Distributed Feedback (DFB) lasers and integrated laser arrays are of great importance in Wavelength-Division Multiplexing (WDM) systems in fiber optic communication systems. High-performance, low-cost DFB lasers and laser arrays are highly desirable for applications in intra-datacenter transport and in local access networks. This dissertation is focused on the design, fabrication and achievement of high-performance, low-cost DFB Lasers and Integrated DFB Arrays for WDM Systems. It investigates the use of a novel sampled grating approach, called the equivalent phase shift method, to achieve integrated DFB laser arrays with single-mode lasing at uniformly-spaced and precisely-positioned wavelengths. First, laterally-Coupled DFB (LC-DFB) lasers with first-order sidewall gratings are realized, with gratings fabricated by optical interference lithography instead of e-beam. Then, LC-DFB lasers and LC-DFB laser arrays with sampled gratings and equivalent phase shifts are proposed, numerically analyzed and experimentally demonstrated. Each LC-DFB laser with an equivalent quarter-wave phase shift is shown to lase at the pre-specified wavelength in a single longitudinal mode, with good side-mode suppression ratio (SMSR) over a very wide range of injection currents. Integrated LC-DFB laser arrays with five uniformly-spaced wavelength channels are demonstrated, in close agreement with the design. For better performance, buried heterostructure (BH)-DFB laser and laser arrays are also demonstrated using the same sampled-grating technology. A 6-wavelenth laser array with a 300 μm cavity length and a 8-wavelength laser array with 250 μm cavity length are successively demonstrated, each showing precisely positioned lasing wavelengths, good SMSR, and uniformly good lasing characteristics under a wide range of operating currents and temperatures. Finally, it is demonstrated that the wavelength of a monolithic WDM laser array can be continuously tuned over a very wide wavelength range of nearly 40 nm. The proposed method offers a practical and cost-effective solution for the manufacture of high-performance, monolithic multi-wavelength DFB laser arrays as well as widely wavelength-tunable DFB lasers for integrated WDM systems.

Semiconductor corrugated ridge waveguide (CRW) distributed feedback (DFB) lasers offer compelling advantages over standard DFB lasers. Indeed, the use of surface gratings etched on the ridge waveguide sidewalls in CRW-DFB devices avoids any epitaxial overgrowth. This provides a considerable simplification in the fabrication process, reducing cost and time of manufacturing, and ultimately increasing yield. It offers also the potential for monolithic integration with other devices, paving the way towards low-cost and mass-production of photonics integrated circuits. In recent years, the re-consideration of growth-free DFB lasers has drawn considerable attention, particularly with the current state-of-the-art photolithography machines. In this work, we present an experimental investigation on two generations of InGaAsP/InP multiple-quantum-well (MQW) CRW-DFB lasers that have been fabricated using stepper lithography. An early developed 1310 nm CRW-DFB laser showed stable single mode with high side-mode suppression ratios (SMSR) (>50 dB), albeit with thresholds higher than anticipated. A subsequent single-mode 1550 nm CRW-DFB laser showed stable operation with SMSR (>50 dB) and narrow spectral linewidths (≤250 kHz), observed for a wide range of current injection. Besides, novel multi-electrode CRW-DFB lasers have been tested. The experimental investigation showed that narrower linewidth (<150 kHz) and wide wavelength tunability (>3 nm) have been recorded using different multi-electrode current injection configurations. The application of a time-domain modeling approach for semiconductor CRW-DFB lasers is then described for the first time. We numerically studied the effect of the radiation modes on CRW-DFB laser properties by using time-domain coupled wave equations. High-order corrugated gratings with λ/4 phase-shit were analyzed, where the degree of longitudinal spatial hole burning (LSHB) can be effectively reduced by means of fine tuning of the grating duty cycle. Additionally, we showed how the side-mode suppression ratio can be predicted depending on the device geometry.

