Made available in DSpace on 2016-12-08T17:19:39Z (GMT). No. of bitstreams: 1 pre-textuais.pdf: 99837 bytes, checksum: 26af6e9b202afa9fa60be43b442df83a (MD5) Previous issue date: 2011-07-29 / Coordenação de Aperfeiçoamento de Pessoal de Nível Superior / The finite element method has been traditionally applied in solving problems of elasticity and heat transfer, being widely used in cases with homogeneous isotropic materials. With the advent of new technologies, it has been more frequent to use components with more than one material, aiming to get the most out of each phase. A common example is the application of coating films, with optimal properties, on a substrate. These coating films may be homogeneous or functionally graded (FGM). The latter presents a continuous variation of properties through the geometry, allowing to reduce differences at the interface with the substrate. It is important to analyze the behavior of stresses along the interface between film and substrate, a region prone for the occurrence of failure. As current commercial finite element programs have limitations to handle FGM's, especially at the interfaces, one of the motivations of this dissertation is to develop a method for stress and flux nodal recovery, adequate to work with this type of material. The work presents the analysis of a component made of steel or aluminum coated with a titanium nitride film (homogeneous or FGM) under thermo-mechanical loading. The thermal part of the problem is set in an Eulerian description, leading to heat transfer by conduction and convection in the solid. The mechanical (elasticity) part is set in the usual Lagrangean description. A staggered thermo-mechanical approach is implemented and promising results are obtained. / O método de elementos finitos tem sido tradicionalmente aplicado na solução de problemas de elasticidade e transferência de calor, sendo amplamente utilizado em casos com materiais homogêneos e isotrópicos. Com o advento de novas tecnologias tem sido mais freqüente a utilização de componentes com mais de um material, onde se procura obter o máximo proveito de cada fase. Um exemplo comum é a aplicação de filmes de revestimento com propriedades ótimas sobre um substrato. Estes filmes de revestimento podem ser homogêneos ou funcionalmente gradados (FGM), sendo que o último tem variação continua de propriedades ao longo da geometria, permitindo atenuar diferenças na interface com o substrato. A análise do comportamento das tensões ao longo da interface entre filme e substrato é de suma importância, pois esta é uma região potencial para ocorrência de falhas. Dado que programas comerciais de elementos finitos atuais apresentam limitações para lidar com FGM s, principalmente na região de interface, uma das motivações desta dissertação é desenvolver um método de pós-processamento de tensões e fluxos capaz de trabalhar adequadamente com este tipo de material. O trabalho apresenta a análise de um componente de aço ou alumínio revestido com filme de nitreto de titânio (homogêneo ou funcionalmente gradado), sob carregamento termomecânico. A parte térmica do problema é descrita usando uma abordagem Euleriana, que resulta em condução de calor por convecção e condução no sólido. A parte mecânica (elasticidade) é descrita pela tradicional abordagem Lagrangeana. Um procedimento de solução termomecânica aninhada (staggered) é implementado e resultados promissores são obtidos.

O objetivo deste trabalho é controlar a incidência de fissuras em fibrocimentos aplicando o conceito de materiais com gradação funcional através da protensão química gerada pela aplicação de silicato de sódio alcalino entre as camadas dos fibrocimentos. Atualmente é bastante comum os fibrocimentos apresentarem fissuras ao longo das bordas devido aos gradientes de umidade gerados durante a estocagem das pilhas de telhas no pátio das indústrias. O potencial da protensão química foi avaliado através da porosidade total, da quantificação das fases hidratadas, da retração por secagem e do desempenho mecânico. A aplicação de silicato de sódio alcalino no ligante CPII F provocou retração por secagem 1,5 vezes maior que a referência aos 91 dias. O módulo de ruptura (MOR) não sofreu alteração, mas o limite de proporcionalidade da matriz (LOP) aumentou em torno de 95%. O módulo de elasticidade dinâmico foi 13 % maior. O aumento da retração por secagem e o ganho de desempenho mecânico apontam o potencial da protensão química para o controle da fissuração em fibrocimentos produzidos pelo processo Hatschek. / The objective of this work is controlling the incidence of cracks in fiber cement, using the concept of functionally graded materials through the chemical prestressing, generated by application of alkaline sodium silicate among fiber cement layers. Currently, its very common the fiber cements present cracks along the edges due to moisture gradients, caused during storage of piles of tiles in the courtyard of the industry. The chemical prestressing potential was evaluated through of the total porosity, the quantification of hydrate phases, the drying shrinkage and the mechanical performance. The application of alkaline sodium silicate in the cement CPII F caused drying shrinkage 1,5 times greater than the reference to 91 days. The modulus of rupture (MOR) didnt suffer change, but the proportional limit of matrix (LOP) increased by around 95%. The dynamic modulus of elasticity was 13% higher. The increase of drying shrinkage and the mechanical performance gain indicate the chemical prestressing potential to control the cracking in fiber cement produced by the process Hatschek.

