No description available.

In the first chapter, a Q-switched fiber laser that is capable of generating transform-limited pulses based on single-frequency fiber laser seeded ring cavity is demonstrated. The output pulse width can be tuned from hundreds of nanoseconds to several microseconds. This Q-switched ring cavity fiber laser can operate over the whole C-band. In addition, a theoretical model is developed to numerically study the pulse characteristics, and the numerical results are in good agreements with the experimental results. In the next chapter, a Raman fiber laser is developed for generating signal at 1480 nm. Initial experimental results has demonstrated generating of Raman laser at 1175 nm, 1240 nm, 1315 nm, and 1395 nm wavelength. Finally, a free space fiber amplifier is studied both theoretically and experimentally. The experimental work has demonstrated signal coupling efficiency up to 90% in the NP highly Er/Yb co-doped phosphate fiber.

A coherent optical THz (1.5 THz, 200 µm) source was developed based on pulsed, near IR, fiber lasers, and frequency mixing in nonlinear crystals. The generated THz frequency is determined by the difference frequency of two high peak power pulsed fiber lasers at 1550 nm and 1538 nm. When incident to the crystal, the near IR lasers induce a polarization at their beat frequency which generates the THz radiation. The pulsed fiber lasers are single transverse mode, have high pulse energy and peak powers of 0.38 mJ and 128 kW respectively. They are transform limited at a few ns in duration with very good beam quality of M² ≈ 1.2. The pulse seed was created by modulating a constant laser beam with an electro-optic modulator. An arbitrary waveform generator was used to pre-shape these pulses to compensate for pulse distortion caused by pump gain depletion in the subsequent fiber amplifiers. Pre-amplifiers were constructed using commercial erbium doped silica fiber. Special, highly doped, large core, phosphate fiber was developed in-house to further amplify the pulses, while avoiding nonlinear scattering processes such as stimulated Brillouin scattering and stimulated Raman scattering. THz generation was achieved in both ZnGeP₂ and GaP which were chosen based on their low pump and THz absorption, as well as high nonlinear coefficient. Angle tuning was used to phase match all three optical frequencies in ZnGeP₂ thanks to its birefringence. Layers of GaP ~500 µm thick were pressed together alternately rotated 180° around the normal to quasi-phase match the pump and THz frequencies. To increase the efficiency of the THz generation an external optical cavity was used to enhance and recycle the IR pump pulses. The nonlinear crystal was placed inside the cavity and 151 times enhancement of THz power was observed.

Fiber tapers have attracted much attention and have been successfully employed in various applications, ranging from resonators, filters, interferometers to sensors. This thesis studies the properties of fiber tapers for the purpose of making tapered-based devices and sensors in aerospace related application where small size and light weight are critical. This thesis includes theoretical derivation and experimental verifications of distributed mode coupling in tapered single-mode fibers (SMFs) with high-resolution optical frequency-domain reflectometry (OFDR) technique. The studies are realized with OFDR through phase detection of a Mach-Zehnder interferometer (MZI), which measures local refractive index change relative to the reference arm. The wavelength shifts converted by the phase change give the group index differences between the fundamental mode and higher-order modes of fiber tapers. The energy re-distribution is observed in Rayleigh backscatter amplitude as a function of fiber length with a ~13µm resolution over the entire fiber taper, and group index difference between core and cladding modes is measured with a spatial resolution of ~2cm by using autocorrelation data processing. The thermal and mechanical properties of fiber tapers have also been characterized with OFDR. The cross-correlation wavelength shift is related to the refractive index change of the modes. It is shown that residual stress induced by the tapering process results in the inhomogeneous thermal property, which can be significantly reduced by an annealing treatment. A fiber taper with a waist diameter of ~6µm has a force sensitivity of ~620.83nm/N, ~500 times higher than that of SMF. Furthermore, polarization-preserving character of tapered polarization-maintaining fibers (PMFs) is evaluated by OFDR-based distributed birefringence along tapered PMFs. Three tapered-based micro-fiber devices have been used as effective mode selecting components to build narrow-linewidth tunable Erbium-doped fiber ring lasers. The fabrication is easy and at a low cost. 1) a tapered fiber tip forms multimode interference mechanism; 2) a two-taper MZI has been demonstrated by splitting/combining the fundamental mode and higher-order modes through fiber tapers and is tuned by bending one taper waist; 3) a novel tunable fiber Fabry-Perot filter, consisting of a hollow-core photonic bandgap fiber and a micro-fiber, is employed in the reflection mode.

