Laminar flow control has been studied for several decades in an effort to achieve higher efficiencies for aircraft. Successful implementation of laminar flow control technology on transport aircraft could significantly reduce drag and increase operating efficiency and range. However, the crossflow instability present on swept-wing boundary layers has been a chief hurdle in the design of laminar wings. The use of spanwise-periodic discrete roughness elements (DREs) applied near the leading edge of a swept-wing typical of a transport aircraft represents a promising technique able to control crossflow and delay transition to accomplish the goal of increased laminar flow. Recently, the Flight Research Laboratory at Texas A&M University conducted an extensive flight test study using DREs on a swept-wing model at chord Reynolds numbers in the range of eight million. The results of this study indicated DREs were able to double the laminar flow on the model, pushing transition back to 60 percent chord. With the successful demonstration of DRE technology at these lower chord Reynolds numbers, the next logical step is to extend the technology to higher Reynolds numbers in the range of 15 to 20 million typical of smaller transport aircraft. To conduct the flight tests at the higher Reynolds numbers, DREs will be placed on a wing glove attached to the aircraft wing. However, a feasibility study was necessary before initiating the flight-testing. First, a suitable aircraft able to achieve the Reynolds numbers and accommodate a wing glove was identified. Next, a full CFD analysis of the aircraft was performed to determine any adverse effects on the wing flow-field from the aircraft engines. This required an accurate CAD model of the selected aircraft. Proper modeling techniques were needed to represent the effects of the aircraft engine. Once sufficient CFD results were obtained, they were used as guidance for the placement of the glove. The attainable chord Reynolds numbers based on the recommendations for the wing glove placement then determined if the selected aircraft was suitable for the flight-testing.

Engineers of off-road equipment, on-road vehicles, pavement, and tires must assess the roughness of a terrain surface for the design of their products. The International Roughness Index (IRI), a standardized means of assessing longitudinal road roughness, quantifies roughness based on the average suspension travel for a particular vehicle at a prescribed speed. The Discrete Roughness Index (DRI) developed in this work address fundamental limitations of the IRI. Specifically, the DRI is calculated for each discretely measured location along a terrain surface and is applicable to vehicles traveling at varying speeds and using parameters other than the Golden Quarter-Car on which the IRI is based. The development of the DRI begins with a consistent discretization of the terrain surface, vehicle response, and the IRI. Next the Fractional Response Coefficient is developed, the properties of which are critical in the development of the DRI. The DRI is developed and its properties are discussed through theory and simulation of the ASTM E1926-08 profile. One important property of the average DRI is that it converges to the IRI as the distance between sampled points becomes smaller, for the particular case when the Golden Quarter-Car model is simulated at 80 kph. The DRI is not an alternative to the standard IRI, therefore, but a widely applicable roughness measure of which the standard IRI is a single specialized application. / Master of Science

The aerodynamic benefits of laminar flow have long made it a sought-after attribute in aircraft design. By laminarizing portions of an aircraft, such as the wing or empennage, significant reductions in drag could be achieved, reducing fuel burn rate and increasing range. In addition to environmental benefits, the economic implications of improved fuel efficiency could be substantial due to the upward trend of fuel prices. This is especially true for the commercial aviation industry, where fuel usage is high and fuel expense as a percent of total operating cost is high. Transition from laminar to turbulent flow can be caused by several different transition mechanisms, but the crossflow instability present in swept-wing boundary layers remains the primary obstacle to overcome. One promising technique that could be used to control the crossflow instability is the use of spanwise-periodic discrete roughness elements (DREs). The Flight Research Laboratory (FRL) at Texas A&M University has already shown that an array of DREs can successfully delay transition beyond its natural location in flight at chord Reynolds numbers of 8.0x10^6. The next step is to apply DRE technology at Reynolds numbers between 20x10^6 and 30x10^6, characteristic of transport aircraft. NASA's Environmentally Responsible Aviation Project has sponsored a transonic laminar-flow wing glove experiment further exploring the capabilities of DRE technology. The experiment will be carried out jointly by FRL, the NASA Langley Research Center, and the NASA Dryden Flight Research Center. Upon completion of a wing glove design, a thorough computational evaluation was necessary to determine if the design can meet the experimental requirements. First, representative CAD models of the testbed aircraft and wing glove were created. Next, a computational grid was generated employing these CAD models. Following this step, full-aircraft CFD flowfield calculations were completed at a variety of flight conditions. Finally, these flowfield data were used to perform boundary-layer stability calculations for the wing glove. Based on the results generated by flowfield and stability calculations, conclusions and recommendations regarding design effectiveness were made, providing guidance for the experiment as it moved beyond the design phase.

