In the BGA family package, plating bars must be added in the manufactured processing , However they will cause discontinuities[1]¡Bradiation effect[2] and bad transmission efficiency[3]~[6].This paper considers the signal transmission problem caused by the couple plating lines. This thesis starts from analyzing the different terminations of the couple lines, then proposes a novel L-stub element structure which can decrease the crosstalk noise efficiently on the plating lines. Discussion of the L-stub length ratio, L-stub position and the numbers of the L-stub then provides the useful range. The basic idea is to use the reflection of source to cancel the original couple and doesn¡¦t have to add additional element. In addition, it compares well with other methods which are also designed for reducing crosstalk and circuits are implemented to prove our design. Last of all, using the eye diagram to manifest the signal quality improvement.

With smaller electronic devices and higher transmission speeds, a digital circuit will cause potential electromagnetic interference (EMI) and signal integrity (SI) problems. Nowadays, the flexible printed circuit board (FPC) is widely used in electronic systems, especially in the video circuit. In this thesis, we used transmission line model to explain effect of the structure of the flexible printed circuit board transmission lines. Eye-diagram is a fast and convenient tool to analyze the quality of the high speed transmission, and we can use the equivalent model to substitute for the electromagnetic (EM) model to simulate the performance. We used differential circuit and the reflection gain to increase the height and width parameters of Eye-diagram, and make the quality of signal transmission higher. For video driver circuit, since the terminal resistance is different depending on whether the IC is on or off, the standard probe cannot measure mixed-mode S-parameter directly due to the connectors. Thus, we provided a de-embedding method to remove the effects of high speed interconnect line on the test board. Finally, we use a simple structure to verify the method, and it can be used to measure mixed-mode S-parameter on the standard of Mobile Industry Processor Interface (MIPI) for D-PHY, v0.90.00.

ITC/USA 2007 Conference Proceedings / The Forty-Third Annual International Telemetering Conference and Technical Exhibition / October 22-25, 2007 / Riviera Hotel & Convention Center, Las Vegas, Nevada / Modern telemetry systems require flexible bit rate telemetry encoders in order to optimize mission formats for varying data rate requirements and/or signal to noise conditions given a fixed transmitter power. Implementing a variable bit rate telemetry encoder requires consideration of several possible architectural topologies that place different system requirements on data acquisition modules within the encoder in order to maintain adequate signal fidelity of sensor information. This paper focuses on the requirements, design considerations and tradeoffs associated with differing architectural topologies for implementing a variable bit rate encoder and the resulting implications on the encoder systems data acquisition units.

It has been well reported that the use of multidimensional constellation signals can help to reduce the bit error rate in Additive Gaussian channels by using the hyperspace geometry more efficiently. Similarly, in fading channels, dimensionality provides an inherent signal space diversity (distinct components between two constellations points), so the amplitude degradation of the signal are combated significantly better. Moreover, the set of n-dimensional signals also provides great compatibility with various Trellis Coded modulation schemes: N-dimensional signaling joined with a convolutional encoder uses fewer redundant bits for each 2D signaling interval, and increases intra-subset minimum squared Euclidean distance (MSED) to approach the ultimate capacity limit predicted by Shannon's theory. The multidimensional signals perform better for the same complexity than two-dimensional schemes. The inherent constellation expansion penalty factor paid for using classical mapping structures can be decreased by enlarging the constellation's dimension. In this thesis, a multidimensional signal set construction paradigm that completely avoids the constellation expansion penalty is used in Band-limited channels and in fading channels. As such, theoretical work on performance analysis and computer simulations for Quadrature-Quadrature Phase Shift Keying (Q2PSK), Constant Envelope (CE) Q2PSK, and trellis-coded 16D CEQ2PSK in ideal band-limited channels of various bandwidths is presented along with a novel discussion on visualization techniques for 4D Quadrature-Quadrature Phase Shift Keying (Q2PSK), Saha's Constant Envelope (CE) Q2PSK, and Cartwright's CEQ2PSK in ideal band-limited channels. Furthermore, a metric designed to be used in fading channels, with Hamming Distance (HD) as a primary concern and Euclidean distance (ED) as secondary is also introduced. Simulation results show that the 16D TCM CEQ2PSK system performs well in channels with AWGN and fading, even with the simplest convolutional encoder tested; achievable coding gains using 16-D CEQ2PSK Expanded TCM schemes under various conditions are finally reported.

