The removal of lead, copper and cadmium ions from aqueous streams using lecithin enhanced micro filtration with 0.2μm pore size tubular ceramic membranes has been investigated. Measurements of the surface tension at varying lecithin concentrations were carried out to determine the critical micelle concentration (CMC) of lecithin and the effects of lead ions, mixtures of lead and copper ions, and mixtures of lead, copper and cadmium ions in solutions on the CMC of lecithin. The zeta potential and the effects of the single and multiple metal ions on the zeta potential of lecithin were also investigated. The influence of lecithin concentrations, cross flow velocity and transmembrane pressure on the rejections and steady state permeate flux behaviours were examined. The CMC of lecithin was found to be 9 grl. An increase in metal ion concentration caused a decrease in the CMC and an increase in the zeta potential of lecithin solutions, suggesting the binding of the metal ions onto the lecithin. An increase in lecithin concentration was found to improve metal ions removal. Lecithin showed preference for the metal ions in the order Pb2+ > Cd 2+ > Cu 2+. Metal ion removal was influenced more by lecithin concentration and less by transmembrane pressure and cross flow velocity. The steady state permeate flux and rejection behaviours have been explained by microscopic phenomena and a mathematical model has been developed to predict the steady state permeate flux. The lecithin concentration that remains in the permeate was less than 9% of the feed solution. The study has shown that lecithin enhanced micro filtration is a technically suitable technique for removal of lead, copper and cadmium ions in aqueous solution.

Two new homologous series of amphiphiles–five long-chain, three-headed amphiphiles [3CCb14, 3CCb16, 3CCb18, 3CCb20, 3CCb22; CH3(CH2)n-1OCONHC(CH2CH2COOH)3, n = 14, 16, 18, 20, 22], and six branched-chain, three-headed amphiphiles [3CCb1(7,7), 3CCb1(8,8), 3CCb1(9,9), 3CCb1(10,10), 3CCb1(11,11), 3CCb1(12,12); (CH3(CH2)n-1)2CHOCONHC(CH2CH2COOH)3, n = 7, 8, 9, 10, 11, 12]–were synthesized. The synthesis of the 3CCbn series was accomplished in two steps from Weisocyanate™ and the long chain alcohol in good yields of chromatographed products (65–81%). The 3CCb1(n,n) series was similarly synthesized from Weisocyanate™ and the two-tailed symmetric alcohol (produced from a reaction of alkyl magnesium bromide and ethyl formate) in good yields of chromatographed products (71–84%). CMC data were collected by pendent-drop technique for the 3CAmn, 3CCbn, 3CUrn, and 3CCb1(n,n) series of amphiphiles to establish the concentration required for detergency. The triethanolammonium salt provided better solubility and higher CMCs of these amphiphiles than the potassium salt. All amphiphilic series tested lowered the solution surface tension from ~ 72 mN/m to ~ 50–55 mN/m, indicating that these amphiphiles are less surface active than typical surfactants such as sodium dodecyl sulfate. The CMCs for the 3CAmn series were found to decrease in value from 2 × 10⁻² M (3CAm15) to 2 × 10⁻³ M (3CAm21) in a linear fashion. The CMCs for the 3CCbn series were found to decrease in value from 7 × 10⁻³ M (3CCb16) to 0.4 × 10⁻³ M (3CCb22) in a linear fashion. The CMCs for the 3CUrn series were found to