Les propriétés idéales d’un matériau de blindage sont la combinaison d’une extrême dureté pour casserles noyaux des projectiles et d’une grande ductilité pour résister à l’impact et arrêter les fragments du projectile. Or cettecombinaison de propriétés est incompatible avec un matériau unique. Pour pallier ce problème, les concepteurs de blindageassocient un matériau dur (céramique) à un matériau ductile (métal). Une autre solution serait de réaliser un matériauprésentant un gradient de propriétés mécaniques : dans le cas présent, d’une très grande dureté de la face avant à une grandeductilité de la face arrière. Les technologies non conventionnelles de frittage telles que le Spark Plasma Sintering (SPS)permettent d’assembler ou de fritter/assembler des matériaux aux caractéristiques aussi différentes et complémentaires. Ils’agit donc d’étudier les conditions d’assemblage ou de cofrittage de tels matériaux (dans le cas présent, Al2O3 et Ti) ainsique l’influence de la microstructure résultante de l’ensemble sur sa performance balistique.La première partie de ce travail a porté sur la caractérisation de l’alumine et du titane. Cinq poudres d’alumines ontété étudiées d’un point de vue comportement au frittage. Trois d’entre elles sont retenues en raison de leurs microstructuresintéressantes, proches en termes de densité et de taille de grains. Ces alumines ont été caractérisées mécaniquement (dureté,ténacité, résistance à la rupture) et balistiquement pour n’en garder qu’une dans la deuxième partie du travail. Le titane, frittédans les mêmes conditions que l’alumine, a montré qu’il n’avait malheureusement pas les propriétés attendues (absence deductilité).La seconde partie du travail a montré que l’obtention de MGFs sains à partir de Al2O3 et Ti uniquement est délicate,que ce soit avec un intercalaire sous forme de monocouche ou de multicouche. La forte affinité du titane avec l’oxygène(formation d’oxyde ou en insertion) et le carbone (formant des carbures), ainsi que sa réactivité avec l’alumine (produisantdes intermétalliques) rend le MGF fragile et incapable d’accommoder les contraintes résiduelles d’élaboration. L’insertiond’une faible proportion de nickel (plus ductile et moins réactif vis-à-vis de l’oxygène que le titane) dans les composites apermis d’obtenir des MGFs sains, dont le comportement balistique a pu être évalué. / The objective is to improve ballistic performance of armors. A perfect armor combines ductility to resistto the impact and high hardness to stop projectile’s fragments. However, such an association of properties is inconsistent witha single material. The solution is to perform a functionally graded material (FGM) with a ductile metal at the back side of thesample and a hard ceramic on the top side. Non-conventional technologies like Spark Plasma Sintering allow joining orsintering all types of materials with different and additional properties. Furthermore, with this technique, high heating ratescan be achieved, limiting grain growth and resulting in a fine microstructure. The goal is to study joining conditions or cosinteringof such materials (in this case, Al2O3 and Ti), as well as the resulting microstructure on the ballistic efficiency.The first part of the study focused on the characterization of alumina and titanium. Five powders of alumina werestudied from a sintering point of view. Three of which were selected because of their interesting microstructures, close indensities and grain sizes. These ceramics have been characterized mechanically (hardness, toughness and strength) andballistically. One of them is adopted to realize FGM. Titanium, sintered with the same conditions, unfortunately, doesn’t haveexpected properties (absence of ductility).The second part of the work showed that the preparation of FGM without cracks from Al2O3 and Ti only ischallenging, with an interlayer with one or more layers. The strong affinity of Ti with oxygen (formation of oxides orinsertion) with C (forming carbides) and its reactivity with alumina (forming intermetallics) make the FGM brittle and enablethe release of residual stresses during the process. By adding a low amount of nickel (more ductile and less reactive withoxygen and titanium) in composites, FGMs almost without cracks were obtained. The latter were evaluated ballistically.

