Thesis (Ph. D.)--University of Texas at Austin, 2008. / Vita. Includes bibliographical references.

Thesis (Ph. D.)--University of Wyoming, 2006. / Title from PDF title page (viewed on April 16, 2008). Includes bibliographical references (p. 157-174).

Petrophysical properties are fundamental to understanding fluid flow processes in hydrocarbon reservoirs. Special Core Analysis (SCAL) routinely used in industry are time-consuming, expensive, and often destructive. Alternatively, easily available thin section data is lacking the representation of pore space in 3D, which is a requisite for generating pore network models (PNM) and computing petrophysical properties. In this study, these challenges were addressed using a numerical SCAL workflow that employs pore volume reconstruction from thin section images obtained from confocal laser scanning microscopy (CLSM). A key objective is to investigate methods capable of 2D to 3D reconstruction, to obtain PNM used for the estimation of transport properties. Representative thin sections from a well-known Middle-Eastern carbonate formation were used to obtain CLSM images. The thin-sections were specially prepared by spiking the resin with UV dye, enabling high-resolution imaging. The grayscale images obtained from CLSM were preprocessed and segmented into binary images. Generative Adversarial Networks (GAN) and Two-Point Statistics (TPS) were applied, and PNM were extracted from these binary datasets. Porosity, Permeability, and Mercury Injection Porosimetry (MIP) on the corresponding core plugs were conducted and an assessment of the properties computed from the PNM obtained from the reconstructed 3D pore volume is presented. Moreover, the results from the artificial pore networks were corroborated using 3D confocal images of etched pore casts (PCE). The results showed that based on visual inspection only, GAN outperformed TPS in mimicking the 3D distribution of pore scale heterogeneity, additionally, GAN and PCE outperformed the results of MIP obtained by TPS on the Skeletal-Oolitic facies, without providing a major improvement on more heterogeneous samples. All methods captured successfully the porosity while absolute permeability was not captured. Formation resistivity factor and thermal conductivity showcased their strong correlation with porosity. The study thus provides valuable insights into the application of 2D to 3D reconstruction to obtain pore network models of heterogeneous carbonate rocks for petrophysical characterization for quick decision. The study addresses the following important questions: 1) how legacy thin sections can be leveraged to petrophysically characterize reservoir rocks 2) how reliable are 2D to 3D reconstruction methods when predicting petrophysical properties of carbonates.

The purpose of this study was first to develop a method by which a detailed porosity classification system could be utilized to understand the relationship between pore/pore-throat geometry, genetic porosity type, and facies. Additionally, this study investigated the relationships between pore/pore-throat geometry, petrophysical parameters, and reservoir performance characteristics. This study focused on the Jurassic Smackover reservoir rocks of Grayson field, Columbia County, Arkansas. This three part study developed an adapted genetic carbonate pore type classification system, through which the Grayson reservoir rocks were uniquely categorized by a percent-factor, describing the effect of diagenetic events on the preservation of original depositional texture, and a second factor describing if the most significant diagenetic event resulted in porosity enhancement or reduction. The second part used petrographic image analysis and mercury-injection capillary pressure tests to calculate pore/pore-throat sizes. From these data sets pore/pore-throat sizes were compared to facies, pore type, and each other showing that pore-throat size is controlled by pore type and that pore size is controlled primarily by facies. When compared with each other, a pore size range can be estimated if the pore type and the median pore-throat aperture are known. Capillary pressure data was also used to understand the behavior of the dependent rock properties (porosity, permeability, and wettability), and it was determined that size-reduced samples, regardless of facies, tend to show similar dependent rock property behavior, but size-enhanced samples show dispersion. Finally, capillary pressure data was used to understand fluid flow behavior of pore types and facies. Oncolitic grainstone samples show unpredictable fluid flow behavior compared to oolitic grainstone samples, yet oncolitic grainstone samples will move a higher percentage of fluid. Size-enhanced samples showed heterogeneous fluid flow behavior while the size-reduced samples could be grouped by the number of modes of pore-throat sizes. Finally, this study utilized petrographic image analysis to determine if 2- dimensional porosity values could be calculated and compared to porosity values from 3-dimensional porosity techniques. The complex, heterogeneous pore network found in the Grayson reservoir rocks prevents the use of petrographic image analysis as a porosity calculation technique.

