Geogrid reinforcement can improve the performance of pavements by stiffening the aggregate base material and decreasing pavement deformations. Understanding the effects of cyclic loading on the modulus of geogrid-reinforced base materials would help engineers better anticipate actual increases in the modulus of aggregate base materials under given traffic loads. The objective of this laboratory research was to investigate the effects of cyclic loading on the resilient modulus, the modulus to peak axial stress, the elastic modulus, and the modulus at 2 percent strain of geogrid-reinforced aggregate base materials. The scope of the research included two aggregate base materials (Wells Draw and Springville) having different particle-size distributions and particle angularity. Geogrid-reinforced and unreinforced specimens were subjected to conditioning periods consisting of cyclic loading ranging from 10 to 10,000 cycles. Immediately following cyclic loading, all specimens were tested using the quick shear portion of the American Association of State Highway and Transportation Officials T 307 (Determining the Resilient Modulus of Soils and Aggregate Materials). Specimen preparation involved material weigh-outs, compaction, and membrane applications. Specimen testing in the loading machine consisted of two testing portions, including cyclic loading and quick shear testing. The cyclic loading data were used to calculate the resilient modulus on 200-cycle intervals throughout the duration of the conditioning period. The quick shear data were used to calculate the peak axial stress, the modulus to peak axial stress, the elastic modulus and the modulus at 2 percent strain. For the Wells Draw material, the resilient modulus increases by 11 percent for the specimens with geogrid and increases by 8 percent for the specimens without geogrid as the number of load cycles increases from 1,000 to 10,000. For the Springville material, the resilient modulus increases by 2 percent for the specimens with geogrid and increases by 3 percent for the specimens without geogrid as the number of load cycles increases from 1,000 to 10,000. As with other studies, the results do not show a consistent or significant effect of geogrid reinforcement on the resilient modulus of the tested materials. The modulus at 2 percent strain has the most potential for consistently showing improvements to aggregate base materials due to both cyclic loading and geogrid reinforcement. For the Wells Draw and Springville materials, the modulus at 2 percent strain increases by 31 and 9 percent, respectively, as the number of load cycles increases from 10 to 10,000. Additionally, for the Wells Draw and Springville materials, the modulus at 2 percent strain of the specimens with geogrid is 23 and 46 percent, respectively, greater than that of the specimens without geogrid. The results show a consistent and significant positive effect of geogrid reinforcement on modulus at 2 percent strain of the tested materials. According to the modulus at 2 percent strain results, a sufficient conditioning period appears to occur at 5,000 cycles for the Wells Draw material and 10,000 cycles for the Springville material.

When a clay soil is sheared, clay particles along the shear plane become aligned in the direction of shear, forming "slickensided" surfaces. Slickensided surfaces are often observed along the sliding plane in field landslides. Because the clay particles along a slickensided surface are already aligned in the direction of shear, the available shear resistance is significantly less than that of the surrounding soil. During an earthquake, ground shaking often causes landslide movement. For existing landslides or repaired landslides that contain slickensided rupture surfaces, it is reasonable to expect that the movement will occur along the existing slickensided surfaces, because they are weaker than the surrounding soil. The amount of movement that occurs is controlled by the dynamic resistance that can be mobilized along the slickensided surfaces. The objective of this study was to investigate, through laboratory strength tests and centrifuge model tests, the shearing resistance that can be mobilized on slickensided rupture surfaces in clay slopes during earthquakes. A method was developed for preparing slickensided rupture surfaces in the laboratory, and a series of ring shear tests, direct shear tests, and triaxial tests was conducted to study the static and cyclic shear resistance of slickensided surfaces. Two dynamic centrifuge tests were also performed to study the dynamic shear behavior of slickensided clay slopes. Newmark's method was used to back-calculate cyclic strengths from the centrifuge data. Test results show that the cyclic shear resistance that can be mobilized along slickensided surfaces is higher than the drained shear resistance that is applicable for static loading conditions. These results, coupled with a review of existing literature, provide justification for using cyclic strengths that are at least 20% larger than the drained residual shear strength for analyses of seismic stability of slickensided clay slopes. This represents a departure from the current state of practice, which is to use the drained residual shear strength as a "first-order approximation of the residual strength friction angle under undrained and rapid loading conditions" (Blake et al., 2002). / Ph. D.

