Coordenação de Aperfeiçoamento de Pessoal de Nível Superior / Na reação de desidrogenação oxidativa de propano (ODHP), propano reage com oxigênio da superfície de metais de transição para produzir propeno e água, em temperaturas de 300-700C. Porém, o propeno pode facilmente oxidar, formando CO e CO2. Assim, busca-se catalisadores que promovam a seletividade do propeno. Compostos tipo hidrotalcitas estão sendo apontados como catalisadores de grande potencial para a reação. Portanto, o principal objetivo desse trabalho foi sintetizar precursores tipo hidrotalcitas (contendo íons Ni2+, Mg2+ e Al3+ e tereftalato, heptamolibdato e decavanadato como ânions de compensação) para serem testados na reação de desidrogenação oxidativa de propano. Esses precursores foram sintetizados com uma razão Al/(Al+Ni+Mg)=0,5, variando a razão de Ni/Mg. Além disso, realizou-se a troca iônica do tereftalato (TA) por heptamolibdato (Mo7O24) e decavanadato (V10O28). Esses compostos foram calcinados, obtendo-se assim, óxidos mistos de NiMgAl, NiMgAlMo e NiMgAlV que foram testados como catalisadores na reação de ODHP. Para a determinação das propriedades dos catalisadores foram usadas as técnicas de caracterização: DRX, TGA, volumetria de N2, TPR, Raman e FTIR e ICP. Os resultados indicaram que os materiais tipo hidrotalcita foram obtidos com sucesso. No caso dos precursores preparados por troca iônica a cristalinidade foi menor que os da série NiMgAl-TA. Estes mesmos precursores quando calcinados apresentaram áreas muito altas. Nas três séries, os precursores calcinados são constituídos por óxidos mistos como NiO, NiMoO4, Ni2V2O7 cristalinos e espécies de alumínio e magnésio não detectados na DRX. No teste catalítico de ODHP, observou-se que com o aumento da conversão diminuía a seletividade de propeno, para os óxidos mistos que não continham molibdênio. Os catalisadores da série molibdênio foram os que obtiveram melhor desempenho com altas seletividades, mesmo em altas conversões e a série de cujo precursor foi o tereftalato foi a que exibiu maiores conversões, mas com seletividades menores que da série de Mo / In the reaction of oxidative dehydrogenation of propane (ODHP), propane reacts with oxygen in the transition metal surface to produce propylene and water at temperatures of 300-700 C. However, the propylene can easily oxidize, forming CO and CO2. Thus, catalysts that promote the selectivity of propylene are being searched. Hydrotalcites type compounds are identified as potential major catalysts for the reaction. Therefore, the main objective of this work was to synthesize precursors hydrotalcites type (containing Ni2+, Mg 2+ and Al 3+ ions and terephthalate, heptamolybdate and decavanadate as compensation anions) to test in the reaction of oxidative dehydrogenation of propane.These precursors were synthesized with Al/(Ni+Mg+Al) = 0.5 for different ratios of Ni/Mg. In addition, there was the ion exchange terephthalate (TA) by heptamolybdate (Mo7O24) and decavanadate (V10O28). These compounds were calcined, to obtain NiMgAl, NiMgAlMo and NiMgAlV mixed oxides and tested as catalysts in the ODHP reaction.For determining the properties of the catalysts the following characterization techniques were used: XRD, TGA, N2 volumetry, TPR, ICP, FTIR and Raman spectroscopy. The results indicated that the hydrotalcite-like materials were successfully obtained. In the case of the precursors prepared by ion exchange crystallinity was lower than those of NiMgAl-TA series. These same precursors when calcined had very high areas. In three series, the calcined precursors are comprised by mixed oxides such as crystalline NiO, NiMoO4, Ni2V2O7 and Al an Mg species not detected by XRD. In ODHP catalytic test, it was observed that with increasing conversion the propylene selectivity decreased to the mixed oxides containing no molybdenum. The catalysts of molybdenum series were those who performed better with high selectivity even at high conversions and the terephthalate precursor series shows the highest conversions, but with lower selectivity than Mo series

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior / Na reação de desidrogenação oxidativa de propano (ODHP), propano reage com oxigênio da superfície de metais de transição para produzir propeno e água, em temperaturas de 300-700C. Porém, o propeno pode facilmente oxidar, formando CO e CO2. Assim, busca-se catalisadores que promovam a seletividade do propeno. Compostos tipo hidrotalcitas estão sendo apontados como catalisadores de grande potencial para a reação. Portanto, o principal objetivo desse trabalho foi sintetizar precursores tipo hidrotalcitas (contendo íons Ni2+, Mg2+ e Al3+ e tereftalato, heptamolibdato e decavanadato como ânions de compensação) para serem testados na reação de desidrogenação oxidativa de propano. Esses precursores foram sintetizados com uma razão Al/(Al+Ni+Mg)=0,5, variando a razão de Ni/Mg. Além disso, realizou-se a troca iônica do tereftalato (TA) por heptamolibdato (Mo7O24) e decavanadato (V10O28). Esses compostos foram calcinados, obtendo-se assim, óxidos mistos de NiMgAl, NiMgAlMo e NiMgAlV que foram testados como catalisadores na reação de ODHP. Para a determinação das propriedades dos catalisadores foram usadas as técnicas de caracterização: DRX, TGA, volumetria de N2, TPR, Raman e FTIR e ICP. Os resultados indicaram que os materiais tipo hidrotalcita foram obtidos com sucesso. No caso dos precursores preparados por troca iônica a cristalinidade foi menor que os da série NiMgAl-TA. Estes mesmos precursores quando calcinados apresentaram áreas muito altas. Nas três séries, os precursores calcinados são constituídos por óxidos mistos como NiO, NiMoO4, Ni2V2O7 cristalinos e espécies de alumínio e magnésio não detectados na DRX. No teste catalítico de ODHP, observou-se que com o aumento da conversão diminuía a seletividade de propeno, para os óxidos mistos que não continham molibdênio. Os catalisadores da série molibdênio foram os que obtiveram melhor desempenho com altas seletividades, mesmo em altas conversões e a série de cujo precursor foi o tereftalato foi a que exibiu maiores conversões, mas com seletividades menores que da série de Mo / In the reaction of oxidative dehydrogenation of propane (ODHP), propane reacts with oxygen in the transition metal surface to produce propylene and water at temperatures of 300-700 C. However, the propylene can easily oxidize, forming CO and CO2. Thus, catalysts that promote the selectivity of propylene are being searched. Hydrotalcites type compounds are identified as potential major catalysts for the reaction. Therefore, the main objective of this work was to synthesize precursors hydrotalcites type (containing Ni2+, Mg 2+ and Al 3+ ions and terephthalate, heptamolybdate and decavanadate as compensation anions) to test in the reaction of oxidative dehydