Semiconductor corrugated ridge waveguide (CRW) distributed feedback (DFB) lasers offer compelling advantages over standard DFB lasers. Indeed, the use of surface gratings etched on the ridge waveguide sidewalls in CRW-DFB devices avoids any epitaxial overgrowth. This provides a considerable simplification in the fabrication process, reducing cost and time of manufacturing, and ultimately increasing yield. It offers also the potential for monolithic integration with other devices, paving the way towards low-cost and mass-production of photonics integrated circuits. In recent years, the re-consideration of growth-free DFB lasers has drawn considerable attention, particularly with the current state-of-the-art photolithography machines. In this work, we present an experimental investigation on two generations of InGaAsP/InP multiple-quantum-well (MQW) CRW-DFB lasers that have been fabricated using stepper lithography. An early developed 1310 nm CRW-DFB laser showed stable single mode with high side-mode suppression ratios (SMSR) (>50 dB), albeit with thresholds higher than anticipated. A subsequent single-mode 1550 nm CRW-DFB laser showed stable operation with SMSR (>50 dB) and narrow spectral linewidths (≤250 kHz), observed for a wide range of current injection. Besides, novel multi-electrode CRW-DFB lasers have been tested. The experimental investigation showed that narrower linewidth (<150 kHz) and wide wavelength tunability (>3 nm) have been recorded using different multi-electrode current injection configurations. The application of a time-domain modeling approach for semiconductor CRW-DFB lasers is then described for the first time. We numerically studied the effect of the radiation modes on CRW-DFB laser properties by using time-domain coupled wave equations. High-order corrugated gratings with λ/4 phase-shit were analyzed, where the degree of longitudinal spatial hole burning (LSHB) can be effectively reduced by means of fine tuning of the grating duty cycle. Additionally, we showed how the side-mode suppression ratio can be predicted depending on the device geometry.

This thesis presents studies of organic semiconductor lasers, including their operation when pumped by a light-emitting diode (LED), and their application as explosive sensors. The photophysics and amplified spontaneous emission (ASE) of star-shaped oligofluorene truxene molecules were investigated. These materials exhibit high gain and low optical loss in thin-film waveguides. Low ASE thresholds were achieved with the truxene T3 and T4. Second-order distributed feedback (DFB) lasers were fabricated, with pump threshold intensities below 0.5 kW/cm² and broad tunability of the emission. DFB lasers were demonstrated with a novel polymer BBEHP-PPV, pumped by a pulsed commercial InGaN LED. The laser emission occurred at 533 nm for peak drive current above 15 A. The output beams and pulse-dynamics of the lasers were investigated for the first time, along with a 'double-threshold' phenomenon that was observed in this long-pulse pumping regime. BBEHP-PPV lasers based on various types of diffractive resonators were also fabricated by UV nanoimprint-lithography (NIL). By optimising the resonator design and the fabrication, and the pump-beam geometry, polymer laser thresholds of ~60 W/cm², the lowest recorded for NIL lasers, were demonstrated, enabling them to be pumped by pulsed commercial LEDs and custom micro-LED arrays. One promising application of organic lasers is in explosive sensing. A polymer of intrinsic microporosity (PIM-1) was used to detect nitroaromatic vapours. Rapid detection of dinitrobenzene (DNB) of low vapour pressure was achieved by monitoring the photoluminescence and laser emission during exposure. In addition, a CMOS time-resolved fluorescence lifetime microsystem with a commercial green-emitting copolymer was used as a novel, portable sensor to detect DNB vapour. An InGaN LED pumped BBEHP-PPV laser was also used as a miniature sensor to detect 10 ppb of DNB. These highly sensitive hybrid sensors could be used in humanitarian demining, complementing existing technologies leading to improvement in the detection of hazardous objects.

京都大学 / 0048 / 新制・課程博士 / 博士(工学) / 甲第18283号 / 工博第3875号 / 新制||工||1594(附属図書館) / 31141 / 京都大学大学院工学研究科電子工学専攻 / (主査)教授 野田 進, 教授 川上 養一, 教授 藤田 静雄 / 学位規則第4条第1項該当 / Doctor of Philosophy (Engineering) / Kyoto University / DFAM