Traditional mortise and tenon timber frames have been used in modern construction for a substantial period of time with acceptable performance against weather phenomena and other hazards. However, performance criteria for this style of timber framing are not well defined in current codes and standards. To determine performance criteria for free-standing timber frames with knee-braces, three tasks were undertaken: (1) Two timber frame specimens were tested under cyclic loads to determine hysteretic behavior, damage states, and to explore rehabilitation of a damaged member using self-tapping screws. Three damage states for were identified: peg shear, tenon tearout, and post or beam splitting. Self-tapping screws were able to restore the strength of the 2-peg timber frame with the damaged beam, but not the stiffness of the frame. (2) Four timber frame mortise and tenon connection specimens were subjected to damp conditions for six months and then tested under monotonic tensile load to determine the effect of joint details. The results indicated that connection types tested had similar strength and stiffness. (3) Twelve free-standing timber frames with knee braces located at various sites across the United States were tested in the field under impulse loading to determine the fundamental period of vibration and to estimate damping. A relationship between the fundamental period and the mean roof height was fit to the test data using a power-law equation, and three sets of parameters were determined: a lower-bound equation for seismic loads, an upper-bound equation for wind loads, and mean equation for human-induced vibration performance criteria.

Reinforced Concrete (RC) structures are common in earthquake-prone areas. During an earthquake, the steel reinforcement is subjected to cyclic strain histories which lead to inelastic response. In the case of rare, strong earthquakes, inelastic buckling and even rupture due to low-cycle fatigue can also occur. The understanding and characterization of the performance of RC structures under earthquake hazards requires the accurate simulation of the inelastic hysteretic behavior of steel reinforcement by means of appropriate constitutive models. Several uniaxial material models have been developed for reinforcing steel. Existing material models sacrifice efficiency for accuracy or vice versa. Conceptually simple and numerically efficient models do not accurately capture the hysteretic response and ignore rupture or buckling. On the other hand, more refined material models are characterized by iterative stress update procedures which can significantly increase the computational cost of an analysis. Additionally, experience suggests that refined models attempting for the effect of inelastic buckling tend to lead to numerical convergence problems in the stress update procedure. The goal of the present study is the formulation and implementation of an accurate and computationally efficient constitutive model for steel reinforcement under cyclic loading. A previously developed model, capable of capturing the inelastic hysteretic response of reinforcing steel in the absence of buckling and rupture, is used as a starting point in this study. The model is enhanced by replacing its original, iterative stress update procedure with an equally accurate, non-iterative one. Additionally, the model is enhanced to capture the effects of inelastic buckling and of rupture. The accuracy of the model and the efficiency of the non-iterative stress update algorithm are demonstrated by means of validation analyses. / Master of Science

The racking performance of light-frame shear walls subjected to monotonic and cyclic loading is the focus of this thesis. The sheathing materials investigated are oriented strandboard (OSB), hardboard, fiberboard, and gypsum wallboard. The objectives of this study were to (1) obtain and compare performance characteristics of each sheathing material; (2) compare the effects of monotonic loading versus the cyclic loading response; (3) investigate the contribution of gypsum in walls with dissimilar sheathing materials on opposite sides of the wall; and (4) study the effects of using overturning anchors. The monotonic tests, which incorporated the use of hold-downs, were performed according to ASTM E564. Half of the cyclic tests were performed with hold-downs, and half were performed without hold-downs. The cyclic tests were performed according to the recently adopted cyclic testing procedure ASTM E2126. A total of forty-five walls were tested with various configurations. The size of the walls was 1.2 x 2.4m (4 x 8ft). Two tests were performed with each sheathing material subjected to each type of loading: monotonic, cyclic with hold-downs, and cyclic without hold-downs. Two tests were then performed with OSB, hardboard, or fiberboard on one side of the wall and gypsum on the other side of the wall to study the effects of using dissimilar sheathing materials on the shear walls. The OSB and hardboard exhibited similar performance, and were the strongest of the four sheathing materials. Fiberboard performed better than gypsum, but worse than OSB and hardboard. In general, the performance indicators decreased when the walls were subjected to cyclic loading. The contribution of gypsum to walls with hold-downs was significant, but was not linearly additive. The use of hold-downs had a large effect on the performance of the walls. All shear wall performance indicators decreased when hold-downs were not included, with an average reduction of 66% in the peak load. / Master of Science