Carbonate reservoirs may have a variety of porosity types created by depositional, diagenetic, and fracture processes. This leads to the formation of complex pore systems, and in turn creates heterogeneities in reservoir performance and quality. In carbonate reservoirs affected by diagenesis and fracturing, porosity and peremeability can be independent of depositional facies or formation boundaries; consequently, conventional reservoir characterization methods are unreliable for predicting reservoir flow characteristics. This thesis provides an integrated petrographic, stratigraphic, and petrophysical study of the 'Canyon Reef' reservoir, a Pennsylvanian phylloid algal mound complex in the Horseshoe atoll. Core descriptions on three full-diameter cores led to the identification of 5 distinct depositional facies based on fundamental rock properties and biota. Fifty-four thin sections taken from the core were described are pores were classified using the Humbolt modification of the Ahr porosity classification. In order to rank reservoir quality, flow units were established on the basis of combined porosity and permeability values from core analysis. A cut off criterion for porosity and permeability was established to separate good and poor flow units. Ultimately cross sections were created to show the spatial distribution of flow units in the field.

The application of carbon-dioxide injection for enhanced oil recovery and/or sequestration purposes has gained impetus in the last decade. It is known that well test analysis plays a crucial role on getting information about reservoir properties, boundary conditions, etc. Although there are some studies related to the well test analysis in the fractured reservoirs, most of them are not focused on the carbon dioxide injection into the reservoir. Naturally fractured reservoirs (NFR) represent an important percentage of the worldwide hydrocarbon reserves and current production. Reservoir simulation is a fundamental technique in characterizing this type of reservoirs. Fracture properties are often not clear due to difficulty to characterize the fracture systems. On the other hand, well test analysis is a well known and widely applied reservoir characterization technique. Well testing in NFR provides two significant characteristic parameters, storativity ratio (&omega / ) and interporosity flow coefficient (&lambda / ). The storativity ratio is related to fracture porosity. The interporosity flow coefficient can be linked to the shape factor which is a function of fracture spacing. In this study, the effects of fracture and fluid flow factors (geometry, orientation and flow properties) on pressure and pressure derivative behavior are studied by applying a reservoir simulation model. Model is utilized mainly for the observation of multiphase flow effects in CO2 flooded fractured reservoirs. Several runs are conducted for various ranges of the aforementioned properties in the CO2 flooded reservoir. Results of well test analysis are compared to the input data of simulation models on a parameter basis.

The purpose of this study was first to develop a method by which a detailed porosity classification system could be utilized to understand the relationship between pore/pore-throat geometry, genetic porosity type, and facies. Additionally, this study investigated the relationships between pore/pore-throat geometry, petrophysical parameters, and reservoir performance characteristics. This study focused on the Jurassic Smackover reservoir rocks of Grayson field, Columbia County, Arkansas. This three part study developed an adapted genetic carbonate pore type classification system, through which the Grayson reservoir rocks were uniquely categorized by a percent-factor, describing the effect of diagenetic events on the preservation of original depositional texture, and a second factor describing if the most significant diagenetic event resulted in porosity enhancement or reduction. The second part used petrographic image analysis and mercury-injection capillary pressure tests to calculate pore/pore-throat sizes. From these data sets pore/pore-throat sizes were compared to facies, pore type, and each other showing that pore-throat size is controlled by pore type and that pore size is controlled primarily by facies. When compared with each other, a pore size range can be estimated if the pore type and the median pore-throat aperture are known. Capillary pressure data was also used to understand the behavior of the dependent rock properties (porosity, permeability, and wettability), and it was determined that size-reduced samples, regardless of facies, tend to show similar dependent rock property behavior, but size-enhanced samples show dispersion. Finally, capillary pressure data was used to understand fluid flow behavior of pore types and facies. Oncolitic grainstone samples show unpredictable fluid flow behavior compared to oolitic grainstone samples, yet oncolitic grainstone samples will move a higher percentage of fluid. Size-enhanced samples showed heterogeneous fluid flow behavior while the size-reduced samples could be grouped by the number of modes of pore-throat sizes. Finally, this study utilized petrographic image analysis to determine if 2- dimensional porosity values could be calculated and compared to porosity values from 3-dimensional porosity techniques. The complex, heterogeneous pore network found in the Grayson reservoir rocks prevents the use of petrographic image analysis as a porosity calculation technique.

