Spelling suggestions: "subject:"electroconvulsive"" "subject:"photoconductive""
1 |
Studium vlivu struktury na rezistivitu silikátového kompozitu / Study of the influence of structure on the resistivity of silicate compositesUher, Vojtěch January 2022 (has links)
Electroconductive silicate-based composites are advanced materials that allow building structures to perform several different functions simultaneously. Addressing the issues of their development and use is a suitable topic for research work. The aim of this work is to study the effect of structure on the resistivity of silicate composite. The structure of electrically conductive composites is studied on dry cement paste and mortar mixtures as well as on test bodies made of hardened cement paste and mortar after 28 days of curing. Based on the analysis of the raw materials, six suitable electroconductive fillers are selected based on particle size, resistivity, and water absorption. The parameters of dry cement paste and hardened cement paste with replacement of 4-19 wt. % cement by the selected fillers are determined. Two of the fillers are selected for use in dry and hardened mortar. Resistivity is determined for all dry mixes and hardened composites variants, and percolation thresholds are approximately determined. By studying the structure of the selected variants, it is shown that the most important parameters that have the greatest influence on the resistivity of the silicate composites are mainly the particle size and the intrinsic resistivity of the electrically conductive filler. For silicate composites in the hardened state, the volume of hydration products, especially portlandite and C-S-H gels, also has a significant influence. For both dry blends and hardened composites, it was found that the smaller the particle size of the electroconductive filler, the smaller the representation needed to reach the percolation threshold. Portlandite and C-S-H gels in the volume of the hardened composite cause its high resistivity. The resistivity of the hardened composite is always higher than that of the dry blends. Thus, the proportion of electroconductive filler needed to reach the percolation threshold is higher in hardened composites than in dry mixes. The resist
|
2 |
Preparation of Electroconductive Paper by Deposition of Conducting PolymerMontibon, Elson January 2009 (has links)
<p>The thesis describes an investigation into the interaction between the conducting polymer and cellulosic materials, and the preparation of electroconductive paper. The adsorption behavior of the conducting polymer onto cellulosic materials was characterized. Poly(3,4-ethylenedioxythiophene) doped with poly(4-styrene sulfonate) (PEDOT:PSS) was used as conducting polymer because of its attractive properties in terms of conductivity, water solubility, and environmental stability. The model substrate used for adsorption was microcrystalline cellulose (MCC). Various pH levels and salt concentrations were explored to completely understand the adsorption behavior of PEDOT:PSS. The variation in surface charge characteristics when the pH and salt concentration were changed was monitored by polyelectrolyte titration and zeta potential measurement. The adsorption isotherm showed a broad molecular distribution of the conducting polymer and considerable interaction between the polymer and MCC. As the pH of the solution was increased, the adsorbed amount decreased. With varying salt concentrations, the adsorption passed through a maximum. The extent of deposition of PEDOT:PSS on the surface of cellulosic fibers was investigated using X-ray Photoelectron Spectroscopy (XPS) with a commercial base paper as substrate. XPS analysis of dip-coated paper samples showed PEDOT enrichment on the surface. The degree of washing the dip-coated paper with acidic water did not significantly affect the PEDOT enrichment on the surface.</p><p> </p><p>A base paper was coated with PEDOT:PSS blends to produce electroconductive papers. The bulk conductivities (σ<sub>dc</sub>) of the coated papers were measured using a four-probe technique and impedance spectroscopy. One-side and two-side coating gave comparable conductivity levels. Various organic solvents added to the PEDOT:PSS dispersion at different concentrations showed various effects on the bulk conductivity of the coated paper. Blends containing sorbitol and isopropanol did not enhance the bulk conductivity of the coated paper, and at high concentrations these organic solvents lowered the conductivity. Paper samples coated with a PEDOT:PSS blend containing N-methylpyrrolidinone (NMP) and dimethyl sulfoxide (DMSO) exhibited a higher conductivity than when coated with pure PEDOT:PSS, due to conformational changes and their plasticizing effect. The effect of calendering was investigated and only the sample subjected to 174 kN/m line load after coating showed significant conductivity enhancement. The addition of TiO<sub>2</sub> pigment lowered the bulk conductivity of the paper. Contact angle measurements were made to monitor the effect of coating the paper with PEDOT:PSS blends on the hydrophilicity of the paper samples. The amount of PEDOT:PSS deposited in the fiber network was determined using total sulfur analysis. Thus, this study makes use of conventional paper surface treatment as method for achieving bulk conductivity of paper in the semi-conductor range without significantly decreasing the paper strength.</p> / Printed Polymer Electronics
