Spelling suggestions: "subject:"boris""
1 |
High temperature studies of crystalline boric oxide and of hafnium borideBarnes, Dennis William, January 1961 (has links)
Thesis (M.S.)--University of Wisconsin--Madison, 1961. / Typescript. eContent provider-neutral record in process. Description based on print version record. Includes bibliographical references (leaf 24).
|
2 |
Pressure dependence of the apparent dissociation constants of carbonic and boric acids in seawaterCulberson, Charles Henry 06 March 1968 (has links)
Graduation date: 1968
|
3 |
Vaporization of B₂O₃ and other group three oxidesSoulen, John Richard. January 1955 (has links)
Thesis (Ph. D.)--University of Wisconsin--Madison, 1956. / Typescript. Vita. Abstracted in Dissertation abstracts, v. 16 (1956) no. 5, p. 883-884. eContent provider-neutral record in process. Description based on print version record. Includes bibliographical references (leaves 179-184).
|
4 |
Phase relations in the systems titania and titania--boric oxide /Beard, William Clarence January 1965 (has links)
No description available.
|
5 |
Investigation of tribological mechanisms of a boron additive in lubricants and fuel enhancerJohnsson, Elin January 2015 (has links)
The effect of using a boric acid based additive in lubricants and fuel enhancers was investigated in this study. Experiments were performed in a reciprocating and a continuous sliding ball-on-disk test equipment. Different oil types and temperatures were used. The aim of the experiments was to provide information about how these boron containing lubricants work in terms of chemistry and tribology. The surfaces after tribological contact were analyzed with Light Optical Microscopy (LOM), Vertical Scanning Interferometry (VSI), Scanning Electron Spectroscopy (SEM), Energy Dispersive X-ray Spectroscopy (EDS) and Secondary Ion Mass Spectroscopy (SIMS). The boric acid based additive and the temperature used affected both the friction and wear. A higher oil temperature resulted in wider wear tracks. Oil with boron additive seemed to lower the friction coefficient at temperatures above 50 °C, compared to the same oil without boric acid; the reference oil. The tests also indicated that friction coefficients as low as 0.05 can be achieved by using a boron additive layer on the disk surface together with PAO-oil. Tribofilms containing Zn, P, S, Mg and O were formed in the wear tracks at high temperatures for both the reference oil and oil with boron additive. Oxidized regions were found in the tracks created from tests at 25 °C. Tests with oil containing boron additive resulted in lower Zn concentrations in the tracks, which is an indication that the boric acid based additive hinders the formation of these Zn rich tribofilms. To summarize, both oils and fuel enhancers with boric acid can obtain lower friction coefficients compared to those without this additive. The role of boric acid in the tests performed, both regarding the tribology and chemistry, is not yet fully understood and more chemical investigations are needed.
|
6 |
The use of boron-containing additives for synthesis of anorthite ceramic powders/Kavalcı, Sedat. Akkurt, Sedat January 2006 (has links) (PDF)
Thesis (Master)--İzmir Institute of Technology, İzmir, 2006 / Keywords: Anorthite, boric acid, colemanite, statistical experimental design, X ray diffraction. Includes bibliographical references (leaves. 57-59).
|
7 |
Dissolution Of Colemanite And Crystallization Of Gypsum During Boric Acid Production In A Batch ReactorErdogdu, Anil 01 June 2004 (has links) (PDF)
One of the most commonly used boron compounds, boric acid, is produced by dissolving colemanite (2CaO× / 3B2O3× / 5H2O) in aqueous sulfuric acid whereby gypsum (CaSO4× / 2H2O) is formed as a byproduct and must be separated from the main product. This process consists of two steps, dissolution of colemanite and formation of gypsum. The amount of boric acid formed depends on the first step, dissolution of colemanite. In the latter step, gypsum crystals are formed and stay in the reaction mixture to grow up to a size large enough to be filtered out of the solution. Filtration of gypsum crystals is a crucial process in boric acid production because it affects the purity and crystallization of boric acid. In this study it is aimed to investigate the effects of particle size of colemanite, stirring rate and reaction temperature on the dissolution of colemanite, gypsum formation and particle size distribution of gypsum formed in the reaction of boric acid production.
