. Economic evaluation revealed that transport and storage of residues at satellite storage facilities was most economical for farmers and would create opportunity for the operation of profitable facilities that would supply the local biorefinery on demand throughout the year.

I carried out several large, manipulative greenhouse and controlled-setting experiments to elucidate Panicum hemitomon growth response as influenced by environmental conditions associated with restoring thick-mat floating marsh. Initially, Panicum hemitomon growth response was assessed in conjunction with manipulated nutrient availability and hydrology. Next, I assessed Panicum hemitomon growth response in conjunction with a suite of substrate and mat or containment materials. Finally, I evaluated Panicum hemitomon growth response, as well as overall created floating marsh vegetated development, using both a multi-species planting approach and a suite of Panicum hemitomon establishment techniques. All partitions of Panicum hemitomon biomass (shoot, rhizome, and root material) were enhanced under nitrogen, and to a lesser extent, phosphorous enrichment. Saturated (not inundated) hydrologic conditions were most conducive for robust growth by all partitions of Panicum hemitomon biomass. Substrate and mat or containment materials had a significant effect on Panicum hemitomon vigor, with peat and peat-containing blended substrate materials being most conducive for vigorous Panicum hemitomon growth. Duralast coconut fiber was the most suitable mat or containment material based not only on measures of plant vigor, but also for reasons associated with strength and stability, as well as buoyancy. The combination of Panicum hemitomon and Ludwigia peploides was superior to any other multi-species treatment tested. Ludwigia peploides was highly resilient to transplanting, grew vigorously in a lateral fashion, produced significantly more biomass than any other secondary species, and enhanced overall mat buoyancy, all key metrics regarding successful floating marsh restoration. Equally as important, the large amount of biomass attained by Ludwigia peploides was not totally at the expense of vigorous Panicum hemitomon growth. With respect to establishment technique, the positive response of Panicum hemitomon rhizome growth to humic acid amendment warrants further study. This research generated data that not only advance the body of general ecological knowledge pertaining to Panicum hemitomon, the dominant macrophyte of thick-mat floating marsh, but equally as important, data that are likely to augment or enhance the creation and restoration of this important freshwater marsh type.

Orientador: Dilermando Perecin / Coorientador: Marcos Guimarães de Andrade Landell / Coorientador: Mauro Alexandre Xavier / Banca: Ivana Marino Barbaro / Banca: Ricardo Augusto Dias Kanthack / Banca: Miguel Angelo Mutton / Banca: Luciana Rossini Pinto / Resumo: Há alguns anos se tem falado e mostrado a necessidade de geração de energia através de fontes renováveis, pouco poluentes e que possam ajudar a atender a alta demanda de combustíveis que vem sendo gerada de forma cada vez mais acelerada. Com o intuito de auxiliar nessa questão, procurou-se identificar genótipos superiores em produção de biomassa para produção de bionergia, oriundos de três cruzamentos entre cultivares comerciais de cana-de-açúcar e genótipos de Saccharum spontaneum. Foram utilizados três cruzamentos, sendo um biparental denominado de Família 5002 (RB855465 x GLAGAH) e dois policruzamentos denominados de Família 5006 (NG26011 x ?) e Família 5008 (SE5069 x ?). Os seedlins cedidos ao IAC (Instituto Agronômico de Campinas) foram transplantados no dia 05 de abril de 2011 no Centro de Cana em Ribeirão Preto/SP. O delineamento utilizado foi o de blocos aumentados, com 9 blocos de 3 parcelas, cada parcela com 5 linhas de 10 plantas cada, totalizando 1.350 plantas. O espaçamento utilizado foi de 1,5 x 1,5 m (entre plantas e entre linhas). Como cultivares padrão, foram utilizadas 5 cultivares comerciais (IACSP95-5000, IACSP95-5094, IAC91-1099, IACSP93-3046 e IACSP94-2101). A colheita de cana planta foi realizada aos 10 meses após o plantio e a de cana soca 7 meses após o primeiro corte. Foram avaliadas características biométricas, de produção e análises tecnológicas, além da seleção fenotípica massal dos indivíduos com melhor perfil bioenergético e correlação entre os atributos. Na comparação entre as médias das famílias e dos cruzamentos padrão, houve diferença significativa, com exceção da Família 5008 que não diferiu das cultivares. Das 326 progênies selecionadas durante a seleção massal, 245 foram da Família 5002, 19 foram da Família 5008 e 62 foram da Família 5006. Na seleção pela análise estatística, via modelos mistos, a produtividade genotípica predita das... / Abstract: For a few years now, it has been