|
3 |
Preparation of Electroconductive Paper by Deposition of Conducting PolymerMontibon, Elson January 2009 (has links)
The thesis describes an investigation into the interaction between the conducting polymer and cellulosic materials, and the preparation of electroconductive paper. The adsorption behavior of the conducting polymer onto cellulosic materials was characterized. Poly(3,4-ethylenedioxythiophene) doped with poly(4-styrene sulfonate) (PEDOT:PSS) was used as conducting polymer because of its attractive properties in terms of conductivity, water solubility, and environmental stability. The model substrate used for adsorption was microcrystalline cellulose (MCC). Various pH levels and salt concentrations were explored to completely understand the adsorption behavior of PEDOT:PSS. The variation in surface charge characteristics when the pH and salt concentration were changed was monitored by polyelectrolyte titration and zeta potential measurement. The adsorption isotherm showed a broad molecular distribution of the conducting polymer and considerable interaction between the polymer and MCC. As the pH of the solution was increased, the adsorbed amount decreased. With varying salt concentrations, the adsorption passed through a maximum. The extent of deposition of PEDOT:PSS on the surface of cellulosic fibers was investigated using X-ray Photoelectron Spectroscopy (XPS) with a commercial base paper as substrate. XPS analysis of dip-coated paper samples showed PEDOT enrichment on the surface. The degree of washing the dip-coated paper with acidic water did not significantly affect the PEDOT enrichment on the surface. A base paper was coated with PEDOT:PSS blends to produce electroconductive papers. The bulk conductivities (σdc) of the coated papers were measured using a four-probe technique and impedance spectroscopy. One-side and two-side coating gave comparable conductivity levels. Various organic solvents added to the PEDOT:PSS dispersion at different concentrations showed various effects on the bulk conductivity of the coated paper. Blends containing sorbitol and isopropanol did not enhance the bulk conductivity of the coated paper, and at high concentrations these organic solvents lowered the conductivity. Paper samples coated with a PEDOT:PSS blend containing N-methylpyrrolidinone (NMP) and dimethyl sulfoxide (DMSO) exhibited a higher conductivity than when coated with pure PEDOT:PSS, due to conformational changes and their plasticizing effect. The effect of calendering was investigated and only the sample subjected to 174 kN/m line load after coating showed significant conductivity enhancement. The addition of TiO2 pigment lowered the bulk conductivity of the paper. Contact angle measurements were made to monitor the effect of coating the paper with PEDOT:PSS blends on the hydrophilicity of the paper samples. The amount of PEDOT:PSS deposited in the fiber network was determined using total sulfur analysis. Thus, this study makes use of conventional paper surface treatment as method for achieving bulk conductivity of paper in the semi-conductor range without significantly decreasing the paper strength. / Printed Polymer Electronics
|
4 |
Protection cathodique du béton armé par revêtement electro-conducteur autonome / Cathodic protection in reinforced concrete structures using an electroconductive coatingSassine, Elie 06 July 2018 (has links)
La protection cathodique par courant imposé (PCCI) est l’une des techniques adoptées pour limiter ou annihiler la corrosion dans le béton armé. Le but de cette thèse est de développer des revêtements suffisamment conducteurs et autonomes pour s’affranchir de l’utilisation des anodes primaires métalliques lors de la PCCI. Ce mémoire est formé de quatre parties principales :I. La première partie résume la recherche bibliographique réalisée. II. Cette partie sera consacrée à la formulation des revêtements électro-conducteurs par dispersion des poudres-pigmentaires conductrices (métallique ou carbone) dans une résine acrylique ou polyuréthane. III. L’efficacité des revêtements électro-conducteurs en tant qu’anode autonome est étudiée dans cette partie. IV. La dernière partie présente des essais de PCCI réalisés en continu pendant 6 mois sur des dallettes corrodées. Des spécimens témoins non corrodés sont aussi placés dans le même environnement sans protection cathodique. / Impressed Current Cathodic Protection (ICPP) is one of the electrochemical techniques applied to limit or annihilate corrosion. The aim of this thesis is to develop sufficiently conductive and autonomous coatings to overcome the use of primary anodes during ICPP. This thesis is based on four main parts:I. The first part summarizes a bibliographic review of corrosion in reinforced concrete. II. This part will focus on the formulation of electroconductive coatings by mixing conductive powders (metallic or carbon) with an acrylic or polyurethane resin. III. The effectiveness of electroconductive coatings as an autonomous anode is studied in this section. IV. The last part presents ICCP tests carried out continuously for 6 months on corroded slabs. Non-corroded specimens are also placed in the same environment without cathodic protection in order to make a comparative analysis.