decrease in value from 2 × 10⁻³ M (3CUr18) to 1 × 10⁻³ M (3CUr22) in a linear fashion. Due to discrepancies in several of the IFT vs. log concentration plots for the previous homologous series of amphiphiles, the CMC data was collected using a pyrene fluorescence measurement technique. The data from the pyrene fluorescence technique seems likely to be more accurate, indicating that surface tension may not be the most reliable method for determining the CMC of these amphiphiles. The CMCs (as determined by pyrene fluorescence) for the 3CAmn series were found to decrease in value from 2 × 10⁻² M (3CAm15) to 2 × 10⁻³ M (3CAm21) in a linear fashion. The CMCs for the 3CCbn series were found to decrease in value from 7 × 10⁻³ M (3CCb16) to 0.3 × 10⁻³ M (3CCb22) in a linear fashion. The CMCs for the 3CUrn series were found to decrease in value from 7 × 10⁻³ M (3CUr16) to 0.2 × 10⁻³ M (3CUr22) in a linear fashion. In both the surface tension and the pyrene fluorescence techniques, the shortest chain length homologues (3CAm13, 3CCb14, and 3CUr14) did not show a break up to the limits of solubility. The CMCs as determined by surface tension for the 3CCb1(n,n) series were found to decrease in value from 0.5 × 10⁻³ M (3CCb1(9,9)) to 0.02 × 10⁻³ M (3CCb1(12,12)) in a linear fashion. The 3CCb1(8,8) and 3CCb1(7,7) amphiphiles did not show a CMC break up to the limits of solubility. The 3CCb1(12,12) showed an unusually steep decrease in surface tension over a very narrow range of concentration. There is considerable doubt as to the accuracy of the 3CCb1(11,11) data, and the CMCs for these two-tailed amphiphiles needs to be measured by a second method as was done for the single-tail series to verify the CMCs of all the two-tail homologues. Activity (minimal inhibitory concentrations, MICs) for the 3CAmn, 3CCbn, 3CUrn, 3CCb1(n,n), 2CAmn, and 2CCbn series was measured against several different bacteria, mycobacteria, yeast, and fungi. Additionally, anti-HIV and cytotoxicity data was collected for the 3CAmn, 3CCbn, and 3CUrn series. Greatest inhibition was typically seen from the 18–20 carbon tail length homologues of each series (3CAm19–3CAm21, 3CCb18–3CCb20, 3CUr18–3CUr20, 2CAm19–2CAm21, and 2CCb18–2CCb20). Inoculum density affected the activity of our earlier studies, and selected organisms were retested to obtain the intrinsic activity. 3CUr18 and 3CAm19 proved most effective against Mycobacterium smegmatis, with MIC99 = 6.3 μM @ 10⁵ CFU/mL inoculum density. 3CCb20 was most effective against Mycobacterium marinum with MIC99 = 16 μM @ 10⁵ CFU/mL inoculum density. 3CAm19, 3CCb18, and 3CUr18 all showed equivalent activity against Mycobacterium chelonae with MIC99 = 17 μM @ 10⁵ CFU/mL inoculum density. Against Staphylococcus aureus, the 2CAm21 was most effective, with MIC90 = 2.0 μM @ 10⁵ CFU/mL inoculum density. 3CCb20 was most effective against MRSA with MIC90 = 2.9 μM @ 10⁵ CFU/mL inoculum density. The two-tailed analogs (3CCb1(n,n), 3CUr(n,n), and 3CUr1(n,n)) typically showed little to no activity against the tested microorganisms. Comparison of MIC to CMC is a relative measure of safety of a drug candidate. All single-tail amphiphiles showed ratios of MIC/CMC of 16–126, with a ratio of 100 or better being optimal. The ratios for the two-tail amphiphiles ranged from 0.39 to 2.9. / Ph. D.

