This thesis describes the deposition of thin films of titanium oxide and Magnéli phases of titanium oxide by atomic layer deposition (ALD) using a novel β-ketoesterate precursor. Titanium oxide is a promising candidate for the high-k dielectric gate oxide layer for CMOS devices in microelectronic circuits. The Magnéli phases of titanium oxide are difficult to grow and stabilize, especially in the thin film form, and have useful properties. The thin film deposition of oxides by CVD/ALD requires suitable precursors, which are often metalorganic complexes. The estimation of vapour pressure using thermogravimetry is described, and employed, using an approach based on the Langmuir equation. This data is important for the evaluation of the suitability of these complexes as CVD precursors. The first chapter gives a brief introduction to the topics that will be discussed in this thesis. Part one of the thesis deals with the synthesis, characterization, and studies of the vapour pressure and partial pressures of the precursors for CVD. This part comprises of the second, third and fourth chapter. The second chapter deals with the synthesis and characterization of the various metalorganic complexes that have been synthesized and characterized to evaluate their suitability as precursors for CVD. The third chapter describes the derivation of vapour pressure of precursors for CVD and ALD, from rising temperature thermogravimetric analysis (TGA) data, using the Langmuir equation. The fourth chapter deals with the determination of partial pressure of CVD precursors using data from low-pressure thermogravimetry. Part Two of the thesis reports the deposition of titanium oxide thin films by ALD, and the detailed investigation of their properties, for application as high-k dielectric materials. Chapters five, six and seven constitute this part. The fifth chapter deals with the deposition of titanium oxide thin films by ALD. Chapter six describes the electrical characterization of the thin films of titanium oxide, for applications as high-k dielectric gate oxide layers for CMOS circuits. In the seventh chapter, the deposition of Magnéli phases of titanium by ALD is described. The dielectric properties of the films are studied.

All solid state Li-ion batteries (thin film micro batteries) have become inevitable for miniaturized devices and sensors as power sources. Fabrication of electrode materials for batteries in thin film form has been carried out with the existing technologies used in semiconductor industry. In the present thesis, radio frequency (RF) sputtering has been chosen for deposition of cathode material (ceramic oxides) thin films because of several advantages such as precise thickness control and deposition of compound thin films with equivalent composition. Conventional sputtering involves fabrication of thin film using custom made pellet according to the specification of sputter gun. However several issues such as target breaking are inevitable with the pellet sputtering. To forfend the issues, powder sputtering has been implemented for the deposition of various thin film cathodes in an economically feasible approach. Optimization of various process parameters during film deposition of cathode materials LiCoO2, Li2MnO3, LiNixMnyO4, mixed oxide cathodes of LiMn2O4, LiCoO2 and TiO2 etc., have been executed successfully by the present approach to achieve optimum electrochemical performance. Thereafter the optimized process parameters would be useful for selection of cathode layers for micro battery fabrication. Chapter 1 gives a brief introduction to the Li ion and thin film solid state batteries. It also highlights the advantages of powder sputtering compared to conventional pellet sputtering. In Chapter 2, the materials used and methods employed for the fabrication of thin film electrodes and analytical characterizations have been discussed. In chapter 3, implementation of powder sputtering for the deposition of LiCoO2 thin films has been discussed. X-Ray diffraction (XRD), X-Ray photoelectron spectroscopy (XPS) and electrochemical investigations have been carried out and promising results have been achieved. Charge discharge studies delivered a discharge capacity of 64 µAh µm-1 cm-2 in the first cycle in the potential range 3.0-4.2 V vs. Li/Li+. The possible causes for the moderate cycle life performance have been discussed. Systematic investigations for RF power optimization for the deposition of Li2-xMnO3-y thin films have been carried out. Galvanostatic charge discharge studies delivered a highest discharge capacity of 139 µAh µm-1cm-2 in the potential window 2.0-3.5 V. Thereafter, effect of LMO film thickness on electrochemical performance has been studied in the thickness range 70 nm to 300 nm. Films of lower thickness delivered higher discharge capacity with good cycle life than the thicker films. These details are discussed in chapter 4. In Chapter 5, fabrication and electrochemical performance of LiNixMnyO4 thin films are presented. LMO thin films have been deposited on nickel coated stainless steel substrates. The as deposited films were annealed at 500 °C in ambient conditions. Nickel diffuses in to LMO film and results in LiNixMnyO4 (LMNO) film. These films were further characterized. Electrochemical studies were conducted up to higher potential 4.4 V resulted in discharge capacities of the order of 55 µAh µm-1cm-2. In chapter 6, electrochemical investigations of mixed oxide thin films of LiCoO2 and LiMn2O4 have been carried out. Electrochemical investigations have been carried out in the potential window 2.0–4.3 V and a discharge capacity of 24 µAh µm-1cm-2 has been achieved. In continuation, TiO2 powder was added to the former composition and the deposited films were characterized for electrochemical performance. The potential window as well as the discharge capacity enhanced after TiO2 doping. Electrochemical characterization has been carried out in the potential window 1.4–4.5 V, and a discharge capacity of 135 µAh µm-1cm-2 has been achieved. Finally chapter 7 gives overall conclusions and future directions to the continuation of the work.

