For many decades there has been a need in many industries to measure speed and position of ferrous gears. This is commonly done by converting passing gear teeth from trigger wheels to electrical impulses to calculate speed and angular position. By using Hall effect sensors or Giant Magnetoresistance sensors (GMR), a zero speed detection of gear teeth is possible while at the same time be cheap to produce and durable for harsh environments. A specially designed trigger-wheel (cogwheel created for measurements) with gear teeth in a specific pattern, exact position can be detected by using a dual sensor, even when no earlier information is available. The new design of trigger-wheel also makes this new method more accurate and universal compared to previous solutions. This thesis demonstrates and argues for the advantages of using a dual sensor for speed and angular position detection on gear wheels. Were one sensor do quantitative measurements for pattern detection in the teeth arrangements and the other sensor do qualitative measurements for position detection.

Made available in DSpace on 2016-12-08T17:19:18Z (GMT). No. of bitstreams: 1 Resumo Eduardo P Ferreira.pdf: 31057 bytes, checksum: e12b3482b1be4ee60ab99c2523cdfc02 (MD5) Previous issue date: 2012-08-23 / Coordenação de Aperfeiçoamento de Pessoal de Nível Superior / In this present conducted in wear resistance nodular cast iron subjected to heat treatment at different temperatures isothermal austempering treatment (340 ° C and 320 °), corresponding to the materials of Classes 3 and 4 of ASTM A897, compared with nodular quenched and tempered with same level hardness. The objective was to develop alternatives for future studies on new materials applied camshaft valve internal combustion engines. For this wear tests were conducted pin-on-disc, using as alumina ball against the body, thus considering zero wear on the counter-body. All cast irons tested under the conditions of this work had hardness in the range 40-46 HRc. It was found in analyzes by scanning electron microscopy the effect of graphite nodules and the matrix material, the wear mechanisms, thus observing the effect that stress concentrator nodes imposes the metallic matrix. The damage to the material surface was initially with crack of the matrix surrounding graphite nodules, they generally located subsurface, moreover, it can be seen that the nodules torn metal matrix acted as a lubricant for testing, and the sites left by lumps were previously coated particles detached from the matrix. It was found with the results of wear tests the performance of austempered ductile iron in comparison with the quenched and tempered for distances exceeding 1000 m slip, thereby qualifying the ADI as an alternative material for future studies in manufacturing valve camshafts. / Apresenta-se neste trabalho um estudo de resistência ao desgaste realizado em ferros fundidos nodulares submetidos ao tratamento térmico de austêmpera em duas temperaturas isotérmicas de tratamento (340°C e 320°), correspondendo aos materiais das classes 3 e 4 da norma ASTM A897, comparativamente com o nodular temperado e revenido de nível de dureza similar. Objetivou-se desenvolver alternativas para estudos futuros em novos materiais aplicados a eixo comando de válvula de motores a combustão interna. Para isto foram realizados ensaios de desgaste pino-sobre-disco, utilizando como contra corpo esfera de alumina, considerando assim desgaste zero no contra-corpo. Todos os ferros fundidos ensaiados nas condições deste trabalho tiveram dureza na faixa de 40 46 HRc. Constatou-se em análises por microscopia eletrônica de varredura o efeito dos nódulos de grafita e da matriz do material, sobre os mecanismos de desgaste, observando assim o efeito concentrador de tensão que os nódulos impõe a matriz metálica. O dano à superfície do material ocorreu inicialmente com o tricamento da matriz em torno dos nódulos de grafita, estes geralmente localizados subsuperficialmente, além disto, pode se observar que os nódulos arrancados da matriz metálica atuaram como lubrificantes ao ensaio, e os sítios deixados pelos nódulos foram recobertos por partículas anteriormente desprendidas da matriz. Constatou-se com os resultados dos ensaios de desgaste o bom desempenho do ferro nodular austemperado em comparação com o temperado e revenido para distâncias de deslizamento superiores a 1000 m, qualificando assim o ADI como material alternativo para futuros estudos na fabricação de eixos comando de válvula.

Tomáš ŠTÁBL Design of Gear Timing Mechanism for SI Engine MT, IAE, 2009, 62 pp., 27 fig. This master thesis is concerning the valve train proposal of the spark ignition engine for sports purposes. Antecedent to the actual proposal is the division and retrieval of the modern valve trains, the valve train acting forces description, division and description of the individual valve-lift curve parts , valve springs and the dynamic models of the valve train. In the thesis there are designed the valve lift curves with the continuous course of acceleration, valve springs and valve springs natural oscillations damper for engine Honda CBR 929RR. The dynamic analysis of valve train approach is performed.

