Native fishes have become an increasingly important concern when designing fish passable culverts. Many operational culverts constrict waterways which increase velocities and prevent upstream passage of small fish species. The current method to ensure fish passage is to match the average cross sectional velocity to the sustained swim speed of the fish. This study investigates the passage rates of leatherside chub (Lepidomeda aliciae) and speckled dace (Rhinichthys osculus) at three sites (an arch culvert with substrate bottom, box culvert with bare bottom, and a stream section with no culvert) located on Salina Creek near Salina, UT. It was found that fish were able to pass through all of the sites. However, fish were able to take advantage of the habitat within the culvert that had a substrate bottom more effectively than within the culvert that had no substrate within the barrel. This was reflected in population density estimates at each of the three test sites for each species. It was also found that the substrate at the arch culvert and stream sites scaled with the fish measured in this study. The D50 and D84 were 44 and 205 mm at the arch culvert site and 26 and 126 mm at the stream site. The average fish length was 76 mm for the chub and 64 mm for the dace. It is recommended that (1) a culvert size that produces a velocity equal to the prolonged swim speed of target fish in the near boundary region (2 cm above the bed) be used in the future, and (2) substrate that scales with the target fish species be placed in the culvert barrel.

No description available.

No description available.

No description available.

No description available.

No description available.

京都大学 / 0048 / 新制・課程博士 / 博士(工学) / 甲第21736号 / 工博第4553号 / 新制||工||1710(附属図書館) / 京都大学大学院工学研究科社会基盤工学専攻 / (主査)教授 木村 亮, 教授 岸田 潔, 准教授 木元 小百合 / 学位規則第4条第1項該当 / Doctor of Philosophy (Engineering) / Kyoto University / DFAM

No description available.

No description available.

The performance of joints in buried gravity flow pipelines are important since failure of these elements can affect the structural capacity of soil-pipe systems and reduce their longevity. Currently, there are no clear guidelines to design joints for gravity flow pipelines and therefore their design is based on semi-empirical methods. It is necessary to identify and quantify the demands that act across joints when subjected to service loading conditions to establish adequate design guidelines. Such demands will vary depending on the type of joint, type of pipe, burial and loading conditions. Therefore work is needed to investigate the influence of these conditions on the performance of joints. Full-scale laboratory tests have been performed on rigid (reinforced concrete) and flexible (corrugated steel and thermoplastic) pipelines to investigate the response of their joints when buried and subjected to surface loading. The joints investigated are either ‘moment-release’ joints (those that accommodate rotation and reduce the longitudinal bending moments close to zero), or ‘moment-transfer’ joints (those that limit rotation and transfer longitudinal bending moments from one pipe to the next). These experiments evaluate the influence of different cover depths, loading locations, and installation conditions on the response of the joints. Additionally, the performance of each joint when the pipeline was buried with shallow cover and subjected to surface loads up to and beyond fully factored loads were also investigated. Furthermore, three-dimensional finite element analyses of a gasketed bell and spigot joint in a buried reinforced concrete pipeline subjected to surface loading have been developed employing material properties and joint rotational characteristics experimentally obtained. The data obtained from the experimental and computational studies are used to evaluate joint performance and to identify key demands (shear force and rotation or moment) acting across them. In addition, the different patterns of vertical displacement along rigid and flexible pipes were established. It was found that the stiffness of the pipeline, the geometry of the joint, the loading and burial conditions influence the response (and therefore the demands) of the joints examined. Finally, recommendations are provided regarding development of structural design methods for these pipeline and joint systems. / Thesis (Ph.D, Civil Engineering) -- Queen's University, 2012-12-29 12:47:31.826