Boundary-layer transition from a laminar to a turbulent regime is a critical driver in the design of high-speed vehicles. The aerothermodynamic loads associated with transitional or fully turbulent hypersonic boundary layers are several times higher than those associated with laminar flow. The presence of isolated roughness elements on the surface of a body can accelerate the growth of incoming disturbances and introduce additional instability mechanisms in the flow field, eventually leading to a premature occurrence of transition. This dissertation studies the instabilities induced by three-dimensional discrete roughness elements located inside a high-speed boundary layer developing on a flat plate. Two-dimensional local linear stability theory (2D-LST) is employed to identify the instabilities evolving in the three-dimensional flow field that characterizes the wake induced by the roughness elements and to investigate their evolution downstream. A formulation of the disturbance energy evolution equation available for base flows depending on a single spatial direction is generalized for the first time to base flows featuring two inhomogeneous directions and perturbations depending on three spatial directions. This generalization allows to obtain a decomposition of the temporal growth rate of 2D-LST instabilities into the different contributions that lead to the production and dissipation of the total disturbance energy. This novel extension of the formulation provides an additional layer of information for understanding the energy exchange mechanisms between a three-dimensional base flow and the perturbations resulting from 2D-LST. Stability computations for a calorically perfect gas illustrate that the wake induced by the roughness elements supports the growth of different sinuous and varicose instabilities which coexist together with the Mack-mode perturbations that evolve in the flat-plate boundary layer, and which become modulated by the roughness-element wake. A single pair of sinuous and varicose disturbances is found to dominate the wake instability in the vicinity of the obstacles. The application of the newly developed decomposition of the temporal growth rate reveals that the roughness-induced wake modes extract most of their potential energy from the transport of entropy fluctuations across the base-flow temperature gradients and most of their kinetic energy from the work of the disturbance Reynolds stresses against the base-flow velocity gradients. Further downstream, the growth rate of the wake instabilities is found to be influenced by the presence of Mack-mode disturbances developing on the flat plate. Strong evidence is observed of a continuous synchronization mechanism between the wake instabilities and the Mack-mode perturbations. This phenomenon leads to an enhancement of the amplification rate of the wake modes far downstream of the roughness element, ultimately increasing the associated integrated amplification factors for some of the investigated conditions. The effects of vibrational molecular excitation and chemical non-equilibrium on the instabilities induced by a roughness element are studied for the case of a high-temperature boundary layer developing on a sharp wedge configuration. For this purpose, a 2D-LST solver for chemical non-equilibrium flows is developed for the first time, featuring a fully consistent implementation of the thermal and transport models employed for the base flow and the perturbation fields. This is achieved thanks to the automatic derivation and implementation tool (ADIT) available within the von Karman Institute extensible stability and transition analysis (VESTA) tool-kit, which enables an automatic derivation and implementation of the 2D-LST governing equations for different thermodynamic flow assumptions and models. The stability computations for this configuration show that sinuous and varicose disturbances also dominate the wake instability in the presence of vibrational molecular energy mode excitation and chemical reactions. The resulting base-flow cooling associated with the modeling of such high-temperature phenomena is found to have opposite stabilizing and destabilizing effects on the streamwise evolution of the sinuous and varicose instabilities. The modeling of vibrational excitation and chemical non-equilibrium acting exclusively on the perturbations is found to have a stabilizing influence in all cases. / Doctorat en Sciences de l'ingénieur et technologie / info:eu-repo/semantics/nonPublished