This thesis focuses on research I have done on ytterbium-doped femtosecond fiber lasers. These lasers operate in the near infrared region, lasing at 1030 nm. This wavelength is particularly important in biomedical applications, which includes but is not limited to confocal microscopy and ablation for surgical incisions. Furthermore, fiber lasers are advantageous compared to solid state lasers in terms of their cost, form factor, and ease of use. Solid state lasers still dominate the market due to their comparatively high energy pulses. High energy pulse generation in fiber lasers is hindered by either optical wave breaking or by multipulsing. One of the main challenges for fiber lasers is to overcome these limitations to achieve high energy pulses. The motivation for the work done in this thesis is increasing the output pulse peak power and energy. The main idea of the work is that decreasing the nonlinearity that acts on the pulse inside the cavity will prevent optical wave breaking, and thus will generate higher energy pulses. By increasing the output energy, ytterbium-doped femtosecond fiber lasers can be competitive with solid state lasers which are used commonly in research. Although fiber lasers tend to lack the wavelength tuning ability of solid state lasers, many biomedical applications take advantage of the 1030 µm central wavelength of ytterbium-doped fiber lasers, so the major limiting factor of fiber lasers in this field is simply the output power. By increasing the output energy without resorting to external amplification, the cavity is optimized and cost can remain low and economical. During verification of the main idea, the cavity was examined for possible back-reflections and for components with narrow spectral bandwidths which may have contributed to the presence of multipulsing. Distinct cases of multipulsing, bound pulse and harmonic mode-locking, were observed and recorded as they may be of more interest in the future. The third-order dispersion contribution from the diffraction gratings inside the laser cavity was studied, as it was also considered to be an energy-limiting factor. No significant effect was found as a result of third-order dispersion; however, a region of operation was observed where two different pulse regimes were found at the same values of net cavity group velocity dispersion. Results verify the main idea and indicate that a long length of low-doped gain fiber is preferable to a shorter, more highly doped one. The low-doped fiber in an otherwise equivalent cavity allows the nonlinear phase shift to grow at a slower rate, which results in the pulse achieving a higher peak power before reaching the nonlinear phase shift threshold at which optical wave breaking occurs. For a range of net cavity group velocity dispersion values, the final result is that the low doped fiber generates pulses of approximately twice the value of energy of the highly-doped gain fiber. Two techniques of mode-locking cavities were investigated to achieve this result. The first cavity used NPE mode-locking which masked the results, and the second used a SESAM for mode-locking which gave clear results supporting the hypothesis.

Fiber tapers have attracted much attention and have been successfully employed in various applications, ranging from resonators, filters, interferometers to sensors. This thesis studies the properties of fiber tapers for the purpose of making tapered-based devices and sensors in aerospace related application where small size and light weight are critical. This thesis includes theoretical derivation and experimental verifications of distributed mode coupling in tapered single-mode fibers (SMFs) with high-resolution optical frequency-domain reflectometry (OFDR) technique. The studies are realized with OFDR through phase detection of a Mach-Zehnder interferometer (MZI), which measures local refractive index change relative to the reference arm. The wavelength shifts converted by the phase change give the group index differences between the fundamental mode and higher-order modes of fiber tapers. The energy re-distribution is observed in Rayleigh backscatter amplitude as a function of fiber length with a ~13µm resolution over the entire fiber taper, and group index difference between core and cladding modes is measured with a spatial resolution of ~2cm by using autocorrelation data processing. The thermal and mechanical properties of fiber tapers have also been characterized with OFDR. The cross-correlation wavelength shift is related to the refractive index change of the modes. It is shown that residual stress induced by the tapering process results in the inhomogeneous thermal property, which can be significantly reduced by an annealing treatment. A fiber taper with a waist diameter of ~6µm has a force sensitivity of ~620.83nm/N, ~500 times higher than that of SMF. Furthermore, polarization-preserving character of tapered polarization-maintaining fibers (PMFs) is evaluated by OFDR-based distributed birefringence along tapered PMFs. Three tapered-based micro-fiber devices have been used as effective mode selecting components to build narrow-linewidth tunable Erbium-doped fiber ring lasers. The fabrication is easy and at a low cost. 1) a tapered fiber tip forms multimode interference mechanism; 2) a two-taper MZI has been demonstrated by splitting/combining the fundamental mode and higher-order modes through fiber tapers and is tuned by bending one taper waist; 3) a novel tunable fiber Fabry-Perot filter, consisting of a hollow-core photonic bandgap fiber and a micro-fiber, is employed in the reflection mode.