Metal Oxide (MO)semiconductors are one of the most widely used materials in commercial gas sensor devices. The basic principle of chemoresistive gas sensor operation stems on the high sensitivity of electrical resistance to ambient gaseous conditions. Depending on whether the oxide is "p type" or "n type", the resistance increases (or decrease), when placed in atmosphere containing reducing (or oxidizing) gases. The study of conductometric metal oxide semiconductor gas sensors has dual importance in view of their technological device applications and understanding fundamental MO-gas interactions. Metal oxides based sensors offer high thermal, mechanical and chemical stability. A large number of MOs show good sensitivities to various gases like CO, NOX, SOX, NH3, alcohols and other Volatile Organic Compounds (VOCs). VOCs are very common hazardous pollutants in the environment. Gas sensors are in great demand for their various applications such as food quality control, fermentation industries, road safety, defence, environmental monitoring and other chemical industries. The aim of the study is to explore the possibility of advancements in semiconducting MO based gas sensor devices through tuning microstructural parameters along with chemical dopants or additives. And further to investigate the underlying mechanism of conductometric MO gas sensors. The novel synthesis method employed is based on the solution combustion method coupled with ultrasonically nebulized spray pyrolysis technique. The well studied SnO2 and relatively unexplored Cr2O3 oxide systems are selected for the study. The non-equilibrium processing conditions result in unique microstructure and defect chemistry. In addition, using this technique MO - Reduced Graphene Oxide (RGO) nanocomposite films has also been fabricated and its application to room temperature gas sensor devices is demonstrated. The thesis comprises of seven chapters. the following section describe the summery of individual chapters. The Chapter 1 describes the introduction and background literature of this technology. A brief review of developments in gas sensor technology so far has been enlisted. This chapter also gives a glimpse of applications of MO semiconductors based sensors. The underlying mechanism involved in the sensing reaction and the primary factors influencing the response of a gas sensor device are enlisted. Further in the later part of the chapter focused the material selection criteria, effect of additives/dopants and future prospects of the technology. The end of this chapter highlights the objective and scope of the work in this dissertation. In the Chapter 2 the the materials selection, characterization techniques and particularly the experimental setups used are elaborated. This includes the deposition method used, which is developed in our group and the the in house built gas sensing system including its working principles and various issues have been addressed. The Ultrasonic Nebulized Spray Pyrolysis of Aqueous Combustion Mixture (UNSPACM) is a novel deposition method devised, which is a combination of conventional spray pyrolysis and solution combustion technique. Spray pyrolysis is versatile, economic and simple technique, which can be used for large area deposition of porous films. The intention is to exploit the exothermicity of combustion reaction in order to have high crystallinity, smaller crystallite size with high surface area, which are extremely important in gas sensor design and its efficiency. Further the gas sensing system and its operation are discussed in detail including the advantages of vertical sensing chamber geometry, wider analyte concentration range (ppm to percentage) obtained through vapor pressure data and simultaneous multi sensor characterization allowing better comparison. Here in this work, Chromium oxide (Cr2O3) and Tin oxide (SnO2) are selected as gas sensing materials for this work as a p-type and n-type metal oxide semiconductors respectively. Nevertheless Cr2O3 is a less explored gas sensing material as compared to SnO2, which is also being used in many commercially available gas sensor devices. Thus, studying and comparing gas sensing properties of a relatively novel and a well established material would justify the potential of the novel deposition technique developed. In Chapter 3, the effect of exothermic reaction between oxidizer and fuel, on the morphology, surface stoichiometry and observed gas sensing properties of Cr2O3 thin films deposited by UNSPACM, is studied. An elaborative study on the structural, morphological and surface stoichiometry of chromium oxide films is undertaken. Various deposition parameters have been optimized. An extensive and systematic gas sensing study is carried out on Cr2O3 films deposited, to achieve unique microstructure. The crystallinity and microstructure are investigated by varying the deposition conditions. Further, the effect of annealing in oxygen gas atmospheres on the films was also investigated. The gas sensing properties are studied for various VOCs, in temperature range 200 - 375 oC. The possible sensing mechanism and surface chemical processes involved in ethanol sensing, based on empirical results, are discussed. In chapter 4, the effect of 1% Pt doping on gas sensing properties of Cr2O3 thin films prepared by UNSPACM, is investigated. The chemical analysis is done using x-ray photoelectron spectroscopy to find the chemical state of Pt and quantification is done. The gas sensing is done towards gases like NO2, Methane and Ethanol. The enhancement in sensitivity and remarkable reduction in response as well as recovery times have been modeled with kinetic response analysis to study the variation with temperature as well as concentration. Further the analysis of observations and model fittings is discussed. The Chapter 5 deals with the defects induced ferromagnetism and gas sensing studies SnO2 nanoparticles prepared by solution combustion method. The structural, chemical analysis of as-synthesized and annealed SnO2 nanoparticles reveal gradual reduction in defect concentration of as-prepared SnO2. The findings of various characterization techniques along with optical absorption and magnetic studies to investigate the defect structure of the material are presented. As defects play crucial role in gas sensing properties of the metal oxide material, the defect induced room temperature ferromagnetism in undoped SnO2 has been used as a potential tool to probe the evidence of the defects. Finally a correlation is established between observed room temperature ferromagnetism and gas sensing studies and primary role of defects in gas sensing mechanism over microstructure is realized . The Chapter 6 presents the deposition of SnO2 thin films by UNSPACM method on glass substrates for gas sensing application. The readiness of UNSPACM in making sensor materials with unform dopant distribution is demonstrated in order to improve the sensor performance in terms of response and selectivity. The chemical composition, film morphology and gas sensing studies are reported. The SnO2 is doped with Cr and Pt to enhance the sensing properties of the material. The doped Oxide films are found to show enhancement in sensitivity and improve the selectivity of the films towards specific gases like NO2 and CO. Further in Chapter 7 an effort has been made to overcome the problem of high operating temperature of metal oxide gas sensors through use of Reduced Graphene Oxide (RGO) and metal oxide nanocomposite films. Although RGO shows room temperature response towards many toxic and hazardous gases but it exhibits poor sensor signal recovery. This has been successfully solved by making nanohybrids of RGO and SnO2. It not only improves the sensor signal kinetics but it enhances the sensitivity also. Thus this chapter endeavors towards low power consumption gas sensing devices. The key findings and future aspects are summarized in the Chapter 8.