|
5 |
Modification of Paper into Conductive Substrate for Electronic Functions : Deposition, Characterization and DemonstrationMontibon, Elson January 2011 (has links)
The thesis investigates the modification of paper into an ion- and electron-conductive material, and as a renewable material for electronic device. The study stretches from investigating the interaction between the cellulosic materials and the conducting polymer to demonstrating the performance of the conductive paper by printing the electronic structure on the surface of the conductive paper. Conducting materials such as conducting polymer, ionic liquids, and multi-wall carbon nanotubes were deposited into the fiber networks. In order to investigate the interaction between the conducting polymer and cellulosic material, the adsorption of the conducting polymer poly(3,4-ethylenedioxythiophene): poly(4-styrene sulfonate) (PEDOT:PSS) onto microcrystalline cellulose (MCC) was performed. Electroconductive papers were produced via dip coating and rod coating, and characterized. The Scanning Electron Microscopy (SEM) / Energy Dispersive Spectroscopy (EDS) images showed that the conducting polymer was deposited in the fiber and in fiber-fiber contact areas. The X-ray Photoelectron Spectroscopy (XPS) analysis of dip-coated paper samples showed PEDOT enrichment on the surface. The effects of fiber beating and paper formation, addition of organic solvents and pigments (TiO2, MWCNT), and calendering were investigated. Ionic paper was produced by depositing an ionic liquid into the commercial base paper. The dependence to temperature and relative humidity of the ionic conductivity was also investigated. In order to reduce the roughness and improve its printability, the ionic paper was surface-sized using different coating rods. The bulk resistance increased with increasing surface sizing. The electrochemical performance of the ionic paper was confirmed by printing PEDOT:PSS on the surface. There was change in color of the polymer when a voltage was applied. It was demonstrated that the ionic paper is a good ionic conductor that can be used as component for a more compact electronic device construction. Conductive paper has a great potential to be a flexible substrate on which an electronic structure can be constructed. The conduction process in the modified paper is due to the density of charge carriers (ions and electrons), and their short range mobility in the material. The charge carrying is believed to be heterogeneous, involving many charged species as the paper material is chemically heterogeneous. / <p>Fel ordningsnummer (2010:28) är angivet på omslaget av fulltextfilen.</p> / Printed Polymer Electronics on Paper
|
6 |
Strategies for Guidance and Electrical and Biological Stimulation in a Neural Regeneration DeviceGisbert Roca, Fernando 18 November 2022 (has links)
Tesis por compendio / [ES] Actualmente las lesiones del sistema nervioso periférico que conllevan una pérdida de continuidad de los haces axonales suelen implicar secuelas de tipo permanente. Es cierto que en el sistema nervioso periférico existe una cierta regeneración natural de los tractos axonales dañados, pero solamente cuando el espacio entre ambos extremos de la lesión es pequeño, como máximo de 5 mm. Si el espacio es mayor que esta distancia la regeneración no sucede de forma natural y se crea un neuroma traumático. Por tanto, estas lesiones largas requieren de una intervención quirúrgica para puentear la lesión, normalmente con un nervio autógrafo del propio paciente o un nervio alógrafo de un cadáver. No obstante, su uso presenta diversos inconvenientes, como la morbilidad del sitio donante donde puede ocurrir un neuroma, la necesidad de realizar una segunda cirugía, la diferencia de tamaño entre nervio receptor y donante o la necesidad de inmunosupresión en el caso de los nervios alógrafos. Por ello, la ingeniería de tejidos trabaja en el desarrollo de los conductos de guiado nervioso que incorporan estrategias para guiar topográficamente la regeneración, así como células y moléculas bioactivas.