This thesis focuses on research I have done on ytterbium-doped femtosecond fiber lasers. These lasers operate in the near infrared region, lasing at 1030 nm. This wavelength is particularly important in biomedical applications, which includes but is not limited to confocal microscopy and ablation for surgical incisions. Furthermore, fiber lasers are advantageous compared to solid state lasers in terms of their cost, form factor, and ease of use. Solid state lasers still dominate the market due to their comparatively high energy pulses. High energy pulse generation in fiber lasers is hindered by either optical wave breaking or by multipulsing. One of the main challenges for fiber lasers is to overcome these limitations to achieve high energy pulses. The motivation for the work done in this thesis is increasing the output pulse peak power and energy. The main idea of the work is that decreasing the nonlinearity that acts on the pulse inside the cavity will prevent optical wave breaking, and thus will generate higher energy pulses. By increasing the output energy, ytterbium-doped femtosecond fiber lasers can be competitive with solid state lasers which are used commonly in research. Although fiber lasers tend to lack the wavelength tuning ability of solid state lasers, many biomedical applications take advantage of the 1030 µm central wavelength of ytterbium-doped fiber lasers, so the major limiting factor of fiber lasers in this field is simply the output power. By increasing the output energy without resorting to external amplification, the cavity is optimized and cost can remain low and economical. During verification of the main idea, the cavity was examined for possible back-reflections and for components with narrow spectral bandwidths which may have contributed to the presence of multipulsing. Distinct cases of multipulsing, bound pulse and harmonic mode-locking, were observed and recorded as they may be of more interest in the future. The third-order dispersion contribution from the diffraction gratings inside the laser cavity was studied, as it was also considered to be an energy-limiting factor. No significant effect was found as a result of third-order dispersion; however, a region of operation was observed where two different pulse regimes were found at the same values of net cavity group velocity dispersion. Results verify the main idea and indicate that a long length of low-doped gain fiber is preferable to a shorter, more highly doped one. The low-doped fiber in an otherwise equivalent cavity allows the nonlinear phase shift to grow at a slower rate, which results in the pulse achieving a higher peak power before reaching the nonlinear phase shift threshold at which optical wave breaking occurs. For a range of net cavity group velocity dispersion values, the final result is that the low doped fiber generates pulses of approximately twice the value of energy of the highly-doped gain fiber. Two techniques of mode-locking cavities were investigated to achieve this result. The first cavity used NPE mode-locking which masked the results, and the second used a SESAM for mode-locking which gave clear results supporting the hypothesis.

The objective of the proposed research is to develop multiwavelength lasers as cost-efficient sources for broadband optical access networks. Todays telecommunications networks have widely adopted optical fiber as the backbone transmission medium. Optical fiber systems are promising candidates for the broadband access networks to offer high-speed and future-proof services. To harness the available bandwidth in fiber and to meet the ever-growing bandwidth demand, wavelength division multiplexing (WDM) techniques have been investigated. There have been intense research activities for the creation of new low-cost laser sources for such emerging applications. In this context, multiwavelength fiber ring lasers have been significantly investigated as they present many advantages, including simple structure, low-cost, and selectable multiwavelength operation. We propose a new laser system architecture that emits alternate multiwavelength picosecond pulses operating at room temperature. Optical signal generation is based on a single active component, an unbalanced Mach-Zehnder interferometer, inserted in an actively mode-locked erbium-doped fiber ring laser to provide both intensity modulation and wavelength-selective filtering. Time and frequency controls of the light emission are reached by inserting an additional modulator and a periodic filter in the cavity. This approach focuses on the application of multiwavelength lasers as sources for WDM passive optical networks.