Highly fractured carbonate reservoirs are a class of reservoirs characterized by high conductivity fractures surrounding low permeability matrix blocks. In these reservoirs, wettability alteration is a key method for recovering oil. Water imbibes into the matrix blocks upon water flooding if the reservoir rock is water-wet. However, many carbonate reservoirs are oil-wet. Surfactant solution was used to enhance spontaneous imbibition between the fractures and the matrix by both wettability alteration and ultra-low interfacial tensions. The first part of this study was devoted to determining the wettability of reservoir rocks using Amott-Harvey Index method, and also evaluating the performance of surfactants on wettability alteration, based on the contact angle measurement and spontaneous imbibition rate and ultimate oil recovery on oil-wet reservoir cores. The reservoir rocks have been found to be slightly oil-wet. One cationic surfactant BTC8358, one anionic surfactant and one ultra-low IFT surfactant formulation AKL-207 are all found to alter the wettability towards more water-wet and promote oil recovery through spontaneous imbibition. The second part of the study focused on the parameters that affect wettability alteration by surfactants. Some factors such as core dimension, permeability and heterogeneity of porous medium are evaluated in the spontaneous imbibition tests. Higher permeability leads to higher imbibition rate and higher ultimate oil recovery. Heterogeneity of core samples slows down the imbibition process if other properties are similar. Core dimension is critical in upscaling from laboratory conditions to field matrix blocks. The imbibition rate is slower in larger dimension of core. Further, we investigated the effects of EDTA in surfactant-mediated spontaneous imbibition. Since high concentration of cationic divalent ions in the aqueous solution markedly suppresses the surfactant-mediated wettability alteration, EDTA improved the performance of surfactant in the spontaneous imbibition tests. It is proposed in the thesis that surfactant/EDTA-enhanced imbibition may involve the dissolution mechanism. More experiments should be conducted to verify this mechanism. The benefits of using EDTA in the surfactant solution include but not limited to: altering the surface charge of carbonate to negative, producing the in-situ soap, reducing the brine hardness, decreasing the surfactant adsorption, and creating the water-wet area by dissolving the dolomite mineral. / text

The goal of this work is to change the wettability of a carbonate rock from oil wet-mixed-wet towards water-wet at high temperature and high salinity. Only simple surfactant systems (single surfactant, dual surfactants) in dilute concentration were tried for this purpose. It was thought that the change in wettability would help to recover more oil during secondary surfactant flood as compared to regular waterflood. Three types of surfactants, anionic, non-ionic and cationic surfactants in dilute concentrations (<0.2 wt%) were used. Initial surfactant screening was done on the basis of aqueous stability at these harsh conditions. Contact angle experiments on aged calcite plates were done to narrow down the list of surfactants and spontaneous imbibition experiments were conducted on field cores for promising surfactants. Secondary waterflooding was conducted in cores with and without the wettability altering surfactants. It was observed that barring a few surfactants, most were aqueous unstable by themselves at these harsh conditions. Dual surfactant systems, a mixture of a non-ionic and a cationic surfactant increased the aqueous stability of the non-ionic surfactants. One of the dual surfactant system, a mixture of Tergitol NP-10 and Dodecyl trimethyl ammonium bromide, proved very effective for wettability alteration and could recover 70-80% of OOIP during spontaneous imbibition. Secondary waterflooding with the wettability altering surfactant (without alkali or polymer) increased the oil recovery over the waterflooding without the surfactants (from 29% to 40% OOIP). Surfactant adsorption calculated during the coreflood showed an adsorption of 0.24 mg NP-10/gm of rock and 0.20 mg DTAB/gm of rock. A waterflood done after the surfactant flood revealed change in the relative permeability before and after the surfactant flood suggesting change in wettability towards water-wet. / text

Water injection has been practiced to displace the hydrocarbons towards adjacent wells and to support the reservoir pressure at or above the bubble point. Recently, waterflooding in sandstone reservoirs, as secondary and tertiary modes, proved to decrease the residual oil saturation. In calcareous rocks, water from various resources (deep formation, seawater, shallow beds, lakes and rivers) is generally injected in different oil fields. The ions interactions between water molecules, salts ions, oil components, and carbonate minerals are still ambiguous. Various substances are usually added before or during water injection to enhance oil recovery such as dilute surfactant. Various methods were used including surface charge (zeta potential), static and dynamic contact angle, core flooding, inductively coupled plasma spectrometry, CAT scan, and geochemical simulation. Limestone and dolomite particles were prepared at different wettability conditions to mimic the actual carbonate reservoirs. In addition to seawater and dilute seawater (50, 20, 10, and 1 vol%), formation brine, shallow aquifer water, deionized water and different crude oil samples were used throughout this study. The crude oil/water/carbonates interactions were also investigated using short and long (50 cm) limestone and dolomite rocks at different wettability and temperature conditions. The aqueous ion interactions were extensively monitored via measuring their concentrations using advanced analytical techniques. The activity of the free ions, complexes, and ion pairs in aqueous solutions were simulated at high temperatures and pressures using OLI electrolyte simulation software. Dilute seawater decreased the residual oil saturation in some of the coreflood tests. Hydration and dehydration processes through decreasing and increasing salinity showed no impact on calcite wettability. Effect of individual ions (Ca, Mg, and Na) and dilute seawater injection on oil recovery was insignificant in compare to the dilute surfactant solutions (0.1 wt%). The reaction mechanisms were confirmed to be adsorption of hydroxide ions, complexes and ion pairs at the interface which subsequently altered the surface potential from positive to negative. Results in this study indicate multistage waterflooding can enhance oil recovery in the field under certain conditions. Mixed streams simulation results suggest unexpected ions interactions (NaCO3-1, HSO4-1, NaSO4-1 and SO4-2) with various activities trends especially at high temperatures.