Colemanite, sulfuric acid and distilled water were used as reactants for the boric acid production reaction in this study.The colemanite minerals were provided from a region of Emet, Kutahya, Turkey. Three types of colemanite minerals having different chemical composition and particle size were used. The sulfuric acid was supplied by Eti Holding A.S. Hisarcik 1 and Hisarcik 2 colemanites were crushed in a jaw crusher, ground in a hammer mill and then sieved. The sieve analysis was performed to learn the size distribution of Hisarcik 1 and Hisarcik 2 colemanite. Hisarcik 3 colemanite was brought from Emet Boric Acid Plant. The maximum diameter of the colemanite minerals was 150 & / #956 / m.
The experiments were performed at different particle sizes of colemanite (0-150, 0-250 and 250-1000 & / #956 / m), temperatures (70- 90 & / #61616 / C) and stirring rates (350-500 rpm). The photographs of gypsum crystals were taken. The boric acid and calcium ion concentrations were determined for each experiment. Also, the solid content of the solution in the reactor were measured. The dissolution of colemanite can be followed by monitoring the boric acid concentration change in the slurry. The crystallization of gypsum from the solution can be found from the calcium ion concentration in the solution. The crystallization kinetics of calcium sulfate dihydrate was studied. The growth of the gypsum crystals were examined under the light microscope and the particle size distribution of gypsum crystals were analyzed by of the laser diffraction instrument.
|
8 |
Mineral analysis and proximate composition of leaves of (Brassica oleracea var. acephala) in response to boron application in pot experimentsMohamed, Fatheya January 2018 (has links)
Thesis (MTech (Agriculture)--Cape Peninsula University of Technology, 2018. / Choumollier (narrow-stem kale) (Brassica oleracea, L.) has been progressively used in recent years as a supplementary forage harvest in many countries with a temperate climate. Boron (B) and calcium (Ca) are the two most important elements for supporting plant structure and function of plasma membranes. Boron nutrition is vital for obtaining high quality yields in vegetables. The main objective of this study was to evaluate the extent to which boric acid concentration can affect growth parameters (plant height, leaf numbers, chlorophyll levels, and leaf size) of Brassica olereacea var. acephala at different stages of growth and development. Treatment comprised of four concentrations of boron (0.3 mg/kg, 0.4 mg/kg, 0.5 mg/kg and 0.6 mg/kg). Yield and physiological growth responses were measured during the course of the study to ascertain effectiveness and influence of boron treatments on the test crops. Leaves of B. oleracea were harvested at weekly intervals (W1, W2, W3, W4 and W5) after each treatment regimen for approximate basic mineral analysis and composition. Soil pH did not vary much among the various orchard blocks tested, regardless of soil depth. Exchangeable cations Na+ and K+ levels did not vary significantly, but Ca2+ and Mg2+ levels fluctuated considerably among orchards analyzed. The Control Orchard exhibited a higher P content than the other orchards. Ca, Mg, Cu and B levels did not vary significantly among the orchards, but Na, Fe and Zn levels were markedly raised in the Orchard treated with 0.3 mg/kg boron) relative to the Control Orchard. Chlorophyll fluorescence was significantly dependent on the treatment dose of boron as compared to control. Chlorophyll fluorescence also increased significantly with the growth period, i.e., the duration following the initial treatment at all doses of boron. Boron at all did not significantly affect leaf count, leaf length and plant height. The work may add to the body of knowledge on the influence of boron on the physiological performance, mineral contents and proximate composition of leaves of the species. Furthermore, the findings may have important applications in achieving high quality yields in vegetable crops.