In this investigation, thirty-six shear walls measuring 8 feet (2.4 m) in width and possessing heights of 8, 9 and 10 feet (2.4, 2.7 and 3.0 m) were subjected to the reversed, cyclic loading schedule of the standard CUREE protocol in order to determine the performance capabilities of shear walls greater than 8 feet (2.4 m) in height sheathed with long panels. Of the thirty-six walls, a total of twelve walls measuring 9 and 10 feet (2.7 and 3.0 m) in height were sheathed with 4 x 8 feet (1.2 x 2.4 m) panels which required additional blocking members between the studs of the frame. Values obtained from the tests performed on these walls provided a direct comparison to those obtained from the walls of equal height, but sheathed with a long panel capable of spanning the entire height of the wall. The capabilities of long panels were investigated when used as the sheathing elements of shear walls with and without a mechanical hold-down device attached to the base of the end stud. An advantage of the long panel was investigated in which it was extended past the bottom plate and down onto the band joist to determine if significant resistance to the uplift present in walls without mechanical hold-down devices could be provided. Also, the effects of orienting the fibers of a 4 x 9 feet (1.2 x 2.7 m) panel in the alternate direction were examined. Average values of the parameters produced by walls sheathed with long panels either matched or exceeded those of its counterpart sheathed with 4 x 8 feet (1.2 x 2.4 m) panels in all configurations except the 10 feet (3.0 m) tall wall without hold-down devices. In fact, 4 x 9 feet (1.2 x 2.7 m) panels increased the performance of 9 feet (2.7 m) tall walls equipped with hold-down restraint significantly. Extending the long panels past the bottom plate and down onto the band joist improved the performance of both 8 and 9 feet (2.4 and 2.7 m) tall prescriptive shear walls significantly. Walls sheathed with panels made of fibers oriented in the alternate direction performed identically to those sheathed with panels of typical fiber orientation until the point of peak load. Once peak load was reached, walls sheathed with panels of alternate oriented fibers failed in a more sudden and brittle manner. / Master of Science

This thesis presents the results of testing to determine the significance of the group action factor at the 5% offset yield and capacity of single-shear bolted wood connections loaded parallel to grain. The single and multiple-bolt connections tested represent common connection geometries used in wood construction in the United States. The results of both monotonic and cyclic loading of connections are presented. Monotonic test data was used to determine an appropriately scaled CUREE Displacement Controlled Quasi-Static Cyclic Protocol. Overall, one hundred and eighty connections were tested using this cyclic protocol based on data obtained from thirty-three monotonic tests. Tested assemblies had geometric variables that include number of bolts per row, number of rows, bolt diameter, and side member material. In addition, the main and side member material and thickness were designed to produce three of the four major connection yield modes as defined by the 1997 National Design Specification for Wood Construction (AF&PA, 1997). Results from this research address the need for adequate spacing of bolts in a row to control the brittle connection behavior that directly affected the group action factor at capacity. / Master of Science

