Background: The focus of this study was to investigate how producing human bone marrow (hBM) derived mesenchymal stromal cell (MSC) extracellular vehicles (EVs) in a high purity isolation system would affect their established characterization criteria and address the validity of these methods of EV production. Additionally, we set out to functionally characterize the hBM-MSC-EVs for their identified immunomodulatory ability while also assessing the presence of novel MSC-EV marker NRP1 identified by our group to further affirm its validity as a functional MSC-EV identity marker. Methods: Each hBM-MSC-EV donor was cultured in a hollow-fiber bioreactor system in non-stimulating serum/xeno-free conditions for 25 days to produce EVs persistently under quiescent conditions to characterize the hBM-MSC-EVs in their native form. EVs were isolated by traditional PEG-based precipitation for preliminary characterization to monitor bioreactor production wherein they were characterized using multimodal tangential flow filtration coupled with fast protein liquid chromatograph (FPLC) size exclusion/high-affinity purifications to obtain the final highly purified EV sample. Additionally, functional analysis of their immunomodulatory ability, EVs and MSCs were incubated with activated peripheral blood mononuclear cells (PBMCs) as an in-vitro model to evaluate their potency. Results: The hBM-MSC-EVs produced from the bioreactor system showed consistent characterization in accordance with the MISEV2018 establish criteria. We were also able to demonstrate their functional ability by observing statistically significantly immunomodulatory ability of activated PBMCs equivalent to native MSC ability. We were also able to validate the present of NRP1 on all hBM-MSC-EV samples produced confirming its validity as a MSC-EV marker. Conclusion: The significance of the results obtained from this study confirms the production of MSC-EV using a bioreactor and high purity isolation for obtaining consistent MSC-EVs for downstream investigation. Additionally, we were able to demonstrate the significance of MSC-EVs on MSC signaling for immunomodulation by showing equivalent functional potency when tested in-vitro. These results contribute to further understanding the biological attributes of MSC-EVs and contribute to the validation of currently established characterization guidelines.

Ved består huvudsakligen av tre typer av polymerer, cellulosa, hemicellulosa och lignin. Lignin bildas i naturen genom enzymatiskt initierad oxidativ koppling av tre olika typer av fenylpropan-enheter. Dessa bygger genom olika kol-kol- och kol-syre-bindningar upp en amorf tredimensionell polymer. När kemisk massa tillverkas bryts lignin ner och löses ut i kokluten. Luten innehåller de förbrukade kokkemikalierna och bränns generellt i en sodapanna för att regenerera kemikalierna och producera ånga. Sodapannan är emellertid dyr. Därför har den blivit produktionsbegränsande på många massabruk. Att avlägsna en del av ligninet från avluten vore därför önskvärt och att finna ekonomiskt intressanta produkter baserade på lignin från svartlut är därför ett viktigt forskningsområde . Ett lämpligt område för ligninprodukter vore som tillsatts i oblekt massa. Oblekt massa används till stor del för tillverkning av kraftliner, topp- och bottenskikten på wellpapp. När lådor av wellpapp lagras i containrar som färdas över haven, förändras den relativa luftfuktigheten. Detta gör att lådorna kollapsar lättare än om de skulle ha lagrats vid konstant luftfuktighet, även en hög sådan. Detta är på grund av det så kallade mekanosorptiva- eller accelererade krypfenomenet. Genom tillsatts av våtstyrkemedel till kraftliner eller behandla den med hydrofoba ämnen, finns indikatoner på att mekanosorptiva effekten skulle kunna minska. För att försöka minska den effekten har ett lågmolekylärt kraftlignin, som utvunnits med hjälp av tvärsflödesfiltrering av svartlut och svavelsyrafällning, använts. Genom derivatisering av detta lignin med linolja erhölls ett hydrofobt ligninderivat som uppvisar strukturella likheter med biopolymeren suberin. När detta suberinlika ligninderivat tillsätts till massa verkar det mekanosorptiva krypet minska. När lågmolekylärt lignin används tillsammans med ligninradikalinitiatorerna lackas eller mangan(III) i kraftlinermassa erhålls dessutom en våtstyrka på ca 5% av torrstyrkan. Efter aminering av detta lignin gav en tillsatts till kraftlinermassan en våtstyrka på upp till 10% av torrstyrkan. Det finns indikationer på att det mekanosorptiva krypet samtidigt minskar när dessa behandlingar görs som ger upphov till ökad våtstyrka. / Wood consists mainly of three types of polymers; cellulose, hemi cellulose and lignin. Lignin is formed in nature through enzymatic initiated oxidative coupling of three different kinds of phenyl propane units. These form by various carbon-carbon and carbon-oxygen bonds, an amorphous three-dimensional polymer. As chemical pulp is produced, lignin is degraded and dissolved into pulping liquors. These liquors contain the spent cooking chemicals and are generally burnt in a recovery boiler to regenerate cooking chemicals and produce steam. However, the recovery boiler is expensive. Hence, it has become the bottleneck for production in many pulp mills. Removal of some lignin from the spent cooking liquor would, for that reason, be desired and valuable products based on lignin from cooking liquors are searched for. One suitable area for lignin products would be as