Spintronics (spin based electronics) is a relatively new topic of research which is important both from the fundamental and technological point of view. In conventional electronics charge of the electron is manipulated and controlled to realize electronic devices. Spintronics uses charge as well as the spin degree of freedom of electrons, which is completely ignored in the charge based devices. This new device concept brings in a whole new set of device possibilities with potential advantages like higher speed, greater efficiency, non-volatility, reduced power consumption etc. The first realization of the spintronic device happened in 1989, owing to the discovery of the Giant Magneto-resistive (GMR) structure showing a large resistance change by the application of an external magnetic field. Nobel Prize in Physics is awarded for this discovery in 2007. In less than ten years, such devices moved from the lab to commercial devices, as read head sensors in hard disc drives. This new sensor led to an unprecedented yearly growth in the area l density of bits in a magnetic disc drive. Since 2005, another spintronic device known as Magnetic Tunnel Junction (MTJ) which shows a better performance replaced the existing GMR structures in the read heads. Another device which can potentially replace Si based Dynamic Random Access Memory (DRAM) is Magneto-resistive Random Access Memory (MRAM). Being magnetic it is non-volatile, which means not only it retains its memory with the power turned off but also there is no constant power required for frequent refreshing. This can save a lot of power(~ 10-15 Watts in a DRAM), which is quite significant amount for any portable device which runs under battery. Prototype of a commercial MRAM is also made during 2004-2005 by Infineon and Freescale Semiconductors. Recent development has shown switching of magnetic moment by spin-polarised currents (known as spin transfer torque), electric fields, and photonic fields. Instead of Oersted field switching in the conventional MRAM devices, spin torque effect can also be used to switch a magnetic element more efficiently. Recently Spin-Torque MRAM has gained lot of interest due to it’s less power consumption during the writing process. A continuous research effort is going on in realizing other proposed spintronic devices, such as Spin Torque Oscillator, Spin Field Effect Transistor , Race Track Memory etc. which are yet to get realized or yet to make their entry in the commercial devices. Spintronics can be divided in to two broad subfields viz.(1) Semiconductor Spintronics and (2) Metallic Spintronics. Most of the devices belong to the second class whereas the former one is rich in fundamental science and not yet cleared its path towards the world of application. Any spintronic device requires ferromagnetic material which is generally the source of spin polarized electrons. For semiconductor spintronic devices, the main obstacle is the non-existence of the ferromagnetic semiconductor above room temperature (RT). So the development in this direction is very much dependent on the material science research and discovery of novel material systems. Almost a decade back, Dilute Magnetic Semiconductors (DMS) are proposed to behaving RT ferromagnetism. As a result an intense theoretical and experimental research is being carried out since then on these materials. Still a general consensus is lacking both in terms of theory as well as experiment. There are many methodologies and thin film deposition protocols have been followed by different research groups to realize spintronic device concepts. The deposition techniques such as magnetron sputtering, molecular beam epitaxy have been found very efficient for growing metallic spintronic devices. For semiconductor spintronics especially in the area of Dilute Magnetic Semiconductors (DMS) pulsed laser ablation is also considered to be a viable technique. Even though pulsed laser ablation is a very powerful technique to prepare stoichiometric multi-component oxide films, it’s viability for the growth of metallic films and multilayer is considered to be limited. In this regard, we have used pulsed laser ablation to prepare pure and Co doped ZnO films, to examine the magnetic and magneto-transport behavior of these oxides. In addition extensive work has been carried out to optimize and reproducibly prepare metallic multilayer by Pulsed Laser Deposition to realize Spin Valve (SV) effect, which proves the viability of this technique for making metallic multilayer. This thesis deals with the study of Pulsed Laser Deposition(PLD) deposited DMSs and metallic SVs. The thesis is organized into seven chapters as described below: • Chapter:1 This chapter gives an introduction to Spintronics and the different device structures. It is followed by a brief description of the motivation of the present work. Since magnetism is at the heart of the spintronics, next we attempt to introduce some of the basic concepts in magnetism, which are related to the topics discussed in the following chapters. We discuss about various exchange interactions responsible for the long range ferromagnetic ordering below Curie temperature in different compounds. Other magnetic properties are also discussed. Then another important phenomenon called magnetic anisotropy is brought in. We discuss the origin of different types of anisotropy in materials. These anisotropies are also responsible for magnetic domain formation. Then a description of the different types of domain walls are introduced. Unlike conventional electronics, spintronics deals with spin polarized current. A short description of spin polarization from the band picture and concept of half-metal is introduced. The next part (Section-I) of this chapter gives an overview of the challenges in semiconductor spintronics. The spin injection efficiency from a ferromagnetic metal to a semiconductor is found to be poor. This problem is attributed to the conductivity mismatch at the interface. DMS materials can be potential candidates in order to solve this problem. Ferromagnetism in these proposed materials cannot be explained in terms of the standard exchange mechanisms. A model was first proposed for the hole doped system based on Zener model. A more apt model for the n-doped high dielectric materials is then proposed based on Bound Magnetic Polarons (BMP). These models for the unusual ferromagnetism are briefly discussed. Although ferromagnetism is observed by different groups, often questions are raised about the intrinsic origin of this behavior and the topic is still under debate. In this study we have tried to correlate the magnetic property with the transport property as the transport properties are generally not affected much by the presence of external impurities and probes the intrinsic property of the material. Transport and the magneto-transport in disordered materials in general are discussed. A specific model proposed for degenerate semiconductors, which is used for fitting our experimental data is explained. As the ferromagnetism in these materials are generally found to be related to the defects, different types of possible defects are described. Section-II deals with the metallic SV devices. In the history of spintronics, this is one of the most basic and most studied structures, but still having a lot of interest both fundamentally and technologically. A brief history of this discovery and a chronological