The goal of this research is to investigate the behavior of polymer concrete confined with a carbon fiber sleeve used as a pile foundation. To evaluate the behavior of a confined polymer concrete pile in this research, four steps was considered. The first step of this investigation considered the mix design of polymer concrete, polymer concrete is a new material which is a combination of epoxy resin and aggregate. Instead of using a traditional mix of cement and water to make concrete, epoxy resin is used. Three dissimilar varieties of aggregate are mixed with different ratios in order to reach the maximum bulk density to obtain the maximum strength. After discovering the optimum ratio which gives the maximum bulk density, several samples of the aggregate are mixed with different ratios of epoxy resin. Next, the samples are investigated in a compression test to observe which ratios have the maximum strength and this ratio is used for a polymer concrete mix design to create a pile foundation. The pile is a built using a cast in place method and confined with a sleeve of carbon fiber. The second part of this investigation determined the structural mechanical properties of confined polymer concrete pile material. The unconfined and confined polymer concrete was tested in compression to determine compressive strength and stress-strain behavior. Similar tests were conducted on unconfined and confined cement concrete for comparison between these materials. Additional tension tests were conducted on unconfined polymer concrete. Then, a carbon fiber sleeve was tested in compression test to determine tensile strength and tension stress-strain behavior. After these tests, the confined polymer concrete is modeled in the computer program MATTCAD which is used to calculate the theoretical bending moment capacity and load-displacement curve. Finally, the confined polymer concrete is tested with the MTS 311 Load Frame in three point load flexure test to determine the experimentally bending moment capacity, load-displacement curve and compare with theoretical results. Confined polymer concrete was tested in one and two way cyclic loading to observe the ductility behavior of this material as laterally loaded piles and compared with cement concrete results in cyclic loading. The third part of this investigation determined the geotechnical mechanical properties of confined polymer concrete pile material. Cyclic Multi Degree of Freedom (CYMDOF) device was used to determine interface reaction and friction angle between confined polymer concrete and soil with interface shear test theory method. Furthermore, the same device was used to determine the friction angle of soil with direct shear test theory, and compare the friction angle results together. The last part of this investigation considered the behavior of different sized confined polymer concrete pile in different types of soil. A confined polymer concrete pile was modeled into PLAXIS and OPENSEES PL computer software to analysis pile in axial load and lateral load respectively. Furthermore, a cement concrete pile was modeled with similar software and conditions to compare these two materials.

No description available.

During shearing of stiff clays, plate-shaped clay particles are parallel-oriented in the direction of shear reaching the minimum resistance of &ldquo / residual shear strength&rdquo / . The residual shear strength envelopes of stiff clays are curved, but for practical purposes represented by linear envelopes. This study investigates the nonlinearity of the residual shear strength envelope using experimental evidence (i) from laboratory reversal direct shear tests on two stiff clays (Ankara clay and kaolinite) at 25 to 900 kPa effective normal stresses and (ii) from laboratory data collected from literature. To evaluate the importance of nonlinearity of the envelope for geotechnical engineering practice, by limit equilibrium method, (a) case histories of reactivated landslides are analyzed and (b) a parametric study is carried out. Conclusions of this study are: (1) The residual shear strength envelopes of both Ankara clay and kaolinite are nonlinear, and can be represented by a power function (cohesion is zero). (2) At least 3 reversals or cumulative 20 mm shear displacement of direct shear box is recommended to reach residual condition. (3) Empirical relations between plasticity index and residual friction angle can accurately estimate the residual strength of stiff clays. (4) Nonlinearity is especially important for landslides where average effective normal stress on the shear plane is less than 50 kPa, both for translational and rotational failures. For such slopes using a linear strength envelope overestimates the factor of safety (more significantly for the case of high pore pressures). (5) As the plasticity index increases, the power &ldquo / b&rdquo / of the nonlinear shear strength envelope decreases, indicating more significant nonlinearity. For less plastic materials, using linear and nonlinear shear strength envelopes does not affect the factor of safety.