Much previous experimentation related to wood structures has employed monotonic loading to replicate static situations. However, instances of natural hazards have raised interest in the response of structural connections to dynamic loads. This increased interest led the Consortium of Universities for Research in Earthquake Engineering (CUREE) to develop a testing protocol for reverse-cyclic loading, which involves cycling loads through zero in order to test specimens in both tension and compression. With the CUREE testing protocol in place, recent research has been devoted to understanding the effects of reverse-cyclic loading on multiple-fastener connections. Experimentation by Heine (2001), Anderson (2002), Billings (2004) and others contributed to a better understanding of bolted connection behavior under reverse-cyclic loading. However, some questions remained. Billings was unable to consistently produce yield modes III and IV, meaning that her suggested bolt spacing of seven times the bolt diameter (7D) could not be applied to connections subject to these yield modes without further testing. In addition, the work of Anderson and Billings raised questions regarding the proper measurement of bending yield strength in bolts and the relationship between the bending yield strength and the tensile yield strength. These topics are each addressed by this project and thesis report. Results of the connection testing presented in this report can be used in conjunction with the work of Anderson and Billings to critically evaluate the 4D between-bolt spacing recommended by the National Design Specification (NDS) for Wood Construction (AF&PA, 2001). Results of the bolt testing provide a supplement to the search for a reliable method for the measurement of bending yield strength in bolts. / Master of Science

An experimental investigation was conducted to study the extended end-plate moment connections subjected to cyclic loading. Seven specimens representing three end-plate moment connection configurations commonly used in the pre-engineered building industry were used. The connections were designed using yield-line theory to predict end-plate yielding and the modified Kennedy method to predict maximum bolt force calculations including prying action. A displacement controlled loading history was used to load the specimens. The maximum moments obtained experimentally and the experimental bolt forces throughout loading were compared with analytical predictions and finite element model results. The inelastic rotation of connections was calculated and conclusions were drawn on the compliance of these connections with current AISC specifications. / Master of Science

The first part of the thesis addresses the fatigue performance of concrete bridge decks with GFRP stay-in-place structural forms replacing the bottom layer of rebar. The forms were either flat plate with T-up ribs joined using lap splices, or corrugated forms joined through pin-and-eye connections. The decks were supported by simulated Type III precast AASHTO girders spaced at 1775mm (6ft.). Two surface preparations were examined for each GFRP form, either using adhesive coating that bonds to freshly cast concrete, or simply cleaning the surface before casting. For the bonded deck with flat-ribbed forms, adhesive bond and mechanical fasteners were used at the lap splice, whereas the lap splice of the unbonded deck had no adhesive or fasteners. All the decks survived 3M cycles at 123kN service load of CL625 CHBDC design truck. The bonded flat-ribbed-form deck survived an additional 2M cycles at a higher load simulating a larger girder spacing of 8ft. Stiffness degradations were 9-33% with more reduction in the unbonded specimens. Nonetheless, live load deflections of all specimens remained below span/1600. The residual ultimate strengths after fatigue were reduced by 5% and 27% for the flat-ribbed and corrugated forms, respectively, but remained 7 and 3 times higher than service load. The second part of the thesis investigates the performance of bridge deck overhangs reinforced by GFRP rebar. Overhangs of full composite slab-on-girder bridge decks at 1:2.75 scale were tested monotonically under an AASHTO tire pad. Five tests were conducted on overhangs of two lengths: 260mm and 516mm, representing scaled overhangs of 6ft. and 8ft. girder spacing, respectively. The 260mm overhang was completely reinforced with GFRP rebar while the 516mm overhang consisted of a GFRP-reinforced section and a steel-reinforced section. The peak loads were approximately 2 to 3 times the established equivalent service load of 24.3kN, even though the overhangs were not designed for flexure according to the CHBDC but rather with lighter minimum reinforcement in anticipation of shear failure. The failure mode Abstract ii of each overhang section was punching shear. The steel-reinforced overhang section exhibited a greater peak load capacity (13.5%) and greater deformability (35%) when compared to the GFRP-reinforced overhang section. / Thesis (Master, Civil Engineering) -- Queen's University, 2013-09-17 18:54:18.131