progress in the device structure is discussed. Our work focuses on the metallic spin valve (SV) structures. Different types of SVs and their properties are explained. In a SV structure one of the ferromagnets (FM) is pinned using an adjuscent antiferromagnetic layer by an effect called exchange bias. A brief description of exchange bias and the effects of different parameters is given. This is followed by a discussion about the theory of GMR which deals with the spin dependent scattering at the bulk and at the interfaces, their relative contributions, effect of the band matching etc. A simple resistor model is used to explain the qualitative behavior of these SVs. The chapter is concluded with a brief summery and applications. • Chapter:2 This chapter provides a brief description of some of the experimental apparatus that are used to perform various experiments. The chapter is organized according to the general functionality of the techniques. This includes different thin film deposition techniques which are used depending on the requirements and also for comparing the properties of the samples, grown by different techniques. Structural, spectroscopic, magnetic and different microscopy techniques which are extensively used throughout, are discussed and their working principles are explained. This work also involves nano/microstructuring of devices. Mainly two structuring techniques are used viz. e-beam lithography and optical lithography by laser writer. In this section we will be discussing about these two techniques and other associated techniques like lift-off, etching etc. Effect of different parameters on the device structures are highlighted. • Chapter:3 Chapter-3 deals with the synthesis and characterization of the pure and 5% Co doped ZnO bulk samples. First a brief introduction about the ZnO crystal structure, band structure and other properties are given followed by the synthesis technique followed in our study. Synthesis is done by low temeperature in organic co-precipitation method. This liquid phase synthesis gives better homogeniety. As-grown sample is also sintered at a higher temperature. Structural study confirms the proper synthesis of the intended compound. Spectroscopic as well as magnetic study of the bulk doped sample indicates the presence of Co nano clusters in the low temperature synthesized sample, whereas after sintering indication of Co2+ is observed which reflects in the magnetic property as well. These samples are used as target material for laser ablation. • Chapter:4 Chapter-4 presents the results of the pure and Co doped ZnO thin film samples. Thin films are grown by PLD method on r-plane Sapphire substrates. Details of the growth technique and the deposition parameters are explained. Our result shows that 5% Co doped ZnO thin film is ferromagnetic in nature as expected in a DMS material, although the film is grown using a paramagnetic target. We also report that pure ZnO grown in an oxygen deficient condition giving ferromagnetic behavior. Not only that, the obtained saturation moment is much higher compared to the Co doped sample. We have demonstrated that the FM can be tuned by tuning the oxygen content and FM disappears when the film is annealed in an oxygen environment .But for the Co doped sample magnetic property could not be tuned much as Co doping stabilizes the surface states. To exclude the possibilities of the extrinsic origin we have done a detailed magneto-transport study for both doped and undoped films. For ZnO, we have shown a one to one correlation of the magnetic and magneto-transport data which further supports the fact that the obtained magnetic behavior is intrinsic. Fitting of the magnetorsistance (MR) data for the pure and Co doped ZnO samples is done using a semi-empirical formula, consisting of both positive and negative MR terms originally proposed for degenerate semiconductors .Excellent agreement of the experimental data is found with the formula. For pure ZnO sample we have extracted the mobility, carrier concentration etc .by Hall measurement. The fabrication steps of Hall bar sample which involves optical lithography and ion beam etching are discussed. 3D e-e interaction induced transport mechanism is found to be dominant in case of oxygen deficient pure ZnO. • Chapter:5 Chapter-5 demonstrates the tuning of band gap of ZnO by alloying with MgO. By changing the ZnO:MgO ratio in PLD grown films, we could tune the band gap over a wide range. Composition alanalysis is done by Rutherford Back-Scattering. Structural and spectroscopic studies are carried out, which shows tuning of band gap upon alloying with MgO. We could tune ZnO band gap from 3.3eV to 3.92eV by30% MgO alloying, while retaining the Wurtzite crystal structure. • Chapter:6 Chapter-6 demonstrates the metallic Pseudo Spin Valve (PSV) structures grown by sputtering and by PLD. Main focus of this chapter is to show that, PLD can be aviable technique for making metallic PSV and Spin Valve (SV) structures. This is almost an unexplored technique for growing metallic thin film SVs, as it is evident in the literature. NiFe and Co are used as the soft and hard FM layers respectively, Au and Cu are used as the spacer layer. FeMn is used for pinning the Co layer in case of the SV structures. The first section describes the properties of these materials and then substrate preparation, deposition parameters etc. are explained in details. Properties of sputter deposited PSV structures are also described. Thickness variation of different layers, double PSV structure and angular variation of the MR properties are presented. Generally two measurement geometries are followed for the SV measurements viz.(1) Current In Plane (CIP) and (2) Current Perpendicular to Plane(CPP). We have carried out MR studies in both the measurement geometries. Measurement in CPP geometry is much more involved than CIP and need structuring with multiple lithography steps. CPP measurement geometry scheme and the process steps are discussed. For this measurement a special ac bridge technique is followed which is also discussed. In the next part we have demonstrated PSV and SV structures, grown, using PLD in an Ultra High Vacuum (UHV) system. Not only that, we have obtained a CIPMR as high as 3.3%. PLD is generally thought to be a technique for oxide deposition and metallic multilayers are not deposited due to particulate formation, high enegy of the adatom species which can lead to inter-mixing at the interface etc. But in this study we have shown that by properly tuning the deposition parameters, it is possible to grow SVs using PLD. We have found the roughness of the PLD grown films are much lower compared to the sputtered films. For top SV structures we have obtained exchange bias even in the absence of applied field during deposition. This effect is observed by performing magnetic and magneto-resistance measurements. Effect of different layer thicknesses, field annealing etc. are discussed. Two different spacer layers are used and their properties are compared. We have found that the interface engineered structures are giving highest MR among the different samples. Then a conclusion of our study is presented followed by a discussion on the difficulties and challenges faced for optimizing the PLD grown SVs. • Chapter:7 Finally, in Chapter-7, various results are summarized and a broad outlook is given. Perspectives for the continuation of the present work is also given.