discussed and exposed the need of energy generation through renewable, low-polluting sources that might be able to attend to the high demand for fuel, which is constantly growing. With the purpose of aiding in this matter, it was intended to identify genotypes with superior biomass production for energy production, descending from three crossbreeds between sugarcane commercial cultivars and genotypes from Saccharum spontaneum. Three crossbreeds were used, being one biparental crossbreed named Family 5002 (RB855465 x GLAGAH) and two polycrosses named Family 5006 (NG26011 x ?) and Family 5008 (SE5069 x ?). The seedlings provided to the IAC (Instituto Agronômico de Campinas - Agronomic Institute of Campinas) were transplanted in April 5th 2011 from the Sugar Cane Center in Ribeirao Preto/SP. It was used the augmented block design, with 9 blocks of 3 portions each, each portion having 5 lines of 10 plants each, totalizing 1350 plants. The spacing used was 1.5 x 1.5 m (between plants and lines). As standard cultivars, were used 5 commercial cultivars (IACSP95-5000, IACSP95-5094, IAC91-1099, IACSP93-3046 and IACSP94-2101). The harvest of each plant was performed 10 months after plantation and the ratoon cane 7 months after the first cut. Were evaluated characteristics regarding biometry, production and technological analyzes, and also mass phenotypic selection of subjects with better bioenergetics profile and correlation between the attributes. In the comparison between the medium of families and standard crossbreeds, a significant difference was noted, except the Family 5008 which wasn't different from the cultivars. From the 326 progenies chosen during the mass selection, 245 were from Family 5002, 19 from Family 5008 and 62 from the Family 5006. The selection by statistic analysis, via mixed models, the predicted genotypic productivity of the 30 superior progenies varied from 176.70 to 221.31 ... / Doutor

In the wake of ever more occurring and evident consequences brought by climate change such as droughts and an increasing world population, a responsible use and handling of freshwater has never been as important as before. Stormwater is more than often not treated and simply released back in nature with any kind of pollution it has collected on its way, one of which being heavy metals. By treating stormwater not only would this underutilised resource be made use of, creating a new source of freshwater, but environmental pollution caused by untreated stormwater could be potentially decreased, as it can be converted into a potential resource rather than a waste caused by nature. There are a number of already established methods to lower the concentration of heavy metals in water, however there are inherent economical and practical disadvantages with each of them. A method that has shown promising results with potential to challenge these contemporary solutions is biosorption. This study has explored the use of fungal biomass of Rhizopus oryzae for heavy metal biosorption in conjuncture with an organic filler material. The metals investigated were Zn, Cu and Fe. Moreover, the effects of pre-treating the fungal biomass with primarily NaOH were also investigated together with the optimal ratio between biomass and filler material and retention time, in order to maximise biosorption.Pre-treating the fungal biomass with NaOH resulted in a considerable increase in biosorption. Moreover, the presence of the filler material had a positive impact on biosorption by further enhancing it. The best effect was obtained at a 4:1 ratio between biomass and filler material. Finally, the best retention time was determined to be around 2 hours, slowly levelling off at higher retention times. However, the use of pre-treated R. oryzae with filler material did not prove to be efficient regarding the removal of heavy metal ions in stormwater at very low concentration of metals, between approximately 4 to 10 ppb. In the future, it would be worthwhile to investigate the viability of this method on stormwater with higher metal concentrations as well as looking into the effects of pH and temperature. / Som en påföljd av de konsekvenser som klimatförändringen har orsakat, som till exempel svåra torkor tillsammans med en ökande världsbefolkning, har det blivit av allt större vikt att hanteringen av sötvatten sker på ett mer ansvarsfullt och hållbart sätt. Stormvatten brukar inte behandlas överhuvudtaget utan släpps tillbaka i miljön tillsammans med föroreningarna som det samlat på sig under sin väg, bland annat tungmetaller.Det finns redan ett antal metoder för att minska koncentrationen av tungmetaller i vatten, dock inte utan ekonomiska och praktiska svårigheter. Hur som helst så har det forskats en del kring en relativt ny metod som har tidigare visat goda resultat och skulle kunna konkurrera med befintliga lösningar, nämligen biosorption. I