Vibration compaction is the most effective way of compacting coarse-grained materials. The effects of vibration frequency and amplitude on the compaction density of different backfill materials (No. 4 natural sand, No. 24 stone sand and No. 5, No. 8, No. 43 aggregates), were studied in this research. The test materials were characterized based on the particle sizes and morphology parameters using digital image analysis technique. Small-scale laboratory compaction tests were carried out with variable frequency and amplitude of vibrations using vibratory hammer and vibratory table. The results show an increase in density with the increase in amplitude and frequency of vibration. However, the increase in density with the increase in amplitude of vibration is more pronounced for the coarse aggregates than for the sands. A comparison of the maximum dry densities of different test materials shows that the dry densities obtained after compaction using the vibratory hammer are greater than those obtained after compaction using the vibratory table at the highest amplitude and frequency of vibration available in both equipment. Large-scale vibratory roller compaction tests were performed in the field for No. 30 backfill soil to observe the effect of vibration frequency and number of passes on the compaction density. Accelerometer sensors were attached to the roller drum (Caterpillar, model CS56B) to measure the frequency of vibration for the two different vibration settings available to the roller. For this roller and soil tested, the results show that the higher vibration setting is more effective. Direct shear tests and direct interface shear tests were performed to study the impact of particle characteristics of the coarse-grained backfill materials on interface shear resistance. A unique relationship was found between the normalized surface roughness and the ratio of critical-state interface friction angle between sand-gravel mixture with steel to the internal critical-state friction angle of the sand-gravel mixture.

Reservoir release patterns are determined by a number of purposes, the most fundamental of which is to manage water resources for human use. Managing our water resources means not only controlling the water in reservoirs but also determining the optimum release rate taking into account factors such as reservoir stability, power generation, water supply for domestic, industrial, and agricultural uses, and the river ecosystem. However, riverbank stability has generally not been considered as a factor, even though release rates may have a significant effect on downstream riverbank stability. Riverbank retreat not only impacts land properties but also damages structures along the river such as roads, bridges and even buildings. Thus, reservoir releases need to also take into account the downstream riverbank stability and erosion issues. The study presented here investigates the riverbank stability and erosion at five study sites representing straight as well as inside and outside channel meander bends located on the lower Roanoke River near Scotland Neck, North Carolina. Extensive laboratory and field experiments were performed to define the hydraulic and geotechnical properties of the riverbank soils at each site. Specifically, soil water characteristic curves were determined using six different techniques and the results compared to existing mathematical models. Hydraulic conductivity was estimated using both laboratory and in situ tests. Due to the wide range of experimentally obtained values, the values determined by each of the methods was used for transient seepage modeling and the modeling results compared to the actual ground water table measured in the field. The results indicate that although the hydraulic conductivities determined by in situ tests were much larger than those typically reported for the soils by lab tests, numerical predictions of the ground water table using the in situ values provided a good fit for the measured ground water table elevation. Shear strengths of unsaturated soils were determined using multistage suction controlled direct shear tests. The test method was validated, and saturated and unsaturated shear strength parameters determined. These parameters, which were determined on the basis of results from both laboratory and field measurements, and the associated boundary conditions, which took into account representative flow rates and patterns including peaking, drawdown and step-down scenarios, were then utilized for transient seepage analyses and slope stability analyses performed using SLIDE, a software package developed by Rocscience. The analyses confirmed that the riverbanks are stable for all flow conditions, although the presence of lower permeability soils in some areas may create excess pore water pressures, especially during drawdown and step-down events, that result in the slope becoming unstable in those locations. These findings indicate that overall, the current reservoir release patterns do not cause adverse impacts on the downstream riverbanks, although a gradual drawdown after a prolonged high flow event during the wet season would reduce unfavorable conditions that threaten riverbank stability. / Ph. D.

Esta tese apresenta os princípios e a formulação de um modelo não-linear de atrito estático em interface de concreto areia. A hipótese básica para desenvolvimento das equações consiste na ocorrência do atrito de deslizamento (atrito verdadeiro), do atrito de rolamento (rearranjo das partículas) e da dilatância (variação de volume durante o cisalhamento). A solução analítica do modelo considera o efeito da rugosidade da superfície de contato, da curva granulométrica da areia e do seu estado de compacidade inicial. Foram realizados ensaios de cisalhamento direto com carga normal constante em interface de contato entre concreto e areia com seção de 500 mm x 500 mm com o objetivo de permitir a calibração do modelo proposto. É discutida e sugerida a incorporação da equação constitutiva desse modelo em análises de interação solo-estrutura via método dos elementos finitos. Sua aplicabilidade é demonstrada através da análise 1D e 2D de estacas de atrito executadas em areia e submetidas a carregamentos de compressão / This thesis presents the principles and formulation underlying a concrete-sand interface nonlinear static friction model. The basic hypothesis employed in the development of the model equation takes into account the interface sliding friction (true friction), a rolling friction (particle rearrangement) and dilatancy(volume variation during shear). The model analytical solution considers the effect of roughness of the contact surface, the grain size distribution and its initial state of compactness of the sand. To calibrate the proposed model, a direct shear stress test under constant load was carried out along a 500mm x 500mm section concrete-sand interface. Furthermore, a discussion and suggestion of the inclusion of the model constitutive equation applied to the analysis of soil-structure interaction using the finite element method are presented. The applicability of the proposed model is proven through the analysis of 1-D and 2-D skin friction piles made of sand mass subjected to compression load