Rhamnolipid (RL) biosurfactants have been considered "green" alternatives to synthetic surfactants. Here, systematic studies of monorhamnolipids (mRLs) and their synthetic analogues are performed to characterize their interfacial and solution behaviors as surfactants. Chemical structure-surface activity relationships of rhamnolipids were probed using surface tension measurements on RLs and a series of their synthetic analogues designed by "truncation modification." Based on our study on RLs and the rationally-designed RL analogues, the key structural factor responsible for the excellent surface activity performance of rhamnolipids is the presence of the rhamnose moiety in the headgroup. As a result, rhamnopyranosides (RhEs), the simplest surfactants with a rhamnose moiety in the headgroup, show surface activity comparable to the bioproduced mRLs. The purified mixture of mRLs harvested from Pseudomonas aeruginosa ATCC 9027 was mixed with a nonionic surfactant Tween-20 (TW) and studied by surface tension measurements at pH 8. The experimental values of CMC show deviation from the theoretical values predicted by ideal solution theory, which is hypothesized to be due to a shape change from rod-shaped to spherical as the mole fraction of TW is increased. The hypothesis about the shape change is supported by dynamic light scattering results, regular solution theory, and packing parameter theory. Polarization modulated-infrared reflection-absorption spectroscopy (PM-IRRAS) has been used to characterize the orientation of the synthetic rhamnolipid Rha-C18-C18 at the air-water interface. Although rhamnolipids exhibit pH-dependent micellization, their orientation at the air-water interface is not affected by pH. The average tilt angle of their alkyl chains is determined to be ~45° at a surface pressure π = 40 mN/m which decreases to 36° when Pb²⁺ is present in the subphase. Assisted by molecular modeling, the packing of mRLs at the air-water interface is believed to be dominated by the packing of their large hydrophilic headgroups. Finally, the adsorption isotherm of mRLs on hydrophobic polyethylene surfaces was generated by ATR-FTIR from solutions of different pH, which were then fit to a Frumkin adsorption model to yield the thermodynamic adsorption parameters, the adsorption equilibrium constant and the interaction parameter. mRLs strongly adsorb to d-PE, and the adsorption is pH dependent.

In this article, a multiple-responsive polymer micelles system was constructed by using ionic bond to link the hydrophobic tetraphenylthiophene (TP) fluorophores, which possess the property of aggregation-induced emission enhancement (AIEE), with the hydrophilic poly(N-isopropyl acrylamide) (PNIPAM). The susceptibility of the ionic ammonium-sulfonate (Am-Sul) bonds towards metal ions, acid and base triggered the AIEE-operative fluorescence (FL) response. To exercise the idea, PNIPAM with sulfonate terminal was primarily prepared to react with TP-derivatives functionalized with ammonium groups to generate polymer complex of TP-PNIPAM. When in water, the polymer complex TP-PNIPAM formed micelles with the aggregated TP core interconnecting the hydrophilic PNIPAM shell by the ionic Am-Sul bonds. With the operative AIEE effect, the aggregated TP core of the micelles fluoresced but upon the additions of metal ions, acid and base, the ionic bonds dissociated to result in the collapse of the micelles and the FL quenching. A novel fluorogenic sensor capable to respond to multi-stimuli was therefore constructed. Amphiphilic micelle systems with the hydrophilic poly(N-isopropyl amide) (PNIPAM) shell and the hydrophobic tetraphenylthiophene (TP), which has the novel aggregation-induced emission enhancement (AIEE) feature, core inter-connected by ionic bonds were prepared in this study to explore the AIEE-operative emission response towards critical micelle concentration (CMC) and lower critical solution temperature (LCST). To exercise the idea, TP functionalized ammonium cations and PNIPAM with terminal sulfonate group were individually prepared and mixed together to yield three amphiphilic TP-PNIPAM complexes with different hydrophobic TP to the hydrophilic PNIPAM (x/y) ratios. When in aqueous solution, TP-PNIPAMs form micelles with the aggregated TP core, which emits strongly due to the operative AIEE effect, encompassed by the PNIPAM shell. The resultant CMC and LCST of the TP-PNIPAM micelles can be varied by changing the hydrophobic to the hydrophilic x/y ratio and can be monitored by the AIEE-dominant fluorescence responses towards concentration and temperature variables.