Recently, there has been a growing interest in semiconductor and semiconducting oxide nanowires for applications in electronics, energy conversion, energy storage and optoelectronic devices such as field effect transistors, solar cells, Li- ion batteries, gas sensors, light emitting diodes, field emission displays etc. Semiconductor and semiconducting oxide nanowires have been synthesized widely by different vapor transport methods. However, conditions like high growth temperature, low vacuum, carrier gases for the growth of nanowires, limit the applicability of the processes for the growth of nanowires on a large scale for different applications. In this thesis work, studies have been made on the growth of semiconductor and semiconducting oxide nanowires at a relatively lower substrate temperature (< 500 °C), in a high vacuum (1× 10-5 mbar), without employing any carrier gas, by electron beam and resistive thermal evaporation processes. The morphology, microstructure, and composition of the nanowires have been investigated using analytical techniques such as SEM, EDX, XRD, XPS, and TEM. The optical properties of the films such as reflectance, transmittance in the UV-visible and near IR region were studied using a spectrophotometer. Germanium nanowires were grown at a relatively lower substrate temperature of 380-450 °C on Si substrates by electron beam evaporation (EBE) process using a Au-assisted Vapor-Liquid-Solid mechanism. High purity Ge was evaporated in a high vacuum of 1× 10-5 mbar, and gold catalyst coated substrates maintained at a temperature of 380-450 °C resulted in the growth of germanium nanowires via Au-catalyzed VLS growth. The influence of deposition parameters such as the growth temperature, Ge evaporation rate, growth duration, and gold catalyst layer thickness has been investigated. The structural, morphological and compositional studies have shown that the grown nanowires were single-crystalline in nature and free from impurities. The growth mechanism of Germanium nanowires by EBE has been discussed. Studies were also made on Silicon nanowire growth with Indium and Bismuth as catalysts by electron beam evaporation. For the first time, silicon nanowires were grown with alternative catalysts by the e-beam evaporation method. The use of alternative catalysts such as Indium and Bismuth results in the decrease of nanowire growth temperature compared to Au catalyzed Si nanowire growth. The doping of the silicon nanowires is possible with an alternative catalyst. The second part of the thesis concerns the growth of oxide semiconductors such as SnO2, Sn doped Indium oxide (ITO) nanowires by the electron beam evaporation method. For the first time, SnO2 nanowires were grown with a Au-assisted VLS mechanism by the electron beam evaporation method at a low substrate temperature of 450 °C. SEM, XRD, XPS, TEM, EDS studies on the grown nanowires showed that they were single crystalline in nature and free of impurities. The influence of deposition parameters such as the growth temperature, oxygen partial pressure, evaporation rate of Sn, and the growth duration has been investigated. Studies were also done on the application of SnO2 nanowire films for UV light detection. ITO nanowires were grown via a self-catalytic VLS growth mechanism by electron beam evaporation without the use of any catalyst at a low substrate temperature of 250-400 °C. The influence of deposition parameters such as the growth temperature, oxygen partial pressure, evaporation rate of ITO, and growth duration has been investigated. Preliminary studies have been done on the application of ITO nanowire films for transparent conducting coatings as well as for antireflection coatings. The final part of the work is on the Au-assisted and self catalytic growth of SnO2 and In2O3 nanowires on Si substrates by resistive thermal evaporation. For the first time, SnO2 nanowires were grown with a Au-assisted VLS mechanism by the resistive thermal evaporation method at a low substrate temperature of 450 °C. SEM, XRD, XPS, TEM, and EDS studies on the grown nanowires showed that they were single crystalline in nature and free of impurities. Studies were also made on the application of SnO2 nanowire films for methanol sensing. The self-catalytic growth of SnO2 and In2O3 nanowires were deposited in high vacuum (5×10-5 mbar) by thermal evaporation using a modified evaporation source and a substrate arrangement. With this arrangement, branched SnO2 and In2O3 nanowires were grown on a Si substrate. The influence of deposition parameters such as the applied current to the evaporation boat, and oxygen partial pressure has been investigated. The growth mechanism behind the formation of the branched nanowires as well as nanowires has been explained on the basis of a self-catalytic vapor-liquid-solid growth mechanism. The highlight of this thesis work is employing e-beam evaporation and resistive thermal evaporation methods for nanowire growth at low substrate temperatures of ~ 300-500 °C. The grown nanowires were tested for applications such as gas sensing, transparent conducting coatings, UV light detection and antireflection coating etc. The thesis is divided into nine chapters and each of its content is briefly described below. Chapter 1 In this chapter, a brief introduction is given on nanomaterials and their applications. This chapter also gives an overview of the different techniques and different growth mechanisms used for nanowires growth. A brief overview of the applications of semiconductors and semiconductor oxide nanowires synthesized is also presented. Chapter 2 Different experimental techniques employed for the growth of Si, Ge, SnO2, In2O3, ITO nanowires have been described in detail in this chapter. Further, the details of the different techniques employed for the characterization of the grown nanowires were also presented. Chapter 3 In this chapter, studies on the growth of Germanium nanowires by electron beam evaporation (EBE) are given. The influence of deposition parameters such as growth temperature, evaporation rate of germanium, growth duration, and catalyst layer thickness was investigated. The morphology, structure, and composition of the nanowires were investigated by XRD, SEM, and TEM. The VLS growth mechanism has been discussed for the formation of the germanium nanowires by EBE using Au as a catalyst. Chapter 4 This chapter discusses the growth of Si nanowires with Indium and Bismuth as an alternate to Au-catalyst by electron beam evaporation. The influence of deposition parameters such as growth temperature, Si evaporation rate, growth duration, and catalyst layer thickness has been investigated. The grown nanowires were characterized using XRD, SEM, TEM and HRTEM. The Silicon nanowires growth mechanism has been discussed. Chapter 5 This chapter discusses the Au-catalyzed VLS growth of SnO2 nanowires by the electron beam evaporation method as well as Antimony doped SnO2 nanowires by co-evaporation method at a low substrate temperature of 450 °C. The grown nanowires were characterized using XRD, SEM, TEM, STEM, Elemental mapping, HRTEM, and XPS. The effect of deposition parameters such as oxygen partial pressure, growth temperature, catalyst layer thickness, evaporation rate of Sn, and the growth duration of nanowires were investigated. The SnO2 nanowires growth mechanism has been explained. Preliminary studies were made on the possible use of pure SnO2 and doped SnO2 nanowire films for UV light detection. SnO2 nanowire growth on different substrates such as stainless steel foil (SS), carbon nanosheets films, and graphene oxide films were studied. SnO2 nanowire growth on different substrates, especially SS foil will be useful for Li-ion battery applications. Chapter 6 This chapter discusses the self catalyzed VLS growth of Sn doped Indium oxide (ITO) nanowires by the electron beam evaporation method at a low temperature of 250-400 °C. The grown nanowires were characterized using XRD, SEM, TEM, STEM, HRTEM, and XPS. The effect of deposition parameters such as oxygen partial pressure, growth temperature, evaporation rate of ITO, and the growth duration of the nanowires were investigated. Preliminary studies were also made on the possible use of self-catalyzed ITO nanowire films for transparent conducting oxides and antireflection coatings. ITO nanowire growth on different and large area substrates such as stainless steel foil (SS), and Glass was done successfully. ITO nanowire growth on different substrates, especially large area glass substrates will be useful for optoelectronic devices. Chapter 7 In this chapter, studies on the growth of SnO2 nanowires by a cost-effective resistive thermal evaporation method at a relatively lower substrate temperature of 450 °C are presented. The grown nanowires were characterized using XRD, SEM, TEM, HRTEM, and XPS. Preliminary studies were done on the possible use of SnO2 nanowire films for methanol sensing. Chapter 8 This chapter discusses the self-catalytic growth of SnO2 and In2O3 nanowires by resistive thermal evaporation. The nanowires of SnO2 and In2O3 were grown at low temperatures by resistive thermal evaporation using a modified source and substrate arrangement. In this arrangement, branched SnO2 nanowires, and In2O3 nanowires growth was observed. The grown nanowires were characterized using XRD, SEM, TEM, HRTEM, and XPS. The possible growth mechanism for branched nanowires growth has been explained. Chapter 9 The significant results obtained in the present thesis work have been summarized in this chapter.

