Currently, there is a high demand for lightweight aerospace materials, driven by the desire to provide enhanced fuel efficiency by reducing vehicular weight. Aluminum alloys are attractive due to their excellent mechanical properties and high strength to weight ratios. Powder metallurgy (PM), which converts metal powder into a high performance product, presents an alternative to traditional forming techniques, which are often unable to provide adequate dimensional tolerances. The challenge is to determine if aluminum PM alloys and technologies can be successfully employed within aerospace applications. This research focuses on the PM processing technologies (die compaction, cold isostatic pressing (CIP), and spark plasma sintering (SPS)) of two alloys, PM2024 and PM7075. Processing parameters were assessed using attributes such as density, hardness, and tensile properties. Both powders showed comparable densities and tensile properties to their wrought equivalents. Ultimately, the groundwork was laid for future research into these alloys and their processing methods.

Cette étude s’intéresse à l’amélioration et l’allégement des protections balistiques transparentes. L’utilisation conventionnelle de verre assure une haute efficacité face à un projectile, cependant associée à une masse élevée et à une forte épaisseur du blindage. Le remplacement de la face avant par une céramique polycristalline, telle que le spinelle MgAl2O4, assure un gain de performance et une réduction du volume de l’assemblage. L’élaboration de ce matériau requiert la combinaison d’une haute qualité optique dans le domaine du visible et de propriétés mécaniques élevées. Dans ce travail, l’application d’un frittage naturel sous vide d’une poudre commerciale de haute pureté a permis de limiter l’introduction d’impuretés néfastes à la transparence et la croissance granulaire. Une étape supplémentaire de pressage isostatique à chaud s’est montrée nécessaire à l’élimination des pores résiduels et à l’obtention de spinelles transparents de haute qualité optique (80% à 400-800 nm, e = 2 mm, Ø21 mm). Une étude de la microstructure avant et après post-traitement a permis de mettre en relation la taille des grains et des pores avant post-frittage avec la croissance granulaire observée pendant ce traitement. Une optimisation du procédé a ainsi pu être mise en place afin de limiter l’augmentation de la taille des grains et obtenir une microstructure homogène (~ 12 μm). Après un changement des dimensions des échantillons réussi (e = 4 mm, Ø60 mm), différents spinelles à propriétés microstructurales et mécaniques distinctes ont été sélectionnés pour une évaluation en conditions balistiques. / This work focuses on the improvement and the lightening of transparent ballistic armours. The conventional use of glass provides high efficiency against a projectile, however associated with a heavy and thick armour. The replacement of the strike face by a polycrystalline ceramic, such as MgAl2O4 spinel, leads to a performance gain and a decrease of the protection volume. The development of this material requires the combination of a high optical quality in the visible domain and high mechanical properties. In this work, pressureless sintering under vacuum of a high purity commercial powder allowed to minimize the addition of impurities, detrimental to the transparency, and the grain growth phenomenon. An additional step of hot isostatic pressing was necessary to eliminate residual porosity and to obtain transparent spinel with high optical quality (80% at 400-800 nm, t = 2 mm, Ø21 mm). An analysis of the microstructure before and after the post-treatment made it possible to determine the link between the grain and pore sizes before post-sintering and the observed grain growth during this treatment. An optimisation of the process was established in order to restrain the grain size increase, and thus to obtain a homogeneous microstructure (~ 12 μm). After a successful up-scaling of the samples (t = 4 mm, Ø60 mm), several spinel samples with distinctive microstructural and mechanical properties were selected in order to evaluate their performances through ballistic tests.