The separation and reattachment of the suction surface boundary layer in a low pressure turbine is characterized using large-eddy simulation at Re=68,000 based on freestream velocity and suction surface length. A high pass filtered Smagorinsky model is used for modeling the sub-grid scales. The onset of time mean separation is at s=so = 0:61 and reattachment at s=so = 0:81, extending over 20% of the suction surface. The boundary layer is convectively unstable with a maximum reverse flow velocity of about 13% of freestream. The breakdown to turbulence occurs over a very short distance of suction surface which is followed by reattachment. Detailed investigations into the structure and kinematics of the bubble and turbulence statistics are presented. The vortex shed from the bubble, convects downstream and interacts with the trailing edge vortices increasing the turbulence intensity. On the suction side, dominant hairpin structures near the transitional and turbulent flow regime are observed. These hairpin vortices are carried by the freestream even downstream of the trailing edge of the blade with a possibility of reaching the next stage. Longitudinal streaks that evolve from the breakdown of hairpin vortices formed near the leading edge are observed on the pressure surface.

An experimental study was designed to examine and document the development and structures of turbulent 3D offset jets. The generic 3D wall jets at the same Reynolds numbers was used as the basis of comparison. The experiments were performed using a high resolution particle image velocimetry technique to perform velocity measurements at three Reynolds numbers based on the jet exit diameter and velocities of 5000, 10000 and 20000 and four jet offset height ratios of 0.5, 1.0, 2.0 and 4.0. The measurements were performed in the streamwise/wall-normal plane from 0 to 120 jet exit diameters and in the streamwise/lateral plane from 10 to 80 jet exit diameters. The velocity data were analyzed using (i) mean velocities and one-point statistics such as turbulence intensities, Reynolds stresses, triple velocity products and some terms in the transport equations for the turbulence kinetic energy, (ii) two-point velocity correlations to study how the turbulence quantities are correlated as well as the length scale and angle of inclination of the hairpin-like vortex structures, and (iii) proper orthogonal decomposition to examine the energy distribution and the role of the large scale structures in the turbulence intensities and Reynolds shear stresses. The decay of the maximum mean velocities and spread of the jet half widths became independent of Reynolds number much earlier in the generic wall jet than the offset jets. The flow development is delayed with increasing offset heights. The decay rate and wall-normal spread rate increased with the offset heights, whereas the lateral spread rate decreased with offset heights, which is consistent with previous studies. The two-point auto-correlations and the proper orthogonal decomposition results indicate the presence of more large scale structures in the outer and self-similar regions than in the inner and developing regions. The iso-contours of the streamwise autocorrelations in the inner regions were inclined at similar angles of β = 11.2 ± 0.6 degrees, which are in good agreement with reported values in boundary layer studies. The angles decrease with increasing distance from the wall.

This thesis is an experimental study of turbulent flows over smooth and rough walls in a channel that consists of an upstream parallel section to produce a fully developed channel flow and a diverging section to produce an adverse pressure gradient (APG) flow. The roughness elements used were two-dimensional square ribs of nominal height k = 3 mm. The ribs were secured to the lower wall of the channel and spaced to produce the following three pitches: 2k, 4k and 8k, corresponding to d-type, intermediate and k-type rough walls, respectively. For each rough wall type, the ribs were inclined at 90°, 45° and 30° to the approach flow. The velocity measurements were performed using a particle image velocimetry technique. The results showed that rib roughness enhanced the drag characteristics, and the degree of enhancement increased with increasing pitch. The level of turbulence production and Reynolds stresses were significantly increased by roughness beyond the roughness sublayer. It was observed that the population, sizes and the level of organization of hairpin vortices varied with roughness and more intense quadrant events were found over the smooth wall than the rough walls. APG reinforced wall roughness in augmenting the equivalent sand grain roughness height, turbulence production and Reynolds stresses. APG also reduced the sizes of the hairpin packets but strengthened the quadrant events in comparison to the results obtained in the parallel section. The secondary flow induced by inclined ribs significantly altered the distributions of the flow characteristics across the span of the channel. Generally, the mean flow was less uniform close to the trailing edge of the ribs compared to the flows at the mid-span and close to the leading edge of the ribs. The Reynolds stresses and hairpin packets were distinctly larger close to the trailing edge of the ribs. Rib inclination also decreased the drag characteristics and significantly modified the distributions of the Reynolds stresses and quadrant events. In the parallel section, the physical sizes of the hairpin packets were larger over 45° ribs whereas in the diverging section, the sizes were larger over perpendicular ribs.

This thesis is an experimental study of turbulent flows over smooth and rough walls in a channel that consists of an upstream parallel section to produce a fully developed channel flow and a diverging section to produce an adverse pressure gradient (APG) flow. The roughness elements used were two-dimensional square ribs of nominal height k = 3 mm. The ribs were secured to the lower wall of the channel and spaced to produce the following three pitches: 2k, 4k and 8k, corresponding to d-type, intermediate and k-type rough walls, respectively. For each rough wall type, the ribs were inclined at 90°, 45° and 30° to the approach flow. The velocity measurements were performed using a particle image velocimetry technique. The results showed that rib roughness enhanced the drag characteristics, and the degree of enhancement increased with increasing pitch. The level of turbulence production and Reynolds stresses were significantly increased by roughness beyond the roughness sublayer. It was observed that the population, sizes and the level of organization of hairpin vortices varied with roughness and more intense quadrant events were found over the smooth wall than the rough walls. APG reinforced wall roughness in augmenting the equivalent sand grain roughness height, turbulence production and Reynolds stresses. APG also reduced the sizes of the hairpin packets but strengthened the quadrant events in comparison to the results obtained in the parallel section. The secondary flow induced by inclined ribs significantly altered the distributions of the flow characteristics across the span of the channel. Generally, the mean flow was less uniform close to the trailing edge of the ribs compared to the flows at the mid-span and close to the leading edge of the ribs. The Reynolds stresses and hairpin packets were distinctly larger close to the trailing edge of the ribs. Rib inclination also decreased the drag characteristics and significantly modified the distributions of the Reynolds stresses and quadrant events. In the parallel section, the physical sizes of the hairpin packets were larger over 45° ribs whereas in the diverging section, the sizes were larger over perpendicular ribs.