additive in unbleached pulp. A major product from unbleached pulp is kraftliner, the top and bottom layers of corrugated board. When boxes of corrugated board are stored in containers travelling overseas the relative humidity is varying. This makes the boxes collapse more easily than if they were stored at constant humidity, even a high one. This is due to the so called mechano-sorptive or accelerated creep phenomenon. By addition of wet strength additive to kraftliner or treating it with hydrophobic compounds there are indications on that the mechano-sorptive effect would decrease. Trying to decrease this effect, low molecular weight kraft lignin has been used. It was obtained by cross-flow filtration of black liquor and precipitation by sulphuric acid. By derivatisation of this lignin by linseed oil, a hydrophobic lignin derivative was obtained, similar in structure to units in the biopolymer suberin. As this suberin-like lignin-derivative was added to pulp the mechano-sorptive creep seemed to be lowered. Furthermore, when the low molecular weight lignin was used together with the lignin radical initiators laccase or manganese(III) in kraftliner pulp, a wet strength of about 5% of dry strength was obtained. An amination treatment of this lignin and addition to kraftliner pulp resulted in a wet strength of up to 10% of dry strength. There are indications of that the mechano-sorptive creep also decreases as these treatments, resulting in increased wet strength, are made. / QC 20101103

A non-reactive model system comprising a highly concentrated and unstable oil-in-water emulsion was used to investigate the retention of oil by the membrane in producing biodiesel with a membrane reactor. Critical flux was identified using the relationship between the permeate flux and transmembrane pressure along with the separation efficiency of the membrane. It was shown that separation efficiencies above 99.5% could be obtained at all operating conditions up to the critical flux. It was observed that the concentration of oil in all collected permeate samples using the oil-water system was below 0.2 wt% when operating at a flux below the critical flux. Studies to date have been limited to the characterization of low concentrated emulsions below 15 vol.%. The average oil droplet size in highly concentrated emulsions was measured as 3200 nm employing direct light scattering (DLS) measurement methods. It was observed that the estimated cake layer thickness of 20 to 80 mm was larger than external diameter of the membrane tube i.e. 6 mm based on a large particle size. Settling of the concentrated emulsion permitted the detection of a smaller particle size distribution (30-100 nm) within the larger particles averaging 3200 nm. It was identified that DLS methods could not efficiently give the droplet size distribution of the oil in the emulsion since large particles interfered with the detection of smaller particles. The content of the smaller particles represented 1% of the total weight of oil at 30°C and 5% at 70°C. This was too low to be detected using DLS measurements but was sufficient to affect ultrafiltration. In order to study the critical flux in the presence of transesterification reaction and the effect of cross flow velocity on separation, various oils were transesterified in another membrane reactor providing higher cross flow velocity. higher cross flow velocity provides better separation by reducing materials deposition on the surface of the membrane due to higher shearing. The oils tested were canola, corn, sunflower and unrefined soy oils (Free Fatty Acids (FFA< 1%)), and waste cooking oil (FFA= 9%). The quality of all biodiesel samples was studied in terms of glycerine, mono-glyceride, di-glyceride and tri-glyceride concentrations. The composition of all biodiesel samples were in the range required by ASTM D6751 and EN 14214 standards. A critical flux based on operating pressure in the reactor was reached for waste cooking and pre-treated corn oils. It was identified that the reaction residence time in the reactor was an extremely important design parameter affecting the operating pressure in the reactor. / Natural Sciences and Engineering Research Council of Canada (NSERC)

A non-reactive model system comprising a highly concentrated and unstable oil-in-water emulsion was used to investigate the retention of oil by the membrane in producing biodiesel with a membrane reactor. Critical flux was identified using the relationship between the permeate flux and transmembrane pressure along with the separation efficiency of the membrane. It was shown that separation efficiencies above 99.5% could be obtained at all operating conditions up to the critical flux. It was observed that the concentration of oil in all collected permeate samples using the oil-water system was below 0.2 wt% when operating at a flux below the critical flux. Studies to date have been limited to the characterization of low concentrated emulsions below 15 vol.