Submitted by Biblioteca da Faculdade de Farmácia (bff@ndc.uff.br) on 2017-03-17T17:34:41Z No. of bitstreams: 1 Nicoletti, Caroline Deckmann [Dissertação, 2015].pdf: 2492191 bytes, checksum: 2cc1df517b27092f16baf567910a3c1a (MD5) / Made available in DSpace on 2017-03-17T17:34:41Z (GMT). No. of bitstreams: 1 Nicoletti, Caroline Deckmann [Dissertação, 2015].pdf: 2492191 bytes, checksum: 2cc1df517b27092f16baf567910a3c1a (MD5) / Coordenação de Aperfeiçoamento de Pessoal de Nível Superior / A papaína é uma enzima proteolítica utilizada no tratamento de feridas. É parcialmente solúvel em água e tem baixa estabilidade em preparações farmacêuticas, dessa forma os géis com concentrações de papaína acima de 1% podem apresentar precipitados. O presente trabalho teve como objetivo o desenvolvimento de géis de papaína a 4% (p/p) usando tensoativos como agente solubilizante. Como fase inicial do estudo realizou-se a determinação da Concentração Micelar Crítica (CMC) por meio da medida de tensão superficial de geis de papaína a 4,0% (p/p) com e sem L-cisteína e diferentes concentrações de polissorbato 80. Novas preparações foram desenvolvidas usando-se concentrações de polissorbato e L-cisteína que resultavam na completa solubilização da papaína. O estudo de estabilidade dos géis de papaína a 4,0% (p/p) com polissorbato 80 foi planejado e executado a partir de desenho experimental fatorial 33 em amostras armazenadas sob refrigeração por 30 dias. As variáveis independentes estipuladas foram concentração de L-cisteína, concentração de polissorbato 80 e o tempo de armazenagem; a variável dependente avaliada foi a concentração de papaína ativa. Todas as amostras foram analisadas quanto à manutenção das características sensoriais e físico-químicas. Durante o período de avaliação as preparações conservaram-se como géis homogêneos, mantendo-se estáveis quanto aos valores de pH, de viscosidade e de estabilidade termodinâmica. Estas amostras não apresentaram mudanças no seu comportamento reológico. As preparações estudas apresentaram concentrações de papaína ativa entre 90 e 110% apos 24 horas de preparo, mas não foi possível a manutenção desta atividade durante o período de estudo. As avaliações estatísticas decorrentes do desenho experimental fatorial resultaram em gráficos de superfície de resposta e de contorno, que demonstraram que o tempo é o fator de maior influência sobre a perda da atividade da papaína nas preparações em gel. A L-cisteína interfere favoravelmente para a manutenção da atividade, mas sua ação isolada é incapaz de sobrepor-se ao efeito do tempo. A associação da L-cisteína e do polissorbato 80 também apresenta ação favorável a manutenção da atividade enzimática, que se torna evidente somente nas maiores concentrações estudadas para estes adjuvantes / Papain is a proteolytic enzyme used in the treatment of wounds. It is partially soluble in water and has low stability in pharmaceutical preparations thus gels with papain above 1% concentration may have precipitated. This study aimed to the development of papain gels at 4% (w / w) using surfactants as solubilizing agent. As the initial phase of study was carried out to determine the critical micellar concentration (CMC) by action of surface tension of papain gels at 4.0% (w / w) with and without L-cysteine and different concentrations of polysorbate 80. New preparations were developed using concentrations of polysorbate and Lcysteine resulted in complete solubilization of papain. The stability study of papain gels at 4.0% (w / w) polysorbate 80 was planned and carried out from 33 factorial experimental design for samples stored under refrigeration for 30 days. The independent variables were prescribed concentration of L-cysteine, concentration of polysorbate 80 and the storage time; the evaluated dependent variable was the concentration of active papain. All samples were analyzed for the maintenance of sensorial and physicochemical characteristics. During the evaluation period preparations presented as homogeneous gels, remaining stable as the pH, viscosity and thermodynamic stability. These samples showed no changes in their rheological behavior. The preparations studied showed ative papain concentrations between 90 and 110% after 24 hours of preparation, but it was not possible to maintain this activity over the study period. The statistical evaluations resulting from the factorial experimental design resulted in response surface graphs and contour, showing that time is the most influential factor on the loss of papain activity in preparations gel. L-cysteine favorably affects the maintenance of the activity, but its action alone is unable to override the effect of the time. The combination of Lcysteine and polysorbate 80 also presents favorable action to maintain the enzyme activity, which becomes evident only at the highest concentrations investigated for these adjuvants

Presented diploma thesis deals with drug encapsulation of Sulfathiazole (STA) in thermosensitive hydrogel composed of amphiphilic fibrous molecules of copolymer poly(D,L-lactide-co-glycolide)-block-poly(ethylene glycol)-block-poly(D,L-lactide-co-glycolide) (PLGA-PEG-PLGA). In the experimental part, the structure of the micelles which is dependent on the concentration of the default copolymer, was thoroughly described. The method of dynamic light scattering (DLS) was used to dimensionally characterize the micellar size in aqueous solution. At the same time, the Cryo-Transmission Electron Microscopy (Cryo-TEM) imaging technique confirmed the transition from spherical micelles to fibrous branched structures with a number of topological interactions. The change in viscoelastic properties of micellar hydrogel after addition of STA was studied by rheological analysis. The studied triblock copolymer appears to be a suitable tissue engineering material as a carrier in applications for targeted drug delivery and tissue regeneration.