No description available.

Vycházíme-li z lehčených přírodních materiálů, lze od porézních materiálů s gradientem porozity očekávat mechanické vlastnosti nadřazené konvenčím polymerním pěnám, a to díky jejich specifické architektuře. Tyto vlastnosti umožňují použití lehčených materiálů jako strukturních prvků. V této práci je popsaná příprava gradientních porézních materiálů pomocí laminování a/nebo 3D tisku. Provedeny byly statické a dynamické mechanické testy na obou kvazi homogenních a gradientně porézních pěnách poskytující experimentální podklad pro hypotézu deformační odezvy plynoucí ze strukturní architektury. Data se interpretovala užitím zavedených teoretických modelů. Naše výsledky vedly k závěru, že tyto teoretické modely odvozené od pěn s pravidelnou strukturou není vhodné aplikovat pro pěny s gradientem porozity, protože prokazují podstatně lepší mechanické vlastnosti než homogenně porézní pěny.

No description available.

In this study, we quantified the Chemistry-Process-Structure-Property (CPSP) relations of a Ti-6Al-4V/TiB functionally graded material to assess its ability to withstand large deformations in a high throughput manner. The functionally graded Ti-6Al-4V/TiB alloy was created by using a Laser Engineered Net Shaping (LENS) process. A complex thermal history arose during the LENS process and thus induced a multiscale hierarchy of structures that in turn affected the mechanical properties. Here, we quantified the functionally graded chemical composition; functionally graded TiB particle size, number density, nearest neighbor distance, and particle fraction; grain size gradient; porosity gradient. In concert with these multiscale structures, we quantified the associated functionally graded elastic moduli and overall stress-strain behavior of eight materials with differing amounts of titanium, vanadium, aluminum, and boron with just one experiment under compression using digital image correlation techniques. We then corroborated our experimental stress behavior with independent hardening experiments. This paper joins not only the Process-Structure-Property (PSP) relations, but couples the different chemistries in an efficient manner to effectively create the CPSP relationships for analyzing titanium, aluminum, vanadium, and boron together. Since this methodology admits the CPSP coupling, the development of new alloys can be solved by using an inverse method. Finally, this experimental data now lays down the gauntlet for modeling the sequential CPSP relationships.

No description available.

Yes / The ever-increasing demand for high performance electronic and computer systems has unequivocally called for increased microprocessor performance. However, increasing microprocessor performance requires increasing the power and on-chip power density of the microprocessor, both of which are associated with increased heat dissipation. In recent times, thermal management of electronic systems has gained intense research attention due to increased miniaturization trend in the electronics industry. In the paper, we present a numerical study on the performance of a convective-radiative porous heat sink with functionally graded material for improved cooling of various consumer electronics. For the theoretical investigation, the thermal property of the functionally graded material is assumed as a linear and power-law function. We solved the developed thermal models using the Chebyshev spectral collocation method. The effects of inhomogeneity index of FGM, convective and radiative parameters on the thermal behaviour of the porous heat sink are investigated. The present study shows that increase in the inhomogeneity index of FGM, convective and radiative parameter improves the thermal efficiency of the porous fin heat sink. Moreover, for all values of Nc and Rd, the temperature gradient along the fin of FGM is negligible compared to HM fin in both linear and power-law functions. For comparison, the thermal predictions made in the present study using Chebyshev spectral collocation method agrees excellently with the established results of Runge-Kutta with shooting and homotopy analytical method. / Supported in part from PhD sponsorship of the first author by the Tertiary Education Trust Fund of the Federal Government of Nigeria.

A hydrocode and an explicit finite element code were used to evaluate functionally graded material impacts, meteor impacts, and split Hopkinson pressure bar specimens. Modeling impacts of functionally graded projectiles revealed that density was the primary material characteristic controlling the shock wave profile. A parametric study of material order for functionally graded armor showed that arranging the weaker material in front created the greater stopping power. By modeling an array of meteor impact scenarios, deformation and stress were shown to occur at great depths and possibly cause tectonic movement, like subduction. Three proposed Hopkinson specimens, which were designed to produce either shear or tensile reactions under compressive loading, were evaluated. For two of these specimens, improved stress and strain equations were presented.