The Quantum Cascade Laser (QCL)-based terahertz-over-fibre (ToF) concept combines the strength of QCLs as ultra-wide bandwidth, high speed data sources, with the mature optical fibre technology. In this thesis, for the first time, by fusing multiple technologies, digitally selected, electronically-switchable ToF concept is experimentally demonstrated. Furthermore, the digital mode selection principle and electronic tuning mechanism provided by novel aperiodic distributed feedback (ADFB) multi-band filters are presented. For the development of electronically tunable ADFB lasers, a range of bound-to-continuum and chirped superlattice terahertz (THz) QCLs are measured across the frequency range 2.9 – 4.5 THz. The availability of these active materials allowed rapid assessments of the optimum design parameters for subsequent measurements. First, a range of photonic lattice-engineered lasers operating at 4.4 THz are characterized and key design parameters identified. Following this initial development, full electrical and spectral characterization of ADFB lasers operating at 2.9 THz are presented. The novelty of this work lies in the first-ever successful demonstration of discretely tunable QCLs, operating at six distinct THz frequencies. The ADFB technology was experimentally applied using various device geometries and gain dynamics. Toward this aim, results are presented for a Y coupled QCL architecture, showing that complex on-chip signal manipulation can be extended into the THz regime. In addition, it is demonstrated that ADFB technology provides broadband multi-channel optical filtering for the entire gain bandwidth. It is shown that discrete, purely electronic, tuning of simultaneous dual colour output can be achieved. Multi band optical filter functions derived from ADFB gratings possess highly nonlinear dispersion across the filter bandwidth and are found to modify the gain-induced, driving current-dependent continuous mode tuning. This thesis, therefore, presents a systematic experimental analysis of the dispersion engineered continuous fine-tuning in THz QCLs. In the final two chapters, the thesis presents, for the first time, transmission of tunable THz signals over standard single-mode optical fibre by up converting 2.9 THz QCL radiation via intra-cavity nonlinear mixing with an optical fibre-injected near-infrared (NIR) carrier in the 1.3 µm band. Discrete and continuous tuning technologies, as developed in chapters 3 – 5, are now successfully transferred to THz sidebands on the NIR carrier, extracted via a butt coupled single mode fibre and recorded using an optical spectrum analyzer. The major novel outcome of this thesis is the first demonstration of electronically tunable phase-matched points in a THz plasmon waveguide. The key breakthrough is the experimental confirmation of the photonic band-gap engineering of group velocity of THz signals – as both ‘fast’ and ‘slow’ switchable side bands are observed. Such novel nonlinear up-conversion of spectrally flexible THz signals may open up new possibilities for ultrafast THz telecom frameworks.

Die vorliegende Arbeit beschäftigt sich mit der Entwicklung und Optimierung von Terahertz-Quantenkaskadenlasern (THz-QCLs) für die Anwendung als Lokaloszillator in THz-Heterodyndetektoren, insbesondere für die Detektion der astronomisch wichtigen Sauerstoff (OI) Linie bei 4.75 THz. Hierfür wurden zunächst unterschiedliche QCL-Heterostrukturen untersucht. Basierend auf einer Heterostruktur, welche schnelle Intersubbandübergänge über Streuung an Phononen ausnutzt, konnten QCLs mit hoher Ausgangsleistung und niedriger Betriebsspannung bei 3 THz erzielt werden. Während diese Laser auf dem Materialsystem GaAs/Al_xGa_(1-x)As mit $x=0.15$ basieren, führt die Erhöhung des Al-Anteils auf x=0.25 für ähnliche Strukturen zu sehr niedrigen Schwellstromdichten. Durch schrittweise Optimierungen gelang es, QCLs zu realisieren, die bei 4.75 THz emittieren. Mit Hilfe von lateralen Gittern erster Ordnung für die verteilte Rückkopplung (DFB) konnten Einzelmoden-Dauerstrichbetrieb mit hoher Ausgangsleistung, sowie Einzelmoden-Betrieb innerhalb des spezifizierten Frequenzbereichs bei 4.75 THz erzielt werden. Eine allgemeine Methode zur Bestimmung der DFB-Kopplungskonstanten erlaubt eine gute Beschreibung der Laser innerhalb der etablierten Theorie der gekoppelten Moden für DFB-Laser mit reflektiven Endfacetten. Oft steht das Auftreten negativer differentieller Leitfähigkeit bei höheren Feldstärken und die damit verbundenen Bildung von elektrischer Felddomänen (EFDs) im Konflikt mit einem stabilen Betrieb der THz-QCLs. Es wird gezeigt, dass stationäre EFDs mit Diskontinuitäten in der statischen Licht-Strom-Spannungskennlinie verbunden sind, während Selbstoszillationen, verursacht durch nicht-stationäre EFDs, eine zeitliche Modulation der Ausgangsleistung bewirken. Mit Hilfe einer effektiven Driftgeschwindigkeit für QCLs lassen sich viele der beobachteten Phänomene durch die nichtlinearen Transportgleichungen für schwach gekoppelte Übergitter beschreiben. / This thesis presents the development and optimization of terahertz quantum-cascade lasers (THz QCLs) as sources for heterodyne receivers. A particular focus is on single-mode emitters for the heterodyne detection of the important astronomic oxygen (OI) line at 4.75 THz. Various active-region designs are investigated. High-output-power THz QCLs with low operating voltages and emission around 3 THz are obtained for an active region, which involves phonon-assisted intersubband transitions. While these QCLs are based on a GaAs/Al_xGa_(1-x)As heterostructure with x=0.15, similar heterostructures with x=0.25 allowed for very low threshold current densities. By successive modifications of the active-region design, THz QCLs have been optimized toward the desired frequency at 4.75 THz. To obtain single-mode operation, first-order lateral distributed-feedback (DFB) gratings are investigated. It shows that such gratings allow for single-mode operation in combination with high continuous-wave (cw) output powers. A general method is presented to calculate the coupling coefficients of lateral gratings. In conjunction with this method, the lasers are well described by the coupled-mode theory of DFB lasers with two reflective end facets. Single-mode operation within the specified frequency bands at 4.75 THz is demonstrated. Stable operation of THz QCLs is often in conflict with the occurrence of a negative differential resistance (NDR) regime at elevated field strengths and the formation of electric-field domains (EFDs). Stationary EFDs are shown to be related to discontinuities in the cw light-current-voltage characteristics, while non-stationary EFDs are related to current self-oscillations and cause a temporal modulation of the output power. To model such effects, the nonlinear transport equations of weakly coupled superlattices are adopted for QCLs by introducing an effective drift velocity-field relation.