Man’s desire to replicate/mimic the nature’s creation provided an impetus and inspiration to the rapid advancements and progress made in the sensors and actuators technology. A normal human being has five basic sensory organs, which helps and guides him in performing the routine tasks. This underlines the importance of basic sensory organs in a human life. In a similar fashion, sensors and actuators are of paramount importance for most of the science and engineering applications. The aim of the present thesis work is to explore the application of piezoelectric ZnO thin films deposited on a flexible substrate for the development of sensors and actuators. Detailed study was performed on the suitability of three different flexible substrates namely Phynox, Kapton and Mylar. However, Phynox alloy substrate was found to be a suitable substrate material for the above mentioned applications. Sputtering technique was chosen for the deposition of ZnO thin films on to Phynox substrate. The necessary process parameters were optimized to achieve good quality piezoelectric thin films. In the present work, sensors have been developed by utilizing the direct piezoelectric effect of ZnO thin films deposited on Phynox alloy substrate. These includes a flow sensor for gas flow rate measurement, impact sensor for non-destructive material discrimination study and a Thin Film Sensor Array (TFSA) for monitoring the impact events. On the other hand, using the converse piezoelectric effect of ZnO thin films, actuators have also been developed. These include a thin film micro actuator and a Thin Film Micro Vibrator (TFMV) for vibration testing of micro devices. The thesis is divided into following seven chapters. Chapter 1: This chapter gives a general introduction about sensors and actuators, piezoelectric thin films, flexible substrates, thin film deposition processes and characterization techniques. A brief literature survey of different applications of piezoelectric thin films deposited on various flexible substrates in device development is presented. Chapter 2: A novel flexible metal alloy (Phynox) and its properties along with its applications are discussed in this chapter. ZnO thin films were deposited on Phynox substrate by Rf reactive magnetron sputtering technique. The sputtering process parameters such as: Ar:O2 gas ratio, substrate temperature and RF power were optimized for the deposition of good quality piezoelectric ZnO thin films. The deposited ZnO thin films were characterized using XRD, SEM, AFM and d31 coefficient measurement techniques. Chapter 3: It reports on the comparative study of properties of piezoelectric ZnO thin films deposited on three different types of flexible substrates. The substrate materials employed were a metal alloy (Phynox), polyimide (Kapton), and polyester (Mylar). Piezoelectric ZnO thin films deposited on these flexible substrates were characterized by XRD, SEM, AFM and d31 coefficient measurement techniques. A vibration sensing test was also performed for the confirmation of good piezoelectric property. Compared to the polymer flexible substrates, the metal alloy flexible substrate (Phynox) was found to be more suitable for integrating ZnO thin film for sensing applications. Chapter 4: The development of a novel gas flow sensor for the flow rate measurement in the range of L min-1 is presented in this chapter. The sensing element is a Phynox alloy cantilever integrated with piezoelectric ZnO thin film. A detailed theoretical analysis of the experimental set–up showing the relationship between output voltage generated and force at a particular flow rate has been discussed. The flow sensor is calibrated using an in-house developed testing set-up. Chapter 5: This chapter is divided into two sections. Section 5.1 reports on the development of a novel packaged piezoelectric thin film impact sensor and its application in non-destructive material discrimination studies. Different materials (Iron, Glass, Wood and Plastic) were successfully discriminated by using the developed impact sensor. The output response of impact sensor showed good linearity and repeatability. The impact sensor is sensitive, reliable and cost-effective. Section 5.2 reports on the development of a Thin Film Senor Array (TFSA) for monitoring the location and magnitude of the impact force. The fabricated TFSA consists of evenly distributed ZnO thin film sensor array. Chapter 6: It consists of two sections. Section 6.1 reports on the fabrication of micro actuator using piezoelectric ZnO thin film integrated with flexible Phynox substrate. A suitable concave Perspex mounting was designed for the actuator element. The actuator element was excited at different frequencies for the supply voltages of 2V, 5V and 8V. The developed micro actuator has the potential to be used as a micro pump for pumping nano liters to micro liters of fluids. Section 6.2 reports the design and development of a portable ready to use Thin Film Micro Vibrator (TFMV). The TFMV is capable of providing the vibration amplitude in the range of nanometer to micrometer. A thin silicon diaphragm was used as a test specimen for its vibration testing studies using the developed TFMV. The TFMV is light-weight and have internal battery, hence no external power supply is required for its functioning. Chapter 7: The first section summarizes the salient features of the work presented in this thesis. In the second section the scope for carrying out the further work is given.

No description available.

No description available.