denna studie har man utforskat möjligheten att använda svampen Rhizopus oryzae tillsammans med ett organiskt fyllmedelsmaterial för biosorptionen av tungmetaller i stormvatten. De tungmetaller som undersöktes var Zn, Cu och Fe. Dessutom har man undersökt effekterna av ett förbehandlingssteg hos biomassan med NaOH tillsammans med det optimala förhållandet mellan biomassan och fyllemedelsmaterialet och retentionstiden för att maximera biosorptionen. Förbehandlingssteget visade en markant förbättring av biosorptionen. Fyllemedelsmaterialet hade för övrigt också en positiv inverkan genom att ytterligare öka biosorptionen. Ett 4:1 förhållande mellan biomassan och fyllemedelsmaterialet resulterade i det optimala förhållandet för komponenterna med tanke på biosorptionen. För retentionstiden visade det sig de bästa resultaten erhålles vid 2 timmar i lösningen. Emellertid visade det sig att användningen av den förbehandlade svampen tillsammans med fyllemedelsmaterialet inte var effektivt på stormvatten med en väldig låg tungmetallkoncentration, ungefär mellan 4 till 10 ppb. I framtiden skulle det vara intressant att undersöka inte bara metodens genomförbarhet på stormvatten med högre metallkoncentrationer, utan även hur pH-värde samt temperatur kan påverka resultaten.

Student Number : 0310612G - MSc research report - School of Geography, Archaeology and Environmental Studies - Faculty of Science / Wildfire prediction and management is an issue of safety and security for many rural communities in South Africa. Wildfire prediction and early warning systems can assist in saving lives, infrastructure and valuable resources in these communities. Timely and accurate data are required for accurate wildfire prediction on both weather conditions and the availability of fuels (vegetation) for wildfires. Wildfires take place in large remote areas in which land use practices and alterations to land cover cannot easily be modelled. Remote sensing offers the opportunity to monitor the extent and changes of land use practices and land cover in these areas. In order for effective fire prediction and management, data on the quantity and state of fuels is required. Traditional methods for detecting vegetation rely on the chlorophyll content and moisture of vegetation for vegetation mapping techniques. Fuels that burn in wildfires are however predominantly dry, and by implication are low in chlorophyll and moisture contents. As a result, these fuels cannot be detected using traditional indices. Other model based methods for determining above ground vegetation biomass using satellite data have been devised. These however require ancillary data, which are unavailable in many rural areas in South Africa. A method is therefore required for the detection and quantification of dry fuels that pose a fire risk. ASTER and MAS (MODIS Airborne Simulator) imagery were obtained for a study area within the Lowveld region of the Limpopo Province, South Africa. Two of the ASTER and two of the MAS images were dated towards the end of the dry season (winter) when the quantity of fuel (dry vegetation) is at its highest. The remaining ASTER image was obtained during the middle of the wet season (summer), against which the results could be tested. In situ measurements of above ground biomass were obtained from a large number of collection points within the image footprints. Normalised Difference Vegetation Index and Transformed Vegetation Index vegetation indices were calculated and tested against the above ground biomass for the dry and wet season images. Spectral response signatures of dry vegetation were evaluated to select wavelengths, which may be effective at detecting dry vegetation as opposed to green vegetation. Ratios were calculated using the respective bandwidths of the ASTER and MAS sensors and tested against above ground biomass to detect dry vegetation. The findings of this study are that it is not feasible, using ASTER and MAS remote sensing data, to estimate brown and green vegetation biomass for wildfire prediction purposes using the datasets and research methodology applied in this study. Correlations between traditional vegetation indices and above ground biomass were weak. Visual trends were noted, however no conclusive evidence could be established from this relationship. The dry vegetation ratios indicated a weak correlation between the values. The removal of background noise, in particular soil reflectance, may result in more effective detection of dry vegetation. Time series analysis of the green vegetation indices might prove a more effective predictor of biomass fuel loads. The issues preventing the frequent and quick transmission of the large data sets required are being solved with the improvements in internet connectivity to many remote areas and will probably be a more viable path to solving this problem in the near future.

