Thesis (M.Sc. (Agriculture)) --University of Limpopo,2008 / Cellulose is regarded as the most abundant polymer in nature and the first on which X-ray investigations had been performed, a year after the discovery of diffraction of X-rays on crystalline materials in 1912. It is one of the most abundant and important polymers on the planet. It comprises of four allomorphs, cellulose Iβ, II, III and IV1 and IV2 of which Iβ and II are the most stable and industrially important. Cellulose I is the native form of cellulose. Molecular dynamics (MD) simulations have been carried out to study the structural and mechanical properties of cellulose, cellulose Iβ, II, III and IV1 and IV2 bulk systems. Simulations were carried out using Polymer Consistence Force Field (PCFF) and Compass force field in conjunction with the Discover simulation program at various temperatures. We used molecular dynamics simulation to obtain a better insight about temperature dependence of cellulose. Further investigations on mechanical properties of this material at various temperatures were carried out. Using pair correlation functions g(r) or radial distribution functions (rdf’s) we were able to investigate phase transitions wherein as the temperature was increased we observed peak broadening. These enabled us to study the similarities between the structures investigated. Also studied was water uptake in celluloses by way of introducing water at different concentrations. Analysis of lattice parameters compared reasonably well with the experimental. Lattice parameters were calculated using PCFF and they compared well with results found using Compass force field. Calculation of temperature and pressure dependence on bulk systems has been done and it was noted that as the pressure increases the lattice parameters decrease. / National Research Foundation and CSIR

<p>The primary cell wall is a complex multipolymer system whose composite structure has been mostly determined from chemical and biochemical studies. Although the primary cell wall serves a central role, with regard to the connective properties of fibres, knowledge about the interactions among the polymers, when it comes to the mechanical properties, is very limited. The physical properties of the polymers, i.e. their elastic and viscous deformations, as well as the ultrastructure of the polymers, i.e. the interactions among the polymers in the outer fibre wall layers that lead to this behaviour, are still not fully understood.</p><p>The aim of this study was to examine how the different wood polymers, viz. lignin, protein, pectin, xyloglucan and cellulose, interact in the outer fibre wall layers of the spruce wood tracheid. The initial objective was to separate an enriched primary cell wall material from a first stage TMP, by means of screening and centri-cleaning. From this material, consisting of the primary cell wall (P) and outer secondary cell wall (S1) materials, thin sheets were prepared and analysed using a number of different analytical methods. The major measuring technique used was dynamic Fourier transform infra-red (FT-IR) spectroscopy in combination with dynamic 2D FT-IR spectroscopy. This technique is based on the detection of small changes in molecular absorption that occur when a sinusoidally stretched sample undergoes low strain. The molecular groups affected by the stretching respond in a specific way, depending on their environment, while the unaffected molecular groups provide no response to the dynamic spectra, by producing no elastic or viscous signals. Moreover, the dynamic 2D FT-IR spectroscopy provides useful information about various intermolecular and intramolecular interactions, which influence the reorientability of functional groups in a polymer material.</p><p>Measurements of the primary cell wall material, using dynamic FT-IR spectroscopy, indicated that strong interactions exist among lignin, protein and pectin, as well as among cellulose, xyloglucan and pectin in this particular layer. This was in contrast to the secondary cell wall, where interactions of cellulose with glucomannan and of xylan with lignin were dominant. It was also indicated that the most abundant crystalline cellulose in the primary cell wall of spruce wood fibres is the cellulose Iβ allomorph, which was also in contrast to the secondary cell wall, where the cellulose Iα allomorph is more dominant. The presence of strong interactions among the polymers in the primary cell wall and, especially, the relatively high content of pectin and protein, showed that there is a very good possibility of selectively attacking these polymers in the primary cell wall. The first selective reaction chosen was a low degree of sulphonation, applied by an impregnation pretreatment of chips with a very low charge of sodium sulfite (Na2SO3). This selective reaction caused some structural modification of the lignin, a weakening of the interactions between lignin;pectin, lignin;protein and pectin;protein, as well as an increased softening of the sulphonated primary cell wall material, when compared to the unsulphonated primary cell wall material. All this resulted in an increased swelling ability of the material.</p>

The primary cell wall is a complex multipolymer system whose composite structure has been mostly determined from chemical and biochemical studies. Although the primary cell wall serves a central role, with regard to the connective properties of fibres, knowledge about the interactions among the polymers, when it comes to the mechanical properties, is very limited. The physical properties of the polymers, i.e. their elastic and viscous deformations, as well as the ultrastructure of the polymers, i.e. the interactions among the polymers in the outer fibre wall layers that lead to this behaviour, are still not fully understood. The aim of this study was to examine how the different wood polymers, viz. lignin, protein, pectin, xyloglucan and cellulose, interact in the outer fibre wall layers of the spruce wood tracheid. The initial objective was to separate an enriched primary cell wall material from a first stage TMP, by means of screening and centri-cleaning. From this material, consisting of the primary cell wall (P) and outer secondary cell wall (S1) materials, thin sheets were prepared and analysed using a number of different analytical methods. The major measuring technique used was dynamic Fourier transform infra-red (FT-IR) spectroscopy in combination with dynamic 2D FT-IR spectroscopy. This technique is based on the detection of small changes in molecular absorption that occur when a sinusoidally stretched sample undergoes low strain. The molecular groups affected by the stretching respond in a specific way, depending on their environment, while the unaffected molecular groups provide no response to the dynamic spectra, by producing no elastic or viscous signals. Moreover, the dynamic 2D FT-IR spectroscopy provides useful information about various intermolecular and intramolecular interactions, which influence the reorientability of functional groups in a polymer material. Measurements of the primary cell wall material, using dynamic FT-IR spectroscopy, indicated that strong interactions exist among lignin, protein and pectin, as well as among cellulose, xyloglucan and pectin in this particular layer. This was in contrast to the secondary cell wall, where interactions of cellulose with glucomannan and of xylan with lignin were dominant. It was also indicated that the most abundant crystalline cellulose in the primary cell wall of spruce wood fibres is the cellulose Iβ allomorph, which was also in contrast to the secondary cell wall, where the cellulose Iα allomorph is more dominant. The presence of strong interactions among the polymers in the primary cell wall and, especially, the relatively high content of pectin and protein, showed that there is a very good possibility of selectively attacking these polymers in the primary cell wall. The first selective reaction chosen was a low degree of sulphonation, applied by an impregnation pretreatment of chips with a very low charge of sodium sulfite (Na2SO3). This selective reaction caused some structural modification of the lignin, a weakening of the interactions between lignin;pectin, lignin;protein and pectin;protein, as well as an increased softening of the sulphonated primary cell wall material, when compared to the unsulphonated primary cell wall material. All this resulted in an increased swelling ability of the material. / QC 20101123