Closely jointed greywacke rock masses are widespread throughout both the North and South Islands of New Zealand and much of New Zealand's infrastructure is constructed upon greywacke rock masses. This thesis deals with determining the rock mass strength of unweathered closely jointed New Zealand greywacke rock masses. Currently, the estimation of rock mass strength and deformability is reasonably well predicted through the use of such empirical failure criteria as the Hoek-Brown failure criterion and empirical expressions to predict deformability. However, previous studies upon predicting the strength and deformability of unweathered closely jointed New Zealand greywacke rock masses has shown that existing empirical methods of determining strength and deformability are unsatisfactory. The problem with predicting rock mass strength and deformability moduli of New Zealand greywacke and the lack of adequate data to calibrate a failure criterion was the starting point for this work. The objective of this thesis was to increase the knowledge of intact and defect properties of closely jointed greywacke, develop reliable rock mass data with which to calibrate a failure criterion and improve the ability to estimate the rock mass strength of greywacke rock masses. A review of existing failure criteria for rock masses was conducted and of these criteria, the Hoek-Brown rock mass failure criteria was selected to calibrate to both the intact rock and rock mass failure data, because of its broad acceptance in the rock mechanics community. A database of greywacke properties was developed based on previous studies upon unweathered greywacke around New Zealand and is attached to the thesis as an Appendix. The database included descriptions of greywacke defect properties and mechanical properties of the intact rock and joints. From this database, inputs could be justified for numerical modelling and later analyses of failure criteria. Records from the construction archives of the Benmore and Aviemore hydroelectric power projects in the South Island of New Zealand were reviewed to obtain information and results from a series of shear tests carried out on unweathered closely jointed greywacke in the 1960s. Data on rock mass strength at failure and rock mass deformability were extracted from these records to assess the predictability of the failure criterion and deformability expressions. Problems experienced during the shear tests at the Aviemore dam site created doubt as to the actual rock mass strengths achieved at failure. The behaviour of these tests was studied using the finite difference code FLAC. The work was aimed at investigating the potential for transfer of shear force between the two concrete blocks sheared in each test and the impact shear force transfer had upon the likely normal stresses beneath each block at failure. The numerical modelling results indicated that a combination of preferential failure occurring in one direction, and doubt in the actual normal load applied to the concrete blocks during testing lead to premature failure in the blocks sheared upstream. The blocks sheared in the opposite direction failed at normal stresses that are reflective of the strength of an unweathered greywacke rock mass, but these results could be explained by failure occurring along defects therefore not satisfying the assumptions of homogeneity typically required of a rock mass failure criterion. The Hoek-Brown failure criterion for intact rock was investigated by fitting it to the largest intact greywacke datasets. For a full set of test data (i.e. including tensile data), the Mostyn & Douglas (2000) variant of the Hoek-Brown failure criterion gave the best fit for a full set of rock mass data. A multiple regression method was developed which improved the fitted curve to intact data in the tensile region and gave the best estimate of tensile strength if no existing lab results for tensile strength were available. These results suggest that the Hoek-Brown failure criterion is significantly limited in its applicability to intact NZ greywacke rock. Hoek-Brown input parameters different to those suggested by Hoek et al (2002) are recommended for using the Hoek-Brown failure criterion for intact NZ greywacke. For closely jointed NZ greywacke rock masses, the results from the shear tests at Aviemore and Benmore were separated into different GSI classes and Hoek-Brown envelopes fitted to the datasets by multiple regression. Revised expressions were proposed for each Hoek-Brown input parameter (mb, s, ab) as a function of the GSI. The resulting revised Hoek-Brown failure envelopes for NZ greywacke offer a significant improvement on the existing criterion used to predict the strength of NZ greywacke intact rock and rock masses. The differences in the behaviour of the reaction blocks that failed before the test blocks and the reduction in rock strength due to sliding along defects from that predicted could be reasoned from recorded observations and the behaviour of the concrete blocks during the shear tests. This study has clearly illustrated the need for continued research in this area. This includes (1) a means of assessing the role of defects upon the shear strength of closely jointed greywacke rock mass into a failure criterion, (2) further modelling of the in-situ shear tests by a discrete element procedure to expressly determine the role of the defect on failure, (3) more testing on rock masses to obtain more data to calibrate a rock mass failure criterion, and (4) more studies on predicting the strength of extremely disturbed rock masses.