A dissertation submitted to the Faculty of Engineering and the Built Environment, University of the Witwatersrand, Johannesburg, in fulfilment of the requirements for the degree of Master of Science in Engineering. October 2017 / Increasing concerns over environmental and geo-political issues on resources’ sustainability have driven the industries to shift their efforts to produce chemicals from renewable biomass. Amongst the lignocellulosic biomass, corncob contains cellulose, hemicellulose and lignin that are built in a compact structure which makes it difficult to access. Pre-treatment is then applied to make the content to be accessible to enzymatic hydrolysis which breaks down the polysaccharides to monomers. The sugar monomers can be converted to a wide range of bioproducts such as biofuels and bio-chemicals. The objective of the study was to determine, evaluate and optimize the best solvent system to pre-treat corn cob. In addition, the study evaluated the effect of pre-treatment parameters on the yield of cellulose and hemicellulose and attempt to develop a kinetic model to explain the dissolution. Lithium perchlorate, zinc chloride, phosphoric acid, sulphuric acid and sodium hydroxide were used during the pre-treatment, which was carried out at 70-80 ° C for 6 hours. Characterization of pre-treated samples showed a significant change in structure after pretreatment indicating disruption in cell wall of the lignocellulosic material. FTIR revealed a reduction in phenolic group; indicating that the lignin content has been reduced. The XRD patterns show that crystallinity was considerably reduced; this was shown by an increase in calculated crystallinity index (CrI) after LiClO4, ZnCl2, H3PO4 and NaOH pre-treatment. The CrI of raw corncob (CrI= 32.7%) increased to 46.2 %, 42.3 %, 55.6 % and 53.4 % of LiClO4, ZnCl2, H3PO4 and NaOH, respectively. The crystallinity index increased for pre-treated material, indicating that the amorphous cellulose is dissolved in the liquor, as well as lignin and hemicellulose removal This study has shown that LiClO4.2H2O pretreatment agent is an efficient solvent system to pretreat corncob which consecutively increase the accessibility of cellulose and hemicellulose from the solid fractions. The accessibility was confirmed by an ease hydrolysis of cellulose & hemicellulose to glucose & xylose respectively. An increase of nearly four times compared to the untreated corncob. The effect of reaction operating parameters i.e. Reaction time, temperature and solvent concentration was carried out and then optimized by response surface methodology (RSM) using Minitab 16. The target was to maximize the yield of cellulose and hemicellulose. It was discovered that the increase in temperature and reaction time increase the accessibility of cellulose and hemicellulose until an equilibrium is reached at 3 & half hours and 176 °c. The pretreatment solvent concentration was discovered to have an effect on the accessibility but not as much as temperature and time. The best pretreatment conditions to obtain high polysaccharides conversions to monomers were at 176°c for 3.5 hours using LiClO4.2H2O for 10 g of corncob. The results obtained from RSM were used to evaluate the temperatures profile, kinetic model for the corncob pretreatment as a function of temperature. The kinetics of pretreatment were studied by the amount of glucose, xylose and the lignin removed from the pretreated solids. The kinetic model of lignin removal and sugars accessibility was identified as a first-order reaction corresponding to the bulk phase for pretreatment time up to 24 hours. The rate constant results show that the kinetic rate increased with temperature. The activation energy for glucose, xylose and lignin were calculated to be 15.0 kJ/mol, 14.2 kJ/mol and 36.54 kJ/mol, respectively. / MT 2018

Submitted to School of Chemical and Metallurgical Engineering, Faculty of Engineering and the Built Environment, University of the Witwatersrand, Johannesburg, South Africa June, 2016 / The main objective of this study is to produce biofuel from waste animal fat (collected from abattoirs) using the pyrolysis (thermal cracking) method. To achieve this goal, the study investigated the effects of temperature and heating rate on the yield and quality of the bio-oil produced. Also investigated was the effect of zeolite nano-catalyst(s) on the quality of the bio-oil produced. Animal waste fat (tallow) was pyrolyzed in a laboratory fixed bed reactor of volume 2200 cm3 at final temperatures (FT), 450oC, 500oC, 530oC and 580oC using heating rates (HR) of 4oC/min, 5oC/min and 6oC/min. The properties of the resultant bio-oils were tested and analyzed. The maximum bio-oil yield of 82.78 % was achieved at 530oC FT and 6oC /min HR while the highest calorific value, 52.41 MJ/kg, was recorded from the bio-oil produced at