Recently, with the escalating demands for optical communication, the need to use broadband laser light sources in optical communication network system has increased. Henceforward, the broadband characteristes of Cr4+:YAG crystal fiber possess signifies its indispensability. Furthermore, Yb3+:YAG-silica also has its advantages in high power laser domain. In this thesis, the crystal fiber grown by the laser heated pedestal growth method is used as the laser gain medium with fused silica packaging technique. Cr4+:YAG double-clad crystal fiber with a core diameter as small as 11 £gm was achieved. Moreover, a Yb3+:YAG-silica layer was formed due to the strong inter-diffusion between silica capillary and Yb3+:YAG crystal. When the silica all diffused into the Yb3+:YAG, a Yb3+:YAG-silica fiber with 125-£gm core was obtained with waveguide structure. By directly coating the optical thin films onto the end faces of the two types of fibers, the laser configuration is compact and cost effective. Besides, heat dissipation is also improved. By Cu-Al alloy packaging, a record-low Cr4+:YAG double-clad crystal fiber laser was achieved with threshold of 0.75 mW and a record-high slope efficiency of 6.9% at room temperature. And we also successfully fabricate the Yb3+:YAG-silica fiber laser with low threshold (100 mW) and high efficiency (67.2%) at room temperature. In fiber laser development, we have successfully fabricated the coating of high-reflective thin films which match the faces of fiber heterostructure (single cladding and double cladding structures). It forms a cavity with anti-reflectivity for pumping wavelength and high-reflectivity for lasing wavelength. For these reasons, low threshold, high slope efficiency, and stable laser output have been achieved. Finally, through different thin-film designs, the strain effect between thin film and heterosubstrate is significantly reduced, which facilitates the realization of high performance fiber lasers.

Fiber tapers have attracted much attention and have been successfully employed in various applications, ranging from resonators, filters, interferometers to sensors. This thesis studies the properties of fiber tapers for the purpose of making tapered-based devices and sensors in aerospace related application where small size and light weight are critical. This thesis includes theoretical derivation and experimental verifications of distributed mode coupling in tapered single-mode fibers (SMFs) with high-resolution optical frequency-domain reflectometry (OFDR) technique. The studies are realized with OFDR through phase detection of a Mach-Zehnder interferometer (MZI), which measures local refractive index change relative to the reference arm. The wavelength shifts converted by the phase change give the group index differences between the fundamental mode and higher-order modes of fiber tapers. The energy re-distribution is observed in Rayleigh backscatter amplitude as a function of fiber length with a ~13µm resolution over the entire fiber taper, and group index difference between core and cladding modes is measured with a spatial resolution of ~2cm by using autocorrelation data processing. The thermal and mechanical properties of fiber tapers have also been characterized with OFDR. The cross-correlation wavelength shift is related to the refractive index change of the modes. It is shown that residual stress induced by the tapering process results in the inhomogeneous thermal property, which can be significantly reduced by an annealing treatment. A fiber taper with a waist diameter of ~6µm has a force sensitivity of ~620.83nm/N, ~500 times higher than that of SMF. Furthermore, polarization-preserving character of tapered polarization-maintaining fibers (PMFs) is evaluated by OFDR-based distributed birefringence along tapered PMFs. Three tapered-based micro-fiber devices have been used as effective mode selecting components to build narrow-linewidth tunable Erbium-doped fiber ring lasers. The fabrication is easy and at a low cost. 1) a tapered fiber tip forms multimode interference mechanism; 2) a two-taper MZI has been demonstrated by splitting/combining the fundamental mode and higher-order modes through fiber tapers and is tuned by bending one taper waist; 3) a novel tunable fiber Fabry-Perot filter, consisting of a hollow-core photonic bandgap fiber and a micro-fiber, is employed in the reflection mode.