%. The average oil droplet size in highly concentrated emulsions was measured as 3200 nm employing direct light scattering (DLS) measurement methods. It was observed that the estimated cake layer thickness of 20 to 80 mm was larger than external diameter of the membrane tube i.e. 6 mm based on a large particle size. Settling of the concentrated emulsion permitted the detection of a smaller particle size distribution (30-100 nm) within the larger particles averaging 3200 nm. It was identified that DLS methods could not efficiently give the droplet size distribution of the oil in the emulsion since large particles interfered with the detection of smaller particles. The content of the smaller particles represented 1% of the total weight of oil at 30°C and 5% at 70°C. This was too low to be detected using DLS measurements but was sufficient to affect ultrafiltration. In order to study the critical flux in the presence of transesterification reaction and the effect of cross flow velocity on separation, various oils were transesterified in another membrane reactor providing higher cross flow velocity. higher cross flow velocity provides better separation by reducing materials deposition on the surface of the membrane due to higher shearing. The oils tested were canola, corn, sunflower and unrefined soy oils (Free Fatty Acids (FFA< 1%)), and waste cooking oil (FFA= 9%). The quality of all biodiesel samples was studied in terms of glycerine, mono-glyceride, di-glyceride and tri-glyceride concentrations. The composition of all biodiesel samples were in the range required by ASTM D6751 and EN 14214 standards. A critical flux based on operating pressure in the reactor was reached for waste cooking and pre-treated corn oils. It was identified that the reaction residence time in the reactor was an extremely important design parameter affecting the operating pressure in the reactor. / Natural Sciences and Engineering Research Council of Canada (NSERC)

A non-reactive model system comprising a highly concentrated and unstable oil-in-water emulsion was used to investigate the retention of oil by the membrane in producing biodiesel with a membrane reactor. Critical flux was identified using the relationship between the permeate flux and transmembrane pressure along with the separation efficiency of the membrane. It was shown that separation efficiencies above 99.5% could be obtained at all operating conditions up to the critical flux. It was observed that the concentration of oil in all collected permeate samples using the oil-water system was below 0.2 wt% when operating at a flux below the critical flux. Studies to date have been limited to the characterization of low concentrated emulsions below 15 vol.%. The average oil droplet size in highly concentrated emulsions was measured as 3200 nm employing direct light scattering (DLS) measurement methods. It was observed that the estimated cake layer thickness of 20 to 80 mm was larger than external diameter of the membrane tube i.e. 6 mm based on a large particle size. Settling of the concentrated emulsion permitted the detection of a smaller particle size distribution (30-100 nm) within the larger particles averaging 3200 nm. It was identified that DLS methods could not efficiently give the droplet size distribution of the oil in the emulsion since large particles interfered with the detection of smaller particles. The content of the smaller particles represented 1% of the total weight of oil at 30°C and 5% at 70°C. This was too low to be detected using DLS measurements but was sufficient to affect ultrafiltration. In order to study the critical flux in the presence of transesterification reaction and the effect of cross flow velocity on separation, various oils were transesterified in another membrane reactor providing higher cross flow velocity. higher cross flow velocity provides better separation by reducing materials deposition on the surface of the membrane due to higher shearing. The oils tested were canola, corn, sunflower and unrefined soy oils (Free Fatty Acids (FFA< 1%)), and waste cooking oil (FFA= 9%). The quality of all biodiesel samples was studied in terms of glycerine, mono-glyceride, di-glyceride and tri-glyceride concentrations. The composition of all biodiesel samples were in the range required by ASTM D6751 and EN 14214 standards. A critical flux based on operating pressure in the reactor was reached for waste cooking and pre-treated corn oils. It was identified that the reaction residence time in the reactor was an extremely important design parameter affecting the operating pressure in the reactor. / Natural Sciences and Engineering Research Council of Canada (NSERC)

A non-reactive model system comprising a highly concentrated and unstable oil-in-water emulsion was used to investigate the retention of oil by the membrane in producing biodiesel with a membrane reactor. Critical flux was identified using the relationship between the permeate flux and transmembrane pressure along with the separation efficiency of the membrane. It was shown that separation efficiencies above 99.5% could be obtained at all operating conditions up to the critical flux. It was observed that the concentration of oil in all collected permeate samples using the oil-water system was below 0.2 wt% when operating at a flux below the critical flux. Studies to date have been limited to the characterization of low concentrated emulsions below 15 vol.