|
9 |
Towards environmentally friendly electrodeposition : using citrate based electrolytes to deposit nickel and nickel-ironPerry, Richard January 2016 (has links)
The production of magnetic materials is of great interest for use in the micro-fabrication industry. In particular, Permalloy (Ni80Fe20) is used in the production of micro-electromechanical systems (MEMS) due to its favourable magnetic properties (high relative permeability, low coercivity and high magnetic saturation). This leads to applications in devices such as inductors, transformers and micro-actuators. The electrodeposition of NiFe is also of fundamental electrochemical interest, as there is anomalous thermodynamic behaviour, with the less noble (iron) metal depositing preferentially to the more noble (nickel) metal. To enable consistent alloy deposition nickel and nickel-iron baths are currently almost exclusively based on boric acid. Boric acid has an important role in the deposition of NiFe films but its role(s) in the electro-deposition mechanism is (are) not wholly understood. Recently (2011) boric acid has been identified as a “substance of very high concern” based on the criteria established by EU chemical regulation, REACH. In anticipation of increased regulation an alternative was sought to provide a benign alternative to boric acid in the NiFe plating bath suitable for use in micro-fabrication. Initial work was performed to benchmark the performance of existing boric acid based electro-deposition baths. Cyclic voltammetry was performed, which demonstrated the deposition of nickel and nickel-iron from boric acid baths. Coulombic efficiencies up to 93 % were measured for the deposition of nickel using the electrochemical quartz crystal microbalance (EQCM) on platinum electrodes. For nickel-iron deposition control of the film composition was demonstrated on copper electrodes through varying the iron (II) concentration, current density and temperature. A citrate bath for the deposition of nickel-iron was then developed and characterised. Cyclic voltammetry was performed in these citrate baths demonstrating the deposition of nickel and nickel-iron. Optimal conditions for depositing Ni80Fe20 were demonstrated to be an elevated temperature (60 °C) with a current density of 20 mA cm-2 and a pH of 3. Using the EQCM the efficiency for nickel deposition was measured to be > 80 %. The effects of sodium saccharin and sodium dodecyl sulfate as additives were investigated; these were shown to influence morphology but not the coulombic efficiency. Decreasing the pH was shown to lower the efficiency of nickel deposition from the citrate bath. Comparisons of key properties were made between NiFe films deposited from a boric acid bath and the citrate bath developed in this work. Test structures were used to compare the strain in the films; no significant difference was found. For 2.2 μm thick Ni80Fe20 films the sheet resistance was measured using Greek cross structures as 0.078 ± 0.004 Ω/square for films deposited from the boric acid bath and 0.090 ± 0.006 Ω/square from the citrate bath. The magnetic saturation, Ms, was measured as 895 ± 66 emu cm-3 for deposits from the boric acid bath and 923 ± 111 emu cm-3 from the citrate bath. These again show no significant difference in these values within experimental error. Coercivities for these films were measured to be between 20 and 120 A m-1. In combination, this work demonstrates the development and characterisation of a new citrate based electrodeposition bath for nickel and nickel-iron. Similar chemical, electrical, mechanical and magnetic properties were found from films deposited from both baths, thus demonstrating the suitability of the citrate bath for the deposition of nickel-iron films in microfabrication.
|
10 |
Preservation of plywood against biological attack with low environmental impact using tannin-boron preservative / Protection à faible impact environnemental des contreplaqués avec des associations tannins-boreEfhamisisi, Davood 21 September 2015 (has links)
Une étude expérimentale a été menée afin de protéger des attaques biologiques des contreplaqués faits d'essences non durables (hêtre et peuplier), et ce, avec un faible impact environnemental. Des produits de protection à base de tannins et de bore, nouvellement développés afin de réduire le lessivage du bore, ont été sélectionnés pour ce but. Ce système a été utilisé pour protéger les contreplaqués selon deux approches : (1) au niveau de la colle pour remplacer les adhésives à base de formaldéhyde et coller les plis, (2) en traitement des plis avec des formulations plus diluées, les plis étant collés avec des adhésifs mélamine-urée-formaldéhyde. Les données expérimentales de cette thèse peuvent être classées en trois grands groupes : essais chimiques et thermomécaniques des colles tannin-bore, mesure des propriétés physiques et mécaniques, de la résistance biologique avant et après vieillissement des différents panneaux. Les essais chimiques sur les colles tannin/hexamine ont montré que l'addition de bore sous forme d'acide