Le déploiement des réseaux optiques d'accés et métropolitains à crée un besoin incessant de débits élevés et de portées étendues. Une demande pour des sources optiques compactes, polyvalentes, de bas coût et de consommation réduite a vu le jour dans ce contexte. Le but de cette thèse consiste à étudier expérimentalement et par la simulation deux techniques pour combattre les effets de la dispersion chromatique à travers l’ingénierie du chirp de la source. La première technique concerne les lasers DFB (Distributed Feedback Laser) modulés directement. Premièrement, un modèle complet et flexible d’un laser DFB développé au cours de la thèse a été exploité pour confirmer l’étude expérimentale des effets de phases du réseau de Bragg aux facettes sur le comportement du chirp. Les résultats ont montré l’existence de deux familles de lasers définies suivant la position du mode d’émission par rapport à la bande interdite. Deuxiémement, une étude théorique et expérimentale a montré la stabilisation et le contrôle du chirp des lasers DFB via la présence d'une rétroaction optique externe bien ajustée. La deuxième technique concerne le concept de la modulation duale des lasers modulateurs intégrés (D-EML : Dual Electroabsorption Modulated Laser) exploitant l’ajustement de la dérive en fréquence résultant de la juxtaposition d’une modulation de fréquence appliquée sur le laser et une modulation d’intensité appliquée sur le modulateur. L’évaluation expérimentale et théorique des performances du D-EML a permis de prouver sa compatibilité aux hauts débits (20, 25 et 40 Gb/s) ainsi que son efficacité par rapport à la modulation simple de l’EAM (Electro-Absorption Modulator). / Today, new higher-speed, low cost and low consumption optical sources are becoming a necessity for the deployment of access and metropolitan networks.The aim of this thesis is to study experimentally and by simulation two techniques in order to combat the chromatic dispersion effects through the chirp engineering of the source. The first technique concerns directly modulated DFB (Distributed FeedBack) lasers. First, a complete and flexible model of a DFB laser developed during the thesis has been used to confirm the experimental study of the facet phase effect on the chirp behavior. The results showed the existence of two laser’s families according to the position of the lasing mode with respect to the bandgap. Second, a theoretical and experimental study showed the chirp stabilization and control of DFB lasers due to the presence of a well adjusted external optical feedback.The second technique concerns the dual modulation concept of integrated modulated laser (D-EML : Dual Electroabsorption Modulated Laser) exploiting the adjustment of the chirp resulting from the juxtaposition of the frequency modulation applied to the laser and the intensity modulation applied to the modulator. Experimental and theoretical evalutation of D-EML performances has proven its compatibitlity with high bit-rates (20, 25 and 40 Gb/s) and its effectiveness with respect to the simple modulation of the EAM (Electroabsorption Modulator).

In this dissertation, we develop feedback control strategies that can be used for evacuating people. Pedestrian models are based on macroscopic or microscopic behavior. We use the macroscopic modeling approach, where pedestrians are treated in an aggregate way and detailed interactions are overlooked. The models representing evacuation dynamics are based on the laws of conservation of mass and momentum and are described by nonlinear hyperbolic partial differential equations. As such the system is distributed in nature. We address the design of feedback control for these models in a distributed setting where the problem of control and stability is formulated directly in the framework of partial differential equations. The control goal is to design feedback controllers to control the movement of people during evacuation and avoid jams and shocks. We design the feedback controllers for both diffusion and advection where the density of people diffuses as well as moves in a specified direction with time. In order to achieve this goal we are assuming that the control variables have no bounds. However, it is practically impossible to have unbounded controls so we modify the controllers in order to take the effect of control saturation into account. We also discuss the feedback control for these models in presence of uncertainties where the goal is to design controllers to minimize the effect of uncertainties on the movement of people during evacuation. The control design technique adopted in all these cases is feedback linearization which includes backstepping for higher order two-equation models, Lyapunov redesign for uncertain models and robust backstepping for two-equation uncertain models. The work also focuses on abstraction of evacuation system which focuses on obtaining models with lesser number of partial differential equations than the original one. The feedback control design of a higher level two-equation model is more difficult than the lower order one-equation model. Therefore, it is desirable to perform control design for a simpler abstracted model and then transform control design back to the original model. / Ph. D.

International Telemetering Conference Proceedings / October 23-26, 2000 / Town & Country Hotel and Conference Center, San Diego, California / This paper presents the results of installing a distributed feedback (DFB) laser transmitter and the appropriate optical receiver in an operational site. Frequencies from 1435 to 2400 megahertz are transported intact from a remote site to a local site. From the theoretical calculations, 10 dB of dynamic range may need to be recovered by the use of an automatic gain circuit. The actual device is a delight, needing no additional circuitry to meet specifications. Predictions of performance were made from calculations. The installed system was measured for 1 dB compression point and for figure of merit.

No description available.

This thesis presents studies of organic semiconductor lasers, including their operation when pumped by a light-emitting diode (LED), and their application as explosive sensors. The photophysics and amplified spontaneous emission (ASE) of star-shaped oligofluorene truxene molecules were investigated. These materials exhibit high gain and low optical loss in thin-film waveguides. Low ASE thresholds were achieved with the truxene T3 and T4. Second-order distributed feedback (DFB) lasers were fabricated, with pump threshold intensities below 0.5 kW/cm² and broad tunability of the emission. DFB lasers were demonstrated with a novel polymer BBEHP-PPV, pumped by a pulsed commercial InGaN LED. The laser emission occurred at 533 nm for peak drive current above 15 A. The output beams and pulse-dynamics of the lasers were investigated for the first time, along with a 'double-threshold' phenomenon that was observed in this long-pulse pumping regime. BBEHP-PPV lasers based on various types of diffractive resonators were also fabricated by UV nanoimprint-lithography (NIL). By optimising the resonator design and the fabrication, and the pump-beam geometry, polymer laser thresholds of ~60 W/cm², the lowest recorded for NIL lasers, were demonstrated, enabling them to be pumped by pulsed commercial LEDs and custom micro-LED arrays. One promising application of organic lasers is in explosive sensing. A polymer of intrinsic microporosity (PIM-1) was used to detect nitroaromatic vapours. Rapid detection of dinitrobenzene (DNB) of low vapour pressure was achieved by monitoring the photoluminescence and laser emission during exposure. In addition, a CMOS time-resolved fluorescence lifetime microsystem with a commercial green-emitting copolymer was used as a novel, portable sensor to detect DNB vapour. An InGaN LED pumped BBEHP-PPV laser was also used as a miniature sensor to detect 10 ppb of DNB. These highly sensitive hybrid sensors could be used in humanitarian demining, complementing existing technologies leading to improvement in the detection of hazardous objects.