Diploma thesis deals with the dynamic analysis of OHV pushrod valve train drive of the old-new conception of 6-cylinder tractor engine with 24 valves made by Zetor Tractors, a.s.. There is a requirement to create an analytical model and design valve springs for the engine. The work also points to the current analytical methods of appropriate simulation software used in automotive industry.

This thesis provides an overall evaluation of the concept of inline injection pump for pressure 120 MPa. The name of this pump is "Mj" and it is a product of the Motorpal, a.s. company. This thesis also contains an analysis of the contact pressures between the cam lobe and the pumping element's roller tappet. This includes comparing three different shapes of the roller and their influence on the magnitude of contact pressures. Calculations of the plunger helix and of the fuel delivery's impact on the relative position of plunger are also present.

Im Vortrag wird die Vorgehensweise zur Modellierung des Ventiltriebs eines Einzylinder-Motorradmotors beschrieben. Dieser setzt sich aus zwei gebauten, wälzgelagerten Nockenwellen zusammen. Die Ventile werden über Schlepphebel betätigt. Das Hauptaugenmerk liegt dabei auf den Pressverbindungen zwischen Nocken und Welle sowie auf den Wälzlagerungen. Um die Belastungszustände zu ermitteln ist eine detaillierte Simulation nötig. Diese Mehrkörpersimulation wird in Mathcad mit Hilfe eines eigenen Lösers durchgeführt.

No description available.

Die Weiterentwicklung von Verbrennungsmotoren ist geprägt von einer Steigerung der Effizienz, optimaler Betriebslaststeuerung, einer Absenkung des spezifischen Verbrauchs und der Erfüllung geltender Abgasemissionsgesetzgebung. Die Optimierung des Ladungswechsels spielt dabei eine entscheidende Rolle. Eine Möglichkeit den Ladungswechsel optimal zu beeinflussen, ist der Einsatz von variablen Ventiltrieben zur Veränderung der Ventilhubbewegung sowie zur Verstellung der Steuerzeiten. thyssenkrupp Dynamic Components entwickelt und stellt Schiebenockensysteme als diskret schaltbare Ventiltriebsysteme her, welche die verschiedenen Ventilhubanforderungen über unterschiedliche Nockenprofile auf dem Schiebeelement nebeneinander abbilden können. Im Entwicklungs- und Auslegungsprozesses kommt eine Simulation des Bewegungs-, Beschleunigungs- und Abbremsverhaltens sowie der Kraftverläufe beim Verstellvorgang mittels einer Mehrkörpersimulation (MKS) in der Software alaska/ModellerStudio zum Einsatz. In diesem Beitrag wird das MKS-Modell des Schiebelements sowie der Abgleich des Modells mit Versuchen vorgestellt. Es folgt eine Darstellung von Optimierungsmöglichkeiten bereits in der Simulationsumgebung, bei denen die Kontaktnormalkräfte und Beschleunigungen in mehreren Iterationsschleifen auf den gewünschten Anwendungsfall angepasst werden können. Unter Berücksichtigung der Fertigungs- und Lagertoleranzen sowie des Verschleißverhaltens kann das System mit diesem Simulationstool bereits virtuell abgeprüft werden. / The advancement of internal combustion engines is characterized by an increase in efficiency, optimum operating load control, a reduction in specific consumption and compliance with applicable exhaust emission legislation. Optimization of the charge change plays a decisive role in this. One way of optimally influencing the charge change is to use variable valve trains to change the valve lift and adjust the timing. thyssenkrupp Dynamic Components develops and manufactures sliding cam systems as discretely switchable valve train systems that can feature the various valve lift requirements side by side via different cam profiles on the sliding element. A simulation of the motion, acceleration and deceleration behavior as well as the force curves during the sliding process by means of a multi-body simulation (MBS) in the alaska/ModellerStudio is applied in the development and design process. This presentation shows the MBS model of the sliding cam and the comparison of the model with test results. Various optimization options in the simulation environment present, how the contact normal forces and accelerations can be adapted in several iteration loops to the desired application. Taking into account the manufacturing and bearing tolerances as well as the wear behavior, this simulation tool allows to virtually check the sliding cam system.