La presente tesis doctoral presenta un nuevo conducto de guiado nervioso con una aproximación multimodular para su aplicación en la regeneración de lesiones nerviosas largas (a partir de 15 mm) que hace uso de conductos tubulares huecos modulares de ácido hialurónico (HA) que contienen en su interior una estructura tubular de microfibras de ácido poliláctico (PLA). La estructura fibrilar aporta un guiado topográfico necesario para guiar el crecimiento axonal durante la regeneración a la vez que mantiene unidos los diferentes módulos de HA. Por su parte, los conductos de HA son un hidrogel que evita adherencias con el tejido circundante. A su vez, proporcionan un soporte sobre el que pueden crecer células presembradas. En concreto se ha optado por presembrar células de Schwann, las cuales son unas células gliales de soporte críticas para la regeneración del sistema nervioso periférico. Se ha observado que dichas células son capaces recubrir por completo las paredes internas de los conductos de HA formando una estructura tipo vaina, así como de recubrir las microfibras de PLA creciendo en dirección longitudinal. Los experimentos in vivo en modelo de nervio ciático de conejo han mostrado que la aproximación multimodular mejora significativamente la regeneración nerviosa gracias a proporcionar una mejor neovascularización. A su vez, gracias a las células de Schwann presembradas se ha logrado una mejora adicional de la regeneración nerviosa gracias a su efecto favorecedor del crecimiento axonal.
Además, se han estudiado diferentes mejoras aplicables al conducto de guiado nervioso con el objetivo de mejorar los resultados obtenidos in vivo. Gracias a la incorporación de fibroína de seda a los conductos de HA se ha logrado mejorar sus propiedades mecánicas y biológicas. Asimismo, también se ha desarrollado un sustrato electroconductor de microfibras de PLA recubiertas con el polímero electroconductor Polipirrol gracias al cual se ha observado in vitro que es capaz de mejorar el crecimiento axonal al aplicar una estimulación eléctrica. Además, mediante un sistema de modificación génica de las células de Schwann por electrotransfección se ha logrado aumentar su secreción del factor neurotrófico derivado del cerebro (BDNF), gracias a lo cual se ha observado que se incrementa la velocidad de crecimiento axonal in vitro. / [CA] Actualment les lesions del sistema nerviós perifèric que comporten una pèrdua de continuïtat dels feixos axonals solen implicar seqüeles de tipus permanent. És cert que al sistema nerviós perifèric hi ha una certa regeneració natural dels tractes axonals danyats, però només quan l'espai entre ambdós extrems de la lesió és petit, com a màxim de 5 mm. Si l'espai és més gran que aquesta distància la regeneració no succeeix de manera natural i es crea un neuroma traumàtic. Per tant, aquestes lesions llargues requereixen una intervenció quirúrgica per pontejar la lesió, normalment amb un nervi autògraf del pacient o un nervi al·lògraf d'un cadàver. No obstant això, el seu ús presenta diversos inconvenients, com la morbilitat del lloc donant on pot ocórrer un neuroma, la necessitat de fer una segona cirurgia, la diferència de mida entre nervi receptor i donant o la necessitat d'immunosupressió en el cas dels nervis al·lògrafs . Per això, l'enginyeria de teixits treballa en el desenvolupament dels conductes de guiatge nerviós que incorporen estratègies per guiar topogràficament la regeneració, així com cèl·lules i molècules bioactives.
Aquesta tesi doctoral presenta un nou conducte de guiatge nerviós amb una aproximació multimodular per a la seva aplicació en la regeneració de lesions nervioses llargues (a partir de 15 mm) que fa ús de conductes tubulars buits modulars d'àcid hialurònic (HA) que contenen al seu interior una estructura tubular de microfibres d'àcid polilàctic (PLA). L'estructura fibril·lar aporta un guiatge topogràfic necessari per guiar el creixement axonal durant la regeneració alhora que manté units els diferents mòduls d'HA. Per part seva, els conductes d'HA són un hidrogel que evita adherències amb el teixit circumdant. Alhora, proporcionen un suport sobre el qual poden créixer cèl·lules presembrades. En concret s'ha optat per presembrar cèl·lules de Schwann, les quals són unes cèl·lules glials de suport crítiques per a la regeneració del sistema nerviós perifèric. S'ha observat que aquestes cèl·lules són capaces de recobrir completament les parets internes dels conductes d'HA formant una estructura tipus beina, així com de recobrir les microfibres de PLA creixent en direcció longitudinal. Els experiments in vivo en model de nervi ciàtic de conill han mostrat que l'aproximació multimodular millora significativament la regeneració nerviosa gràcies a proporcionar una millor neovascularització. Alhora, gràcies a les cèl·lules de Schwann presembrades s'ha aconseguit una millora addicional de la regeneració nerviosa gràcies al seu efecte afavoridor del creixement axonal.