This paper presents a distributed feedback and feedforward of discrete-time delta sigma modulator applications in the radio. We know the delta-sigma modulator using oversampling and noise shaping technique, thus we can relax the specifications of the components. This paper described the architectural differences and compare, the in-band signal is less sensitive to noise interference, and improve the resolution of the circuit. In the resonator, a simple structure with a small number of capacitor in resonator circuit. This paper uses the TSMC 0.18£gm process parameters to the simulation, implementation, and measurement. Our fourth-order discrete-time delta-sigma modulator specifications as follows: the input signal frequency is 10.7MHz, the sampling frequency is 42.8MHz, the signal bandwidth is 200kHz, oversampling rate is 107, and one bit quantizer.

Since their initial demonstration in 1994, quantum cascade lasers (QCLs) have become prominent sources of mid-infrared radiation. Over the years, a large scientific and engineering effort has led to a dramatic improvement in their efficiency and power output, with continuous wave operation at room temperature and Watt-level output power now standard. However, beyond this progress, new functionalities and capabilities need to be added to this compact source to enable its integration into consumer-ready systems. Two main areas of development are particularly relevant from an application standpoint and were pursued during the course of this thesis: wavelength control and wavefront engineering of QCLs. The first research direction, wavelength control, is mainly driven by spectroscopic applications of QCLs, such as trace gas sensing, process monitoring or explosive detection. We demonstrated three different capabilities, corresponding to different potential spectroscopic measurement techniques: widely tunable single longitudinal mode lasing, simultaneous lasing on multiple well-defined longitudinal modes, and simultaneous lasing over a broad and continuous range of the spectrum. The second research direction, wavefront engineering of QCLs, i.e. the improvement of their beam quality, is relevant for applications necessitating transmission of the QCL output over a large distance, for example for remote sensing or military countermeasures. To address this issue, we developed plasmonic lenses directly integrated on the facets of QCLs. The plasmonic structures designed are analogous to antenna arrays imparting directionality to the QCLs, as well as providing means for polarization control. Finally, a research interest in plasmonics led us to design passive flat optical elements using plasmonic antennas. All these projects are tied together by the involvement of Fourier analysis as an essential design tool to predict the interaction of light with various gratings and periodic arrays of grooves and scatterers. / Engineering and Applied Sciences

There is an increasing need for tuneable spectrally pure semiconductor laser sources as well as broadband and polarization insensitive semiconductor optical amplifiers based on the InGaASP/InP material system, to be monolithically integrated with other active and passive components in a photonic integrated circuit. This thesis aims to contribute to finding a solution through modelling, experimental characterization and design improvements. In this thesis we have analyzed laterally-coupled distributed feedback (LC-DFB) lasers. These lasers have the gratings etched directly out of the ridge sidewalls thus lowering the cost associated with the re-growth process required if the gratings were otherwise embedded above the active region. The performance characteristics are analyzed for the LC-DFB lasers partitioned into 1-, 2-, and 3-, electrodes with individual bias control at various operating temperatures. The laser exhibits a stable single mode emission at 1560 nm with a current tuning rate of ~14 pm/mA for a tuning of 2.25 nm. The side modes are highly suppressed with a maximum side-mode suppression ratio of 58 dB. The light-current characteristics show a minimum 40 mA threshold current, and power saturation occurring at higher injection currents. The linewidth characteristics show a minimum Lorentzian linewidth of 210 kHz under free-running and further linewidth reduction under feedback operation. The multi-electrode LC-DFB laser devices under appropriate and selective driving conditions exhibit a flat frequency modulation response from 0 to above 300 MHz. The multi-electrode configuration can thus be further exploited for certain requirements. Simulation results and design improvements are also presented. The experimental characterization of semiconductor optical amplifier (SOA) and Fabry-Perot (FP) laser operating in the E-band are also presented. For the SOA, the linear vertical and horizontal states of polarization corresponding to the transverse electric (TE) and transverse magnetic (TM) modes were considered. For various input power and bias, performance characteristics shows a peak gain of 21 dBm at 1360 nm, gain bandwidth of 60 nm and polarization sensitivity of under 3 dB obtained for the entire wavelength range analyzed from 1340 to 1440 nm. The analysis presented in this thesis show good results with room for improvement in future designs.