The kinetics of the reaction catalyzed by acyl-CoA: sn-glycerol-3-phosphate O-acyltransferase solubilized from Euglena gracilis microsomes were examined. For myristoyl-, palmitoyl-, stearoyl-, and oleoyl-CoAs, the initial reaction rates rose with increasing substrate concentration up to an optimal concentration that varied from 18.5 to 25 μ M, well above the respective critical micelle concentrations. At higher substrate concentrations, reaction was progressively inhibited. Arachidoyl-CoA was a relatively poor substrate for the acyltransferase, and substrate inhibition was not seen with it. Km values for acyl-CoAs ranged from 13 to 20 μ M while the corresponding V values varied almost 40-fold. Bovine serum albumin, among other effects, caused a change in the kinetic pattern of the reaction acyl-CoA dependency. Both acyl-CoA micelles and albumin-bound acyl-CoA were substrates. The binding of palmitoyl- and oleoyl-CoA was 2.7 and 1.5 mol, respectively, per mol of albumin. The critical micelle concentration of palmitoyl-CoA under the reaction conditions was shown by low angle light scattering photometry to be 7.1 p.M. The sn-glycerol 3-phosphate concentration dependency of the acyltransferase initial velocity exhibited Michaelis-Menten kinetics with Km values of 1.3 and 2.9 mM in the presence of 12.5 and 25 μM palmitoyl-CoA, respectively. The substrate analogues sn-glyceraldehyde 3-phosphate and dihydroxyacetone phosphate inhibited the reaction.

In this project, we synthesized a new homologous series of five long-chain, two-headed amphiphiles [2CAm13, 2CAm15, 2CAm17, 2CAm19, 2CAm21; CH3(CH2)n-1CONHC(CH3)(CH2CH2COOH)2, n = 13, 15, 17, 19, 21]. The synthesis of the 2CAmn series was accomplished in four steps. The first step involves a reaction of nitroethane and two equivalents of tert-butyl acrylate to create the nitrodiester synthon [O2NC(CH3)(CH2CH2COOtBu)2] by successive Michael additions. The second step in the synthesis consists of a reduction of nitrodiester with H2 and Raney nickel to give the diesteramine [H2NC(CH3)(CH2CH2COOtBu)2]. The third step is the condensation of an acid chloride with diesteramine to give an alkanamido diester [2EAmn; CH3(CH2)n-1CONHC(CH3)(CH2CH2COOtBu)2, n = 13, 15, 17, 19, 21]. The final step is the removal of the tert-butyl protecting groups to give 2CAmn. Critical micelle concentration measurements were collected by the pendant drop method for measuring surface tension for a series of triethanolamine/2CAmn solutions to establish the concentration required for detergency. The CMCs for the 2CAmn series were found to decrease in value from 3.0 Ã 10â 2 M (2CAm13) to 1.7 Ã 10â 4 M (2CAm21) in a linear fashion [log CMC = (â 0.28 ± 0.01)n + (2.2 ± 0.1)]. The CMCs for the 2CAmn series falls in between the CMCs for three series of homologues three-headed amphiphiles (3CAmn, 3CCbn, 3CUrn) and the CMCs for fatty acids, with fatty acids having the lowest CMCs. Antibacterial activity (minimal inhibitory concentrations, MICs) for a series of homologous dendritic two-headed amphiphiles and three series of homologous, three-headed amphiphiles against Staphylococcus aureus and methicillin-resistent S. aureus (MRSA) were measured by broth microdilution to compare the effect of chain length and, hence, hydrophobicity. Inoculum density affected antibacterial activity of the 2CAmn series against both S. aureus and MRSA. MIC measurements at different cell densities showed that activity decreased with higher cell densities. For all four series, the MICs were relatively flat at low inoculum densities. This flat region defines the intrinsic activity, MIC0. The MIC0 results revealed that inoculum density, chain-length, and