1 |
Heat transfer and pressure drop characteristics of smooth tubes at a constant heat flux in the transitional flow regimeHallquist, Melissa 28 September 2012 (has links)
Due to constraints and changes in operating conditions, heat exchangers are often forced to operate under conditions of transitional flow. However, the heat transfer and flow behaviour in this regime is relatively unknown. By describing the transitional characteristics it would be possible to design heat exchangers to operate under these conditions and improve the efficiency of the system. The purpose of this study was to experimentally measure the heat transfer and pressure drop characteristics of smooth tubes at a constant heat flux in the transitional flow regime. The measurements were used to describe the flow behaviour of this regime and attempt to develop a correlation that can be used in the design of a heat exchanger. An experimental set-up was developed, consisting of an overall set-up, a removable test section as well as a controller, which ensured a uniform heat flux boundary. The test section allowed for the measurement of the temperature along the length of the test section, the pressure drop across the test section, the heat flux input and the flow rate. The measurements were used to determine the heat transfer coefficients and friction factor of the system. Three test sections were developed with outer diameters of 6, 8 and 10 mm in order to investigate the influence of heat exchanger size. Each test section was subject to four different heat flux cases of approximately 1 500, 3 000, 4 500 and 6 000 W/m2. The experiments covered a Reynolds number range of 450 to 10 300, a Prandtl number range of 4 to 7, a Nusselt number range of 2.3 to 67, and a Grashoff number range of 60 to 23 000. Good comparison was found between the measurements of this experiment and currently available literature. The experiments showed a smooth transition from laminar to turbulent flow with the onset of transition dependent on the heat flux of the system and with further data capturing, a correlation can be found to describe the Nusselt number in the transitional flow regime. / Dissertation (MEng)--University of Pretoria, 2011. / Mechanical and Aeronautical Engineering / unrestricted
|
2 |
Friction factors and nusselt numbers for laminar flow in ducts / Daniel Petrus Rocco VenterVenter, Daniel Petrus Rocco January 2009 (has links)
By using the finite element method to solve the appropriate momentum and energy equations the friction factors and Nusselt numbers for fully developed laminar flow were determined for one- and two-dimensional flow systems. The Nusselt numbers were determined for domain boundaries subjected to a constant heat flux (H1) or a constant surface temperature (T) around the computational boundaries and in the axial directions. C++ programs, that were rewritten and extended from previous programs, were used to solve the laminar flow and to determine the values. The required wall shear stresses and heat fluxes were directly obtained for a duct as part of the primary finite-element solution; these values were then used to determine the Nusselt number and friction factor for the specific duct. The computations were performed for circular-, annular-, trapezoidal-, rectangular- and triangular ducts. Special emphasis was placed on trapezoidal ducts since only a limited number of studies have been performed on trapezoidal duct shapes and none of these studies employed the finite element method. Excellent agreement was found when the determined values were compared with the values reported in the literature. In general, the agreement of the values improved as the number of elements was increased. It was, therefore, concluded that the methods used in this study yielded friction factors and Nusselt numbers that are very accurate and usable. / Thesis (M.Ing. (Mechanical Engineering))--North-West University, Potchefstroom Campus, 2009.
|
3 |
Friction factors and nusselt numbers for laminar flow in ducts / Daniel Petrus Rocco VenterVenter, Daniel Petrus Rocco January 2009 (has links)
By using the finite element method to solve the appropriate momentum and energy equations the friction factors and Nusselt numbers for fully developed laminar flow were determined for one- and two-dimensional flow systems. The Nusselt numbers were determined for domain boundaries subjected to a constant heat flux (H1) or a constant surface temperature (T) around the computational boundaries and in the axial directions. C++ programs, that were rewritten and extended from previous programs, were used to solve the laminar flow and to determine the values. The required wall shear stresses and heat fluxes were directly obtained for a duct as part of the primary finite-element solution; these values were then used to determine the Nusselt number and friction factor for the specific duct. The computations were performed for circular-, annular-, trapezoidal-, rectangular- and triangular ducts. Special emphasis was placed on trapezoidal ducts since only a limited number of studies have been performed on trapezoidal duct shapes and none of these studies employed the finite element method. Excellent agreement was found when the determined values were compared with the values reported in the literature. In general, the agreement of the values improved as the number of elements was increased. It was, therefore, concluded that the methods used in this study yielded friction factors and Nusselt numbers that are very accurate and usable. / Thesis (M.Ing. (Mechanical Engineering))--North-West University, Potchefstroom Campus, 2009.
|
4 |
ANALYSIS OF TRANSPORT MODELS AND COMPUTATION ALGORITHMS FOR FLOW THROUGH POROUS MEDIAAL-AZMI, BADER SHABEEB 12 May 2003 (has links)
No description available.
|
Page generated in 0.0771 seconds