the FT of 580oC and 6oC/min HR. The molecular components of each of the bio-oil samples was analyzed using the Gas Chromatography – Molecular Spectrograph (GC-MS) which indicated the predominant presence of alkanes, alkenes, carboxylic acids and alkyl esters in the bio-oils produced without a catalyst. The introduction of zeolites in nano-form yielded relatively more cyclo-alkanes and aromatics. A maximum yield of 58% was recorded when 1% of the zeolite nano-catalyst was used to pyrolyse the tallow at 530oC FT and 6oC/min HR but with lots of coking and gas formation. The viscosity improved with a 35% reduction for the samples produced with 1% zeolites (C1 and C2). The viscosity of the bio-oil produced with 2% zeolites improved with a resultant 34% reduction in value. For pyrolysis done at 530oC FT and 6oC/min HR, the bio-oils with 1% (C1) and 2% zeolite (C3) resulted in a reduction in acid value of 32% and 30%, respectively. Acid value is the mass of potassium hydroxide (KOH) in milligrams that is required to neutralize one gram of chemical substance. / MT2016

A thesis submitted to the Faculty of Engineering and the Built Environment, University of the Witwatersrand, Johannesburg, in fulfilment of the requirements for the degree of Doctor of Philosophy. Johannesburg 10th of October 2016 / Thermal pyrolysis is one of the viable technologies suitable for the management of organic solid waste, which has become a global challenge over the years. This is due to the non-biodegradability of these materials and their continuous usage across all segments of man’s daily activities. Effectiveness of the method is in converting these materials under controlled process conditions, that enable the optimization of the fraction of interest, such as the liquid fraction also referred to as pyrolytic oil with a near zero pollution effect on the environment. The main setback in the production of the liquid fraction include low yield, presence of sulphur and other aromatic compounds which have been linked to environmental pollution and health complications. This study focuses on improving the liquid fraction yield and composition obtainable from pyrolysis process. Latex natural rubber (obtained from Hevea Brasiliensis) was pyrolysed and its products compared with that of the used tyres. The production of pyrolytic oil from used tyres and natural rubber was performed using thermal and catalytic pyrolysis processes. The operating temperature range of 375 to 750 oC (at an interval of 75 oC) at a heating rate of 15oC/min and feed material particle sizes of 2, 4, 6, 8 and 10 mm were used. In addition, Zeolite NaY was synthesized from Lawani Benin River Kaolin (LBK) at a synthesis time and temperature of 9 h and 100 oC respectively, using hydrothermal synthesis method, and used for catalytic pyrolysis. The chemical characterisation revealed pyrolytic oil composition to be a complex mixture of aliphatic, aromatics, polycyclic aromatic hydrocarbons and other oxygen, nitrogen, sulphur and chlorinated compounds in small proportions. The non-catalysed and catalysed pyrolysis using natural rubber resulted in pyrolytic oil with 80 and 66% of aliphatic, 12 and 15% aromatic (with polycyclic aromatic hydrocarbons concentration of 2 and 1%). The non-catalysed and catalysed pyrolysis using used tyres yielded pyrolytic oil with 42 and 32% of aliphatic, 34 and 39% aromatic (with polycyclic aromatic hydrocarbons concentrations of 18 and 23%). The kinetics of the thermal degradation with the aid of a thermogravimetry and differential thermogravimetry analyzer was performed over a temperature range of 30 to 800 oC at a heating rate of 15, 20 and 30oC/min. Results showed that natural rubber displayed higher activation energy than used tyres, with respect to the heating rates. This is an indication that natural rubber is more difficult to thermally decompose than used tyres. The distillation temperature of the distillates was within the temperature range of the conventional petrol and diesel. The composition of the distillates revealed carbon chain length of C5-C30 with majority being C8 – C10. A spark ignition generator engine was used to perform the combustion tests for the various pyrolytic oil distillates and petrol blended in the ratio 0, 5, 10, 15 and 20% successfully without engine modification. For the fuel consumption with respect to generator run time, it was observed that an optimum of 20% natural rubber pyrolytic oil distillates (NRPD)-Petrol blend gave comparative fuel consumption behavior with that of commercial petrol. Furthermore, the 20% NRPD distillates gave optimum fuel consumption and power. Hence, a significant yield improvement and combustion performance were observed for the pyrolytic oil derived from natural rubber than that of used tyres. Further treatment of the pyrolytic oil distillates could pave the way for