hydrophobicity all influenced antibacterial activity and that activity correlates strongly with clogp, an established measure of hydrophobicity. The most hydrophobic members from each homologous series exhibited antibacterial activity. The most active homologue of the 2CAmn series was 2CAm21 with MIC0 of 2.0 ± 1.0 and 3.2 ± 1.0 μM against S. aureus and MRSA, respectively. The CMCs and MIC0s of the two- and three-headed amphiphiles were compared for both S. aureus and MRSA to gauge the effect that micelles may have on activity. Amphiphile 2CAm19 has the largest ratio between CMC and MIC0 (CMC/MIC0 = 205) against S. aureus and 3CUr20 has the largest ratio (CMC/MIC0 = 339) against MRSA. These ratios suggest that micelle formation is not a mechanism of action for anti-Staphylococcal activity. / Master of Science

This project is about the synthesis of homologous series of two-headed, long-chain amphiphiles (the 2CCbn series, where n = 16, 18, 20, 22, 30, 5α-cholestan-3Ã -ol). The 2CCbn series was synthesized in five steps. The first step involves a reaction of nitroethane and two equivalents of tert-butyl acrylate to form nitrodiester by successive Michael addition reaction. The second step is the reduction of nitrodiester with Raney nickel to form aminodiester. The third step involves a reaction of aminodiester with di-tert-butyl dicarbonate [(Boc)2O] to form isocyanatediester. The fourth step is addition of iscocyanatediester with aliphatic alcohol to give alkyl carbamate diester (2ECbn) series. The fifth step is the removal of the tert-butyl protecting group to give the 2CCbn series. The critical micelle concentrations (CMC) were measured by the pyrene-based fluorescent probe method. The pyrene excited at 345 nm and fluoresces with maxima at 374 nm (I1) and 385 nm (I3). The stock solution and the dilution series for each amphiphiles were made in 0.9% triethanolamine solution. The CMCs were measured at two pH ~9.2 and 7.4. The CMCs were determined by plotting I1/I3 vs. concentrations. The CMCs were decreasing with increasing chain length. The CMCs for the 2CCbn series are lower than the 3CCbn series but higher than the fatty acids. The minimal inhibitory concentrations were measured against Staphylococcus aureus and methicillin-resistant Staphylococcus aureus. These strains were grown on BHIB+S with 5% triethanolamine. The MICs of the 2CCbn series amphiphiles were measured by using microtiter plate reader and by looking turbidity. The cutoff effect was found for the 2CCbn series. The MIC decreased up to C20 chain length and started rising for C22. The 2CCb18 (MICâ 2.2 µg/mL) of the 2CCbn series was the most effective amphiphile against S. aureus and MRSA. The CMC/MIC ratio was used to determine the safety of an amphiphile as a drug use. The amphiphile 2CCb18 has given the largest safety ratio (CMC/MIC = 273) against S. aureus and MRSA. It suggests that micelle formation is not a mechanism of action for anti-Staphylococcal activity. / Master of Science

Vliv hyaluronanu na micelizaci tenzidů byl studován různými fyzikálně-chemickými metodami. Byly zvoleny dva kationaktivní tenzidy, a to tetradecyltrimethylammonium bromid (TTAB) a cetyltrimethylammonium bromid (CTAB). Metoda izotermické titrační kalorimetrie byla využita pro stanovení entalpie micelizace, tenziometrie popisuje povrchové vlastnosti daných vzorků. Byl sledován také vliv různé molekulové hmotnosti použitého hyaluronanu a délka alkylového řetězce tenzidu na agregační chování daného systému. Výsledkem jsou hodnoty kritické micelární nebo agregační koncentrace tenzidu. V neposlední řadě se diskutuje využití agregátů hyaluronan-tenzid jako možné nosiče pro cílenou distribuci léčiv.