Esta tese apresenta os princípios e a formulação de um modelo não-linear de atrito estático em interface de concreto areia. A hipótese básica para desenvolvimento das equações consiste na ocorrência do atrito de deslizamento (atrito verdadeiro), do atrito de rolamento (rearranjo das partículas) e da dilatância (variação de volume durante o cisalhamento). A solução analítica do modelo considera o efeito da rugosidade da superfície de contato, da curva granulométrica da areia e do seu estado de compacidade inicial. Foram realizados ensaios de cisalhamento direto com carga normal constante em interface de contato entre concreto e areia com seção de 500 mm x 500 mm com o objetivo de permitir a calibração do modelo proposto. É discutida e sugerida a incorporação da equação constitutiva desse modelo em análises de interação solo-estrutura via método dos elementos finitos. Sua aplicabilidade é demonstrada através da análise 1D e 2D de estacas de atrito executadas em areia e submetidas a carregamentos de compressão / This thesis presents the principles and formulation underlying a concrete-sand interface nonlinear static friction model. The basic hypothesis employed in the development of the model equation takes into account the interface sliding friction (true friction), a rolling friction (particle rearrangement) and dilatancy(volume variation during shear). The model analytical solution considers the effect of roughness of the contact surface, the grain size distribution and its initial state of compactness of the sand. To calibrate the proposed model, a direct shear stress test under constant load was carried out along a 500mm x 500mm section concrete-sand interface. Furthermore, a discussion and suggestion of the inclusion of the model constitutive equation applied to the analysis of soil-structure interaction using the finite element method are presented. The applicability of the proposed model is proven through the analysis of 1-D and 2-D skin friction piles made of sand mass subjected to compression load

The Discrete element method (DEM) is a methodology to investigatethe interactions among granular materials. It analyzes the behavior of par-ticulate environments by solving force-displacement equations that adhereto Newton’s second law of motion. Despite its usefulness, the DEM is notwithout limitations, and researchers are still facing certain challenges thatrestrict them from performing detailed analyses of granular materials. Thisstudy addresses two issues in DEM modeling of granular materials in rail-way embankments. Firstly, the long computational time required by theDEM for modeling fine angular particles in granular materials is addressedby exploring the effects of particle scaling on the shear behavior of granularmaterial. This study investigates the impact of particle size distribution,particle angularity, and the amount of scaling on the accuracy and compu-tational efficiency of DEM. Secondly, the limitations of DEM in includingthe continuous rail beam structure in the track are addressed by verifyinga DEM model against physical measurements of a full-scale ballasted trackand investigating the influence of including the rail beam structure on high-speed railway ballasted tracks. The results show that the use of particlescaling in the first study significantly improves the computational efficiencyof the DEM while maintaining accuracy, and this method is used in thesecond study to investigate the influence of the rail beam structure on thebehavior of railway tracks. / Diskreta elementmetoden (DEM) är en effektiv metod för att undersö-ka interaktioner i granulära material. Metoden analyserar samverkan mellanpartiklar genom att lösa kraft-deformationsekvationer som följer Newtonsandra lag. Trots dess användbarhet har DEM vissa begränsningar och fors-kare stöter fortfarande på vissa utmaningar som hindrar dem från att ge-nomföra detaljerade analyser av granulära material. Denna studie tar upptvå frågeställningar vid DEM-modellering av granulära material i järnvägs-bankar. För det första behandlas den långa beräkningstiden som krävs föratt modellera granulära material genom att utforska effekterna av parti-kelskalning på skjuvbeteendet. Studien undersöker effekten av partikelstor-leksfördelning och spetsighet på noggrannheten och beräkningseffektivite-ten. För det andra behandlas begränsningarna hos DEM när det gäller attinkludera den kontinuerliga rälsstrukturen i spåret genom att verifiera enDEM-modell mot fysiska mätningar av ett ballasterat spår i full skala ochundersöka inverkan av att inkludera rälsstrukturen. Resultaten i den förstastudien visar att tillämpningen av partikelskalning avsevärt förbättrar be-räkningseffektiviteten samtidigt som noggrannheten bibehålls. Partikelskal-ning används i den andra studien för att undersöka inverkan av rälsstruk-turen på beteendet hos järnvägsspår. / <p>QC 230508</p>

No description available.