In this thesis, a detailed study of the electrical and optical characterisations of Heterojuction Bipolar Transistors (HBTs) for optical detection is presented. By comparing both DC and optical characterisations between In0.49Ga0.51P/GaAs Single Heterojuction Bipolar Transistors (SHBTs) and Double Heterojuction Bipolar Transistors (DHBTs), the advantages of using the DHBT as a short wavelength detector are shown. Phenomena related to the base region energy band bending in the DHBT caused by a self-induced effective electric field is discussed and its effects on the performance of the device are elaborated. The use of an eye diagram has been employed to provide requisite information for performance qualification of SHBT/DHBT devices. These give a more detailed understanding compared to conventional S-parameters method. A detailed comparison of In0.49Ga0.51P/GaAs SHBT and DHBT performance using an eye diagram as a functional tool by adopting a modified T-shaped small signal equivalent circuit are given. By adopting this modified T-shaped small signal equivalent circuit, the use of In0.49Ga0.51P/GaAs Double Heterojuction Phototransistors (DHPT) as a short wavelength photodetector is analysed. It is therefore shown that an eye diagram can act as a powerful tool in HBTs/HPTs design optimisations, for the first time in this work. In order to predict the spectral response (SR) and optical characterisations of GaAs-based HPTs, a detailed theoretical absorption model is also presented. The layer dependence of an optical flux absorption profile, along with doping dependent absorption coefficients are taken into account for the optical characterisation prediction. With the aim of eliminating the limitation of current gain as a prerequisite, analytical modelling of SR has been developed by resolving the continuity equation and applying realistic boundary conditions. Then, related physical parameters and a layer structure profile are used to implement simulations. A good agreement with the measured results of the Al0.3Ga0.7As/GaAs HPT is shown validating the proposed theoretical model.

Master’s thesis engages in the impact of polarization mode dispersion on optical communication system. Polarization mode dispersion is mathematically described by Stoke’s and Jone’s space and ensure the theoretic causes of the rise of polarization mode dispersion that are divided on the external and internal effects. On the basis of these effects grow up a differential group delay (DGD) which makes causes that individual polarization modes have between them a time delay and limitation of maximum bit rate. Then master´s thesis analyses the influence of the polarization mode dispersion on the pulse enlargement and on the modulation signal. In this work, there are described the most applicated optical modulation formats. Polarization mode dispersion has also influence on the bit error rate of optical fibre link and closing of eye diagram too. Eye diagram is used to view the transmission characteristics and diagnoses the channel errors. Eye diagram is connected with the definitions as a bit error rate (BER) and signal-to-noise ratio (SNR) that are explained in this work too. Following the gained experiences it was designed an useful graphic interface to display the effect of the polarization mode dispersion on the transmitted signal. Realization of the graphic interface is created in the program MATLAB. In Matlab-Simulink are created six models according to the kind of modulations with characteristic AWGN (Additive White Gaussian Noise) channel. Program was tested for a typical values. In all calculations it is counted only with the losses that are caused by the polarization mode dispersion. It is not calculated with the losses that are caused by a chromatic dispersion and attenuation. At the end of this work are evaluated all types of modulation formats depending on the polarization mode dispersion, optical fibre length, price and complexity of the realization. Atteined results of my master’s thesis are compared with two foreign articles.

This thesis proposes a decision-feedback equalizer (DFE) scheme for blind ADC-based receivers to overcome the challenges introduced by blind sampling. It presents the design, simulation, and implementation of a 5Gb/s speculative DFE for a 2x blind ADC-based receiver. The complete receiver, including the ADC, the DFE, and a 2x blind clock and data recovery (CDR) circuit, is implemented in Fujitsu’s 65-nm CMOS process. Measurements of the fabricated test-chip confirm 5Gb/s data recovery with bit error rate (BER) less than 1e−12 in the presence of a test channel introducing 13.3dB of attenuation at the Nyquist frequency of 2.5GHz. The receiver tolerates 0.24UIpp of high-frequency sinusoidal jitter (SJ) in this case. Without the DFE, the BER exceeds 1e−8 even when no SJ is applied.

This thesis proposes a decision-feedback equalizer (DFE) scheme for blind ADC-based receivers to overcome the challenges introduced by blind sampling. It presents the design, simulation, and implementation of a 5Gb/s speculative DFE for a 2x blind ADC-based receiver. The complete receiver, including the ADC, the DFE, and a 2x blind clock and data recovery (CDR) circuit, is implemented in Fujitsu’s 65-nm CMOS process. Measurements of the fabricated test-chip confirm 5Gb/s data recovery with bit error rate (BER) less than 1e−12 in the presence of a test channel introducing 13.3dB of attenuation at the Nyquist frequency of 2.5GHz. The receiver tolerates 0.24UIpp of high-frequency sinusoidal jitter (SJ) in this case. Without the DFE, the BER exceeds 1e−8 even when no SJ is applied.

The objective of diploma thesis is describe problems connected with designed of FTTX networks and bring the reader problems of data transmission in optical acces networks the type of PON. In the introduction are mentinoned individual technologies that already operate, and there are describe advantages disadvantages of the use topology point-to-point and point-to-multipoint. In the following chapters are dealt with problems with data broadcasting in the direction from final participant. In the other part of diploma thesis are described elements, that were used for the proposed transmission route. The own PON acces network was presented on the basis information obtained by comparing the various networks and the elements involved in them. The network presented in conclusion diploma thesis is involved in topology point to multipoint. This transmission route is simulated in the program that allows the involvement of network by the user’s need with real values. The acces network is simulated for different transmission speed and different distances. The assesment of created optical route results from the measured values, theirs source is program OptiSystem, these values are summarized in the final chapter.

Thesis deals with the analysis of the sliding contact in the ring mill. It focuses on the assessment of the effect of the current load on the sliding contact, the assessment of the signal transmission quality from the static to the rotara part of the ring contact slide contact.