A més, s'han estudiat diferents millores aplicables al conducte de guiatge nerviós per tal de millorar els resultats obtinguts in vivo. Gràcies a la incorporació de fibroïna de seda als conductes d'HA s'ha aconseguit millorar les seues propietats mecàniques i biològiques. També s'ha desenvolupat un substrat electroconductor de microfibres de PLA recobertes amb el polímer electroconductor Polipirrol gràcies al qual s'ha observat in vitro que és capaç de millorar el creixement axonal quan s'aplica una estimulació elèctrica. A més, mitjançant un sistema de modificació gènica de les cèl·lules de Schwann per electrotransfecció s'ha aconseguit augmentar la secreció del factor neurotròfic derivat del cervell (BDNF), gràcies a la qual cosa s'ha observat que s'incrementa la velocitat de creixement axonal in vitro. / [EN] Currently, lesions of the peripheral nervous system that lead to a loss of continuity of the axonal bundles usually involve permanent sequelae. It is true that in the peripheral nervous system there is some natural regeneration of damaged axonal tracts, but only when the space between the two ends of the lesion is small, at most 5 mm. If the gap is greater than this distance, regeneration does not occur naturally, and a traumatic neuroma is created. Therefore, these long injuries require surgical intervention to bridge the injury, usually with an autograph nerve from the patient or an allograph nerve from a cadaver. However, its use has various drawbacks, such as the morbidity of the donor site where a neuroma can occur, the need to perform a second surgery, the difference in size between the recipient and donor nerves, or the need for immunosuppression in the case of allograft nerves. For this reason, tissue engineering works on the development of nerve guidance conduits that incorporate strategies to topographically guide the regeneration, as well as cells and bioactive molecules.
This doctoral thesis presents a new nerve guidance conduit with a multimodular approach for its application in the regeneration of long nerve lesions (from 15 mm) that makes use of modular hollow tubular conduits of hyaluronic acid (HA) that contain in their inside a tubular structure of microfibers of polylactic acid (PLA). The fibrillar structure provides the necessary topographic guidance to guide axonal growth during regeneration while keeping the different HA modules together. For their part, the HA conduits are a hydrogel that prevents adhesions with the surrounding tissue. In turn, they provide a support on which preseeded cells can grow. Specifically, it has been decided to pre-seed Schwann cells, which are glial support cells that are critical for the regeneration of the peripheral nervous system. It has been observed that these cells are capable of completely covering the inner walls of the HA conduits, forming a sheath-like structure, as well as covering the PLA microfibers by growing in a longitudinal direction. In vivo experiments in a rabbit sciatic nerve model have shown that the multimodular approach significantly improves nerve regeneration by providing better neovascularization. In turn, thanks to the pre-seeded Schwann cells, an additional improvement in nerve regeneration has been achieved thanks to its promoting effect on axonal growth.
In addition, different improvements applicable to the nerve guidance conduit have been studied with the aim of improving the results obtained in vivo. Thanks to the incorporation of silk fibroin into HA conduits, their mechanical and biological properties have been improved. Likewise, an electroconductive substrate of PLA microfibers coated with the electroconductive polymer Polypyrrole has also been developed, thanks to which it has been observed in vitro that it is capable of improving axonal growth by applying electrical stimulation. In addition, by means of a gene modification system of Schwann cells by electrotransfection, it has been possible to increase their secretion of brain-derived neurotrophic factor (BDNF), thanks to which it has been observed that the speed of axonal growth is increased in vitro. / Agradezco la ayuda de los diferentes proyectos del Ministerio de
Economía y Competitividad del Gobierno de España que han hecho posible la
financiación de esta tesis doctoral: MAT2015-66666-C3-1-R, DPI2015-72863-EXP,
AEI RTI2018-095872-B-C21-C22/ERDF y FPU16/01833 del Ministerio de Universidades del Gobierno de España, sin la cual no
hubiera podido realizar esta tesis doctoral. / Gisbert Roca, F. (2022). Strategies for Guidance and Electrical and Biological Stimulation in a Neural Regeneration Device [Tesis doctoral]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/189937 / Compendio
|
7 |
Možnosti elektrického propojení součástek v automobilových zámcích / Different methods of connecting electrical parts in car locksKollár, Pavel January 2011 (has links)
This Diploma thesis is aimed at various ways of connecting electrical parts in car locks. This part of the thesis includes technologies of electric cables, printed circuit boards, lead frames, 3D-MID technology and technology of electroconductive plastics materials. Listed technologies are compared. The aim of the practical thesis portion is the application of electroconductive plastic materials on the given part. For this purpose necessary changes were designed in the provided small series injection mold. The thesis also includes drawing documentation of the designed construction changes in the injection mold, as well as economic appraisal of the prototype manufacturing fees.
|
Page generated in 0.1511 seconds