effective use of the oil as chemical feedstock for industries, or as substitutes for fossil fuel. It was also requisite to develop a mathematical model which adopts thermogravimetry analyser (TGA) as a dynamic apparatus to predict weight change of a material as it degrades with time at a fixed temperature. The proposed models were in three consecutive phases which were classified into three time zones 0 ≤ t ≤ t1, t1 ≤ t ≤ t2 and t ≤ t2. The general model equation for the first phase of degradation was 2 0 1 2 0 ( ) t T w t w e   , while the second phase model was and at the third phase, it is assumed that the limit of weight loss (in the second phase equation) as t tends to ∞ gives a value k , at which change in weight loss with time is negligible. The proposed model was used to plot graph of weight loss versus time at different fixed temperature which fitted well with the experimental TGA and had a characteristic pattern fitted closely to the second phase degradation of the fixed bed reactor. / MT2017

La croissance démographique mondiale, associée à une augmentation générale du niveau de vie, se traduit par l'explosion des besoins en matières premières et énergie. Afin de relever ce défi, une attention accrue est accordée aux énergies et ressources naturelles renouvelables. Parmi elles, la biomasse est particulièrement prometteuse. Elle présente des avantages certains (abondance, répartition homogène) mais aussi plusieurs inconvénients (faible densité énergétique, humidité élevée,…). Pour surmonter ces difficultés, la torréfaction est la méthode la plus connue, mais elle induit une augmentation des taux de cendres et une perte de matière. La carbonisation hydrothermale (HTC) est une alternative possible. L'objet de cette thèse est l'étude de la HTC comme moyen de bonifier la biomasse lignocellulosique. Trois axes principaux ont été considérés: augmentation de la densité énergétique, récupération de molécules, et minéraux d'intérêt. L'étude porte d'abord sur la HTC de systèmes moléculaires représentatifs de ceux présents dans le bois. Le hêtre a été étudié comme biomasse modèle, permettant de déterminer des conditions expérimentales optimales, appliquées ensuite à diverses biomasses. Enfin d'autres méthodes d'activation ont été testées telles que les micro-ondes et les fluides supercritiques. Les hydrochars obtenus après HTC présentent une diminution concomitante des ratios atomiques H/C et O/C. La phase liquide contient différentes molécules d'intérêt (furfural,…). Enfin, les teneurs en cendres diminuent après HTC du fait d'une lixiviation partielle de certains éléments (alcalins et alcalino-terreux). En conclusion, la HTC semble être une alternative intéressante à la torréfaction ; elle permet la production d'hydrochars avec des teneurs élémentaires adaptées à une utilisation en gazéification et la récupération de molécules et minéraux. L'intérêt et la faisabilité technique ont été démontrés en particulier sur des biomasses humides (plantes agricoles) ou polluées (broyats de déchetterie). / Population growth, coupled with a general increase in standard of living, result in a booming demand for raw material and energy. To face this challenge, an increased attention is paid to the use of renewable energies and natural resources. Among them, biomass is especially promising. Its advantages (abundance, distribution all over the Earth) are balanced by several drawbacks (low energy density, high moisture content,…). To overcome these problems, torrefaction is the most traditional way, but it has some inconveniences (increased ash content, loss of material). Hydrothermal carbonisation (HTC) is a possible alternative. The purpose of this thesis is the study of HTC a means to beneficiate the lignocellulosic biomass. Three main aims were identified: increase of the energy density, recover molecules and minerals of interest. The study initially focused on HTC of molecular model systems present in wood. Beech wood was also studied, as a model biomass. This study allowed determining optimal experimental conditions for treatment of further biomasses. Finally, other activation methods have been tested, such as microwaves, and supercritical fluids. Hydrochars obtained after HTC feature a concomitant decrease of the atomic H/C and O/C ratios. Liquid phase contains different molecules of interest (furfural,…). Finally, ash content decreases after HTC owing to a partial leaching of some elements (alkali and alkaline earth metals). In conclusion, HTC seems to be an interesting alternative to torrefaction as it allows for the production of hydrochars suitable for gasification, and the recovery of molecules and minerals of interest. The interest and technical feasibility have been demonstrated in particular for biomasses with high moisture (agricultural crops) or with high pollutant contents (grounds of waste disposal).