The thesis focuses on a higher order noise-shaping Δ ADC architecture which employs filtered quantization error as a dither signal. Furthermore, the work studies implementation challenges using Switched-Capacitor and Switched-Current techniques. Digitization in an IF conversion receiver can be accomplished either with a wide band Nyquist rate ADC or a BandPass Δ ADC. The use of the latter is the optimum solution since the bandwidth of the IF signals is typically much smaller than the carrier frequency and reducing the quantization noise in the entire nyquist band becomes superfluous. Instead by using BandPass Δ ADCs the quantization noise power is reduced only in a narrow band around IF location. We study state-of-the-art high dynamic range Δ data converter topologies suited for wide-band radio receivers. We propose a topology which achieves higher order noise shaping by employing filtered quantization error as a dither signal. We study implementation challenges for Δ converters in digital technology. Traditionally, Δ ADCs used Switched-Capacitor (SC) circuits to realize their building blocks. This analog sample-data technique is based on the idea that a periodically switched capacitor can emulate a resistor. The limiting factor that degrades the performance of SC circuits implemented in standard VLSI technologies is the continuous reduction of supply voltages, prompted by the continuous scaling-down process. This fact, which is advantageous for digital circuitry, makes the design of SC circuits difficult, which are forced to use clock boosting strategies for switches and to increase the power consumption in order to obtain high-speed and high dynamic range opamps with low voltage operation. In this scenario, the use of current-domain sampled data technique, also named Switched-Current (SI), instead of voltages results advantageous for several reasons. As the signal carriers are currents, the supply voltage does not limit the signal range as much as in SC circuits. Therefore, SI circuits are more suitable than SC for low-voltage operation. This work studies the feasibility and bottlenecks of implementing Δ modulator building blocks using SI technique. A BandPass filter, DAC and 1-bit quantizer have been designed in 0.18µm technology using SI technique. (For mathematical equations pl refer the pdf file)

<p>QC 20140609</p>

No description available.

Over the last decade, electronics operating at high temperatures have been increasingly demanded to support in situ sensing applications such as automotive, deep-well drilling and aerospace. However, few of these applications have requirements above 460 °C, as the surface temperature of Venus, which is a specific target for the seismic sensing application in this thesis. Due to its wide bandgap, Silicon Carbide (SiC) is a promising candidate to implement integrated circuits (ICs) operating in such extreme environments. In this thesis, various analog and mixed-signal ICs in 4H-SiC bipolar technology for high-temperature sensing applications are explored, in which the device performance variation over temperatures are considered. For this purpose, device modeling, circuit design, layout design, and device/circuit characterization are involved. In this thesis, the circuits are fabricated in two batches using similar technologies. In Batch 1, the first SiC sigma-delta modulator is demonstrated to operate up to 500 °C with a 30 dB peak SNDR. Its building blocks including a fully-differential amplifier, an integrator and a comparator are characterized individually to investigate the modulator performance variation over temperatures. In the succeeding Batch 2, a SiC electromechanical sigma-delta modulator is designed with a chosen Si capacitive sensor for seismic sensing on Venus. Its building blocks including a charge amplifier, a multiplier and an oscillator are designed. Compared to Batch 1, a smaller transistor and two metal-interconnects are used to implement higher integration ICs in Batch 2. Moreover, the first VBIC-based compact model featured with continuous-temperature scalability from 27 to 500 °C is developed based on the SiC transistor in Batch 1, in order to optimize the design of circuits in Batch 2. The demonstrated performance of ICs in Batch 1 show the feasibility to further develop the SiC readout ICs for seismic sensor system operating on Venus. / <p>QC 20170911</p>

Methodology and issues of data transformation and its information value estimation during the integration of the heterogenous information sources PhDr. Ivan BARTOŠ Abstract This study focuses mainly on the data and information transformation issue. This topic is currently critical in several scientific and commercial areas. Information value, information quality and the quality of the source data differs between the various systems. This is not only due to the different topologies of the information sources but also because of its different understanding and a manner of storing the information describing the entity of the enterprise. Such information systems, respectively database systems in the scope of the thesis, could perform well as the stand alone systems. The issue appears in the moment when such heterogeneous systems are required to be integrated and the information shall be migrated between each other. The thesis is logically divided into four major parts based on these issues. The first part describes the methods that can be used to classify the data quality of the source system (the one to be integrated) from which the information can be extracted. Based on assumption of the common lack of project and system documentation hereby introduced methods can be used for such qualification even when the...