%. The average oil droplet size in highly concentrated emulsions was measured as 3200 nm employing direct light scattering (DLS) measurement methods. It was observed that the estimated cake layer thickness of 20 to 80 mm was larger than external diameter of the membrane tube i.e. 6 mm based on a large particle size. Settling of the concentrated emulsion permitted the detection of a smaller particle size distribution (30-100 nm) within the larger particles averaging 3200 nm. It was identified that DLS methods could not efficiently give the droplet size distribution of the oil in the emulsion since large particles interfered with the detection of smaller particles. The content of the smaller particles represented 1% of the total weight of oil at 30°C and 5% at 70°C. This was too low to be detected using DLS measurements but was sufficient to affect ultrafiltration. In order to study the critical flux in the presence of transesterification reaction and the effect of cross flow velocity on separation, various oils were transesterified in another membrane reactor providing higher cross flow velocity. higher cross flow velocity provides better separation by reducing materials deposition on the surface of the membrane due to higher shearing. The oils tested were canola, corn, sunflower and unrefined soy oils (Free Fatty Acids (FFA< 1%)), and waste cooking oil (FFA= 9%). The quality of all biodiesel samples was studied in terms of glycerine, mono-glyceride, di-glyceride and tri-glyceride concentrations. The composition of all biodiesel samples were in the range required by ASTM D6751 and EN 14214 standards. A critical flux based on operating pressure in the reactor was reached for waste cooking and pre-treated corn oils. It was identified that the reaction residence time in the reactor was an extremely important design parameter affecting the operating pressure in the reactor. / Natural Sciences and Engineering Research Council of Canada (NSERC)

Membrane filtration processes are widely utilized across different industrial sectors for biological and environmental separations. Examples of the former are sterile filtration and protein fractionation via microfiltration (MF) and ultrafiltration (UF) while drinking water treatment, tertiary treatment of wastewater, water reuse and desalination via MF, UF, nanofiltration (NF) and reverse-osmosis (RO) are examples of the latter. A common misconception is that the performance of membrane separation is solely dependent on the membrane pore size, whereas a multitude of parameters including solution conditions, solute concentration, presence of specific ions, hydrodynamic conditions, membrane structure and surface properties can significantly influence the separation performance and the membrane’s fouling propensity. The conventional approach for studying filtration performance is to use a single lab- or pilot-scale module and perform numerous experiments in a sequential manner which is both time-consuming and requires large amounts of material. Alternatively, high-throughput (HT) techniques, defined as the miniaturized version of conventional unit operations which allow for multiple experiments to be run in parallel and require a small amount of sample, can be employed. There is a growing interest in the use of HT techniques to speed up the testing and optimization of membrane-based separations. In this work, different HT screening approaches are developed and utilized for the evaluation and optimization of filtration performance using flat-sheet and hollow-fiber (HF) membranes used in biological and environmental separations. The effects of various process factors were evaluated on the separation of different biomolecules by combining a HT filtration method using flat-sheet UF membranes and design-of-experiments methods. Additionally, a novel HT platform was introduced for multi-modal (constant transmembrane pressure vs. constant flux) testing of flat-sheet membranes used in bio-separations. Furthermore, the first-ever HT modules for parallel testing of HF membranes were developed for rapid fouling tests as well as extended filtration evaluation experiments. The usefulness of the modules was demonstrated by evaluating the filtration performance of different foulants under various operating conditions as well as running surface modification experiments. The techniques described herein can be employed for rapid determination of the optimal combination of conditions that result in the best filtration performance for different membrane separation applications and thus eliminate the need to perform numerous conventional lab-scale tests. Overall, more than 250 filtration tests and 350 hydraulic permeability measurements were performed and analyzed using the HT platforms developed in this thesis. / Thesis / Doctor of Philosophy (PhD) / Membrane filtration is widely used as a key separation process in different industries. For example, microfiltration (MF) and ultrafiltration (UF) are used for sterilization and purification of bio-products. Furthermore, MF, UF and reverse-osmosis (RO) are used for drinking water and wastewater treatment. A common misconception is that membrane filtration is a process solely based on the pore size of the membrane whereas numerous factors can significantly affect the performance. Conventionally, a large number of lab- or full-scale experiments are performed to find the optimum operating conditions for each filtration process. High-throughput (HT) techniques are powerful methods to accelerate the pace of process optimization—they allow for multiple experiments to be run in parallel and require smaller amounts of sample. This thesis focuses on the development of different HT techniques that require a minimal amount of sample for parallel testing and optimization of membrane filtration processes with applications in environmental and biological separations. The introduced techniques can reduce the amount of sample used in each test between 10-50 times and accelerate process development and optimization by running parallel tests.