borique peut contribuer à plus de liaisons inter-flavonoids et à ouvrir les cycles pyranes ce qui accélère les réactions de polymérisation. Des analyses thermomécaniques sur les colles contenant des tannins de mimosa et de quebracho ont confirmé que l'addition d'acide borique (1) abaissait le temps et la température de prise, et (2) augmentait les valeurs du module d'élasticité de la colle. L'addition d'une quantité optimale d'acide borique dans la colle à base de tannin augmente les propriétés physiques et la résistance au cisaillement. Une charge excessive d'acide borique (10%) dans la colle est la cause de pertes de propriétés mécaniques et physiques. Bien qu'en faible quantité, l'introduction de l'acide borique dans la colle de tannin amène une protection efficace contre l'attaque fongique, même après un lessivage selon l'EN 1250-2. Les résultats des essais termites montrent que l'acide borique contenu dans la colle cause le plus faible taux de survie des insectes et de perte de masse, mais présentent un fort degré d'attaque selon une cotation visuelle. Aucune amélioration n'a été obtenue lors d'un essai de choix après lessivage. Les contreplaqués faits de plis traités par des solutions tannin-bore ont montré des résistances au cisaillement plus faibles, mais toujours dans les gammes requises pour des applications en atmosphère humide. Des résultats satisfaisants ont été obtenus par les réseaux polymères de tannins, même après une lessivage sévère, vis-à-vis de l'attaque fongique. Les contreplaqués faits de plis traités à l'acide borique seul ont présenté une sensibilité importante à l'attaque biologique après un lessivage. Les résultats des essais termites ont montré un faible taux de survie des insectes et de perte de masse, même après un lessivage sévère, pour les contreplaqués avec des plis traités par des systèmes tannin-bore. Les résultats d'un essai de choix a montré que les termites préféraient se nourrir des témoins quand l'alternative proposée était des échantillons traités avec des systèmes tannin-bore. / An experimental investigation was conducted to protect plywood panels made of perishable wood species (beech and poplar) against biological attacks with low environmental impact. The newly developed tannin-boron preservative which was proposed to reduce the leaching of borates was selected for this purpose. This system was used to protect plywood with two approaches: (1) in the glue line to replace formaldehyde based adhesives and gluing wood veneers, (2) pretreatment of wood veneers with the diluted formulations and bonded with melamine-urea-formaldehyde resin The research data in this thesis were obtained from three main groups of experiments: chemicals and thermomechanical testing on the tannin-boron resin, measuring physical and mechanical properties, and different biological tests before and after leaching processes. The chemicals testing on the tannin/hexamine adhesive showed that the addition ofboron, in the form of boric acid, can contribute more inter-flavonoid linkages and the opening of pyran rings which leads to the acceleration of polymerization reactions. Thermomechanical analysis on the adhesives of mimosa and quebracheo tannins confirmed that the addition of boric acid (1) lowered time and temperature of hardening, (2) and increased modulus of elasticity values of the adhesive. The addition of optimal boric acid into the tannin adhesive upgraded physical properties and tensile shear strength. An excess loading of boric acid (10%) in the glue line caused imperfect physical and mechanical features. Despite the low uptake of boric acid but its addition into the tannin glue provided effective resistance against fungal attack even after mild leaching test according to the EN 1250-2. The results of termites test showed that increase in the boric acid content of the adhesive caused the lower survival rate and the weight loss but samples underwent the high level of attack. No improvement against termite attack was obtained after leaching by a choice feeding test. The plywoods made of pretreated veneers by tannin-boron solutions showed partially lower tensile shear strength but still in the range of standards requirements for the humid applications. The satisfactory results were obtained even after severe leaching test against fungal attack with a strong polymeric network of tannin. The control plywoods made of pretreated veneers with boric acid alone solutions presented significant sensitivity against biological attack after leaching test. The results of termite tests showed the lower survival rate and the weight loss even after severe leaching test for the plywoods made of pretreated veneers with tannin-boron systems. The results of choice feeding test showed that termites preferred feeding from the controls when alternative samples were treated with the tannin-boron system. In general the evidence from this study suggests that tannin-boron system can significantly slow down the leaching of boron and it rendered high potential to preserve plywood.
|
Page generated in 0.3108 seconds