Two technologies, namely Laser Technology and Surface Modification Technology, have made rapid strides in the last few decades. The lasers have evolved from a simple laboratory curiosity to a matured industrial tool and its applications are limited only by imagination. Intense, coherent and monochromatic laser sources with power outputs ranging over several orders of magnitude have found innumerable applications in the realm of materials engineering. Reactive Pulsed Laser Deposition (PLD) is a powerful technique that utilises the power of a nanosecond pulsed laser for materials synthesis. Unlike conventional PLD, which require high density targets that are difficult to synthesize at a reasonable cost, the RPLD circumvents the need for one such ceramic target. This thesis presents a detailed and judicious use of this technique for synthesis of hard ceramic multilayer coatings using elemental metal targets. Transition metal nitrides having rock salt structure are known to exhibit superior properties such as hardness and wear resistance and hence formed the basis for the development of first generation coatings. Further improvements through alloying of these binary compounds with metal or metalloid components lead to the development of second generation coatings. As the demand for functional materials increased, surface modification technology alias surface engineering, grew in leaps and bounds. As the large number of coating requirements for optimal performance could not be fulfilled by a single homogeneous material, third generation coatings, comprising multilayer coatings, were developed. It is this aspect of combining the advantages of RPLD process to synthesize ceramic multilayer coatings, provides the main motivation for the present research work. In this thesis, a systematic study presented for synthesis of nanocrystalline and stoichiometric TiN and NbN thin films using RPLD through ablation of high purity titanium and niobium targets, in the presence of low pressure nitrogen gas. A novel Secondary Ion Mass Spectrometry (SIMS) based analysis was developed to effectively deduce the important process parameters in minimum trials to arrive at desired composition. The validity of this SIMS based method, for optimization of process parameters to get stoichiometric nitride films, was proved beyond any speculation by corroborative Proton Elastic Backscattering Spectrometric (PEBS) analysis. SIMS was also used to characterize the [NbN/TiN] multilayers. The feasibility of growing nanocrystalline multilayers with varying thicknesses has been demonstrated. Nanomechanical properties including hardness and adhesion strength of monolithic TiN and NbN films and multilayers were evaluated. The thesis is organised into six chapters. The first chapter gives a brief account on the history and development of ‘surface engineering’. The second chapter provides a comprehensive description of the experimental facility developed in-house to pursue research on PLD grown ceramic thin films and multilayers. Thin film synthesis procedure for ex-situ SIMS and TEM analyses is described. Brief introduction is also presented on the characterization techniques used in this study to investigate the surface, interface and microstructural aspects of PLD grown films with underlying basic principles. The third and fourth chapter describes the synthesis and characterization of titanium nitride and niobium nitride thin films using RPLD technique, respectively. SIMS was used in depth profiling mode, for optimization of three important process parameters, viz., nitrogen gas pressure, substrate temperature and laser pulse energy, to get stoichiometric nitride films. Further, films were characterized using GIXRD, TEM, XPS and PEBS for their structure and composition. AFM measurements were made to elucidate the surface morphological features. PEBS was effectively used to estimate the nitrogen concentration in a quantitative manner and the results corroborate well with the SIMS measurements. Having succeeded in synthesizing stoichiometric TiN and NbN films, further studies on the nanomechanical properties of monolithic TiN and NbN films and their multilayers were carried out and these results form the contents of the fifth chapter. The findings of the work reported in this thesis are concluded in Chapter 6 and few possible suggestions were presented as future directions. Both the monolithic TiN and NbN coatings showed a deposition pressure dependent hardness variation. The hardness of these monolithic films was found to be around 30 GPa, higher than the hardness values obtained by other conventional techniques. Keeping total thickness of the multilayers constant at 1 μm, [NbN/TiN] multilayers having bilayer periods ranging from 50 nm to 1000 nm, were synthesized. A systematic enhancement in hardness upto ~ 40 GPa was observed for [NbN/TiN]10 with the modulus of the multilayer remaining almost constant. The pileup observed around the indentation edge is indicative of toughening in multilayers. The tribological properties of multilayer films showed a better performance in terms of low coefficient of friction and regeneration of coating surfaces as revealed from the nanotribological studies. Overall, the multilayer coatings exhibited better performance in terms of hardness, toughness and adhesion with the substrate material.

White light emitting diodes (LED) have drawn increasing attention due to their low energy consumption, high efficiency and potential to become primary lighting source by replacing conventional light sources. White light emission is usually generated either by coating yellow phosphor on a blue-LED or blending red, green and blue phosphor in an appropriate ratio. Maintaining appropriate proportions of individual components in the blend is difficult and the major demerit of such system is the overall self-absorption, which changes the solution concentration. This results in uncontrolled changes in the whiteness of the emitted light. Zinc Oxide (ZnO), a wide bandgap semiconductor with a large exciton binding energy at room temperature has been recognized as a promising material for ultraviolet LEDs and laser diodes. Tuning of structural, optical and electrical properties of ZnO thin films by different dopants (Lithium, Indium and Gallium) is dealt in this thesis. The achievement of white light emission from a semiconducting material without using phosphors offers an inexpensive fabrication technology, good luminescence, low turn-on voltage and high efficiency. The present work is organized chapter wise, which has 8 chapters including the summary and future work. Chapter 1: Gives a brief discussion on the overview of ZnO as an optoelectronic material, crystal structure of semiconductor ZnO, the effect of doping, optical properties and its possible applications in optoelectronic devices. Chapter 2: Deals with various deposition techniques used in the present study, includes pulsed laser deposition and thermal evaporation. The experimental set up details and the deposition procedures are described in detail. A brief note on the structural characterization equipments, namely X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS) and the optical characterization techniques namely Raman spectroscopy, transmission spectroscopy and photoluminescence (PL) spectroscopy is presented. The electrical properties of the films were studied by current- voltage, capacitance - voltage and Hall Effect measurements and the experimental details are discussed. Chapter 3: High quality ZnO/Si heterojunctions fabricated by growing ZnO thin films on p-type Si (100) substrate by pulsed laser deposition without using buffer layers are discussed in this chapter. The crystallinity of the heterojunction was analyzed by high resolution X-ray diffraction and atomic force microscopy. The optical quality of the film was analyzed by room temperature (RT) photoluminescence measurements. The high intense band to band emission confirmed the high quality of the ZnO thin films on Si. The electrical properties of the junction were studied by temperature dependent resistivity, current- voltage measurements and RT capacitance-voltage (C-V) analysis. ZnO thin film showed the lowest resistivity of 6.4x10-3 Ω.cm, mobility of 7 cm2/V.sec and charge carrier concentration of 1.58x1019cm-3 at RT. The charge carrier concentration and the barrier height (BH) were calculated to be 9.7x1019cm-3 and 0.6 eV respectively from the C-V plot. The BH and ideality factor, calculated by using the thermionic emission (TE) model were found to be highly temperature dependent. We observed a much lower value in Richardson constant, 5.19x10-7 A/cm2K2 than the theoretical value (32 A/cm2K2) for ZnO. This analysis revealed the existence of a Gaussian distribution (GD) with a standard deviation of σ2=0.035 V. By implementing GD to the TE, the values of BH and Richardson constant were obtained as 1.3 eV and 39.97 A/cm2K2 respectively from the modified Richardson plot. The obtained Richardson constant value is close to the theoretical value for n-ZnO. These high quality heterojunctions can be used for solar cell applications. Chapter 4: This chapter describes the structural and optical properties of Li doped ZnO thin films and the properties of ZnO/Li doped ZnO multilayered thin film structures. Thin films of ZnO, Li doped ZnO (ZLO) and multilayer of ZnO and ZLO (ZnO/ZLO) were grown on silicon and Corning glass substrates by pulsed laser deposition technique. Single phase formation and the crystalline qualities of the films were analyzed by X-ray diffraction and Li composition in the film was investigated to be 15 Wt % by X-ray photoelectron spectroscopy. Raman spectrum reveals the hexagonal wurtzite structure of ZnO, ZLO and ZnO/ZLO multilayer, confirms the single phase formation. Films grown on Corning glass show more than 80 % transmittance in the visible region and the optical band gaps were calculated to be 3.245, 3.26 and 3.22 eV for ZnO, ZLO and ZnO/ZLO respectively. An efficient blue emission was observed in all films that were grown on silicon (100) substrate by photoluminescence (PL). PL measurements at different temperatures reveal that the PL emission intensity of ZnO/ZLO multilayer was weakly dependent on temperature as compared to the single layers of ZnO and ZLO and the wavelength of emission was independent of temperature. Our results indicate that ZnO/ZLO multilayer can be used for the fabrication of blue light emitting diodes. Chapter 5: This chapter is divided in to two parts. The fabrication and characterization of In doped ZnO thin films grown on Corning glass substrate is discussed in the first section. Zinc Oxide (ZnO) and indium doped ZnO (IZO) thin films with different indium compositions were grown by pulsed laser deposition technique. The effect of indium concentration on the structural, morphological, optical and electrical properties of the film was studied. The films were oriented along the c-direction with wurtzite structure and are highly transparent with an average transmittance of more than 80 % in the visible wavelength region. The energy band gap was found to be decreasing with increasing indium concentration. High transparency makes the films useful as optical windows while the high band gap values support the idea that the film could be a good candidate for optoelectronic devices. The value of resistivity observed to be decreasing initially with doping concentration and subsequently increasing. The XPS and Raman spectrum confirm the presence of indium in indium doped ZnO thin films. The photoluminescence spectrum showed a tunable red light emission with different In concentrations. Undoped and In doped ZnO (IZO) thin films were grown on Pt coated silicon substrates (Pt/Si) to fabricate Pt/ZnO:Inx Schottky contacts (SC) is discussed in the second section. The SCs were investigated by conventional two probe current-voltage (I-V) measurement and by the I-V spectroscopy of conductive atomic force microscopy (C-AFM). X-ray diffraction technique was used to examine the thin film quality. Changes in various parameters like Schottky barrier height (SBH) and ideality factor (IF) as a function of temperature were presented. The estimated BH was found to be increasing and the IF was found to be decreasing with increase in temperature. The variation of SBH and IF with temperature has been explained by considering the lateral inhomogeneities in nanometer scale lengths at metal–semiconductor (MS) interface. The inhomogeneities of SBH in nanometer scale length were confirmed by C-AFM. The SBH and IF estimated from I-V spectroscopy of C-AFM showed large deviation from the conventional two probe I-V measurements. IZO thin films showed a decrease in SBH, lower turn on voltage and an enhancement in forward current with increase in In concentration. Chapter 6: In this chapter the properties of Ga doped ZnO thin films with different Ga concentrations along with undoped ZnO as a reference is discussed. Undoped and Ga doped ZnO thin films with different Ga concentrations were grown on Corning glass substrates by PLD. The structural, optical and electrical properties of Ga doped ZnO thin films are discussed. The XRD, XPS and Raman spectrum reveal the phase formation and successful doping of Ga on ZnO. All the films show good transmittance in the visible region and the photoluminescence of Ga doped ZnO showed a stable emission in the blue- green region. The resistivity of Ga doped ZnO thin films was found to be first decreasing and then increasing with increase in Ga concentrations. Chapter 7: The effect of co-doping to ZnO on the structural, optical and electrical properties was described in this chapter. Ga and In co-doped ZnO (GIZO) thin films together with ZnO, In doped ZnO (IZO), Ga doped ZnO (GZO), IZO/GZO multilayer for comparison, were grown on Corning glass and boron doped Si substrates by PLD. GIZO showed better structural, optical and electrical properties compared with other thin films. The Photoluminescence spectra of GIZO showed a strong white light emission and the current-voltage characteristics showed relatively lower turn on voltage and larger forward current. The CIE co-ordinates for GIZO were observed to be (0.31, 0.33) with a CCT of 6650 K, indicating a cool white light and established a possibility of white light emitting diodes. Finally the chapter 8 presents the summary derived out of the work and a few suggestions on future work.