Hydrogen is seen as the green fuel of the future for the aeronautical sector allowing to reduce the carbon footprint of commercial aviation. It is well established that the release of carbon emissions triggers global warming. Aviation, like many other industries, must reduce them. This study aims to integrate cryogenic hydrogen storage onboard an existing aircraft and study two different propulsion systems, namely hydrogen combustion and fuel cells. A cryogenic tank was modelled and then designed to fit in the fuselage of an A321. Two configurations were studied, one consisting of one tank at the rear and the other with two tanks, one at the front and one at the aft. The result showed a significant variation of the centre of gravity for the rear tank configuration, whether the airplane is empty or with payload. Among the two propulsion systems investigated, hydrogen combustion requires less of a technological leap than hydrogen fuel cell aircraft. The limitation would be the range due to the lack of volume onboard the aircraft to store the hydrogen fuel. But this new type of propulsion could lay the groundwork for future fuel cell aircraft. The fuel cells technology still needs to improve its power density to compete with current engines but would o er more efficient aircraft and therefore greater range.

This research aims to investigate the influence of 3D through-thickness stitching on the gas permeability and transverse microcracking of cryogenically cycled carbon/epoxy composites. 3D through-thickness stitching can be used to improve the interlaminar properties of polymer matrix composites (PMCs) and produce lightweight, unitized structures for cryogenic storage tanks. To fully utilize stitched composite structures for these applications, their inherent gas permeability challenges must be understood. Therefore, in this study, the stitched composites' damage evolution and gas permeability was experimentally characterized under a) pure thermal stress, b) thermal and uniaxial mechanical stress, and c) thermal and biaxial mechanical stress. Helium gas permeability was measured for each specimen at room or cryogenic temperatures under a mechanically strained state following the thermo-mechanical cycles. Optical microscopy was used to measure microcrack densities and monitor their evolution through the thickness of the composite specimens. Thin plies, graphene nanoplatelets (GNP) modified resin, and a hybrid barrier layer comprising of both were incorporated in the stitched specimens as barrier layers to reduce their gas permeability. The dependence of gas permeability of stitched composites on the mechanical strain, test temperature, and load history was evaluated and correlated to microcrack density. A significant reduction in permeability and damage evolution (transverse microcracks and delaminations) was obtained for all thermo-mechanical cases using the hybrid barrier layer laminate. Additionally, the permeability was several orders of magnitude lower than the allowable. Overall, the hybrid barrier layer shows tremendous promise as a viable barrier layer for stitched/unstitched composites undergoing thermo-mechanical fatigue involving a cryogenic environment.

Aviation industry is continuously growing especially for very long distance flights due to the globalisation of local economies around the world and the explosive economic growth in Asia. Reducing the time of intercontinental flights from 16-20 hours to 4 hours or less would therefore make the, already booming, ultra-long distance aviation sector even more attractive. To accomplish this drastic travel time reduction for civil transport, hypersonic cruise aircraft are considered as a potential cost-effective solution. Such vehicles should also be fuelled by liquid hydrogen, which is identified as the only viable propellant to achieve antipodal hypersonic flight with low environmental impact. Despite considerable research on hypersonic aircraft and hydrogen fuel, several major challenges should still be addressed before such airliner becomes reality. The current thesis is therefore motivated by the potential benefit of hydrogen-fuelled hypersonic cruise vehicles associated with their limited state-of-the-art.Hypersonic cruise aircraft require innovative structural configurations and thermal management solutions due to the extremely harsh flight environment, while the uncommon physical properties of liquid hydrogen, combined with high and long-term heat fluxes, introduce complex design and technological storage issues. Achieving hypersonic cruise vehicles is also complicated by the multidisciplinary nature of their design. In the scope of the present research, appropriate methodologies are developed to assess, design and optimize the thermo-structural model and the cryogenic fuel tanks of long-range hydrogen-fuelled hypersonic civil aircraft. Two notional vehicles, cruising at Mach 5 and Mach 8, are then investigated with the implemented methodologies. The design analysis of light yet highly insulated liquid hydrogen tanks for hypersonic cruise vehicles indicates an optimal gravimetric efficiency of 70-75% depending on insulation system, tank wall material, tank diameter, and flight profile. A combination of foam and load-bearing aerogel blanket leads to the lightest cryogenic tank for both the Mach 5 and the Mach 8 aircraft. If the aerogel blanket cannot be strengthened sufficiently so that it can bear the full load, then a combination of foam and fibrous insulation materials gives the best solution for both vehicles. The aero-thermal and structural design analysis of the Mach 5 cruiser shows that the lightest hot-structure is a titanium alloy construction made of honeycomb sandwich panels. This concept leads to a wing-body weight of 143.9 t, of which 36% accounts for the wing, 32% for the fuselage, and 32% for the cryogenic tanks. As expected, hypersonic thermal loads lead to important weight penalties (of more than 35%). The design of the insulated cold structure, however, demonstrates that the long-term high-speed flight of the airliner requires a substantial thermal protection system, such that the best configuration (obtained by load-bearing aerogel blanket) leads to a titanium cold design of only 4% lighter than the hot structure. Using aluminium 7075 rather than titanium offers a further weight saving of about 2%, resulting in a 135.4 t wing-body weight (with a contribution of 23%, 25%, 18% and 34% from the TPS, the wing, the fuselage, and the cryogenic tanks respectively). Given the design hypotheses, the difference in weight is not significant enough to make a decisive choice between hot and cold concepts. This requires the current methodologies to be further elaborated by relaxing the simplifications. Investigation of the thermal protection must be extended from one single point to different regions of the vehicle, and the TPS thickness and weight should be considered in the structural sizing of the cold design. More generally, the design process should be matured by including additional (static, dynamic and transient) loads, special structural concepts, multi-material configurations and other parameters such as cost and safety aspects. / Doctorat en Sciences de l'ingénieur et technologie / This thesis was conducted in co-tutelle between University of Sydney and Université Libre de Bruxelles.Professor Dries Verstraete was my supervisor at the University of Sydney (so as a member of SydneyUni), but is automatically registered here as a member of ULB because he worked at ULB almost ten years ago.Ben Thornber is also a member of the University of Sydney but the application does not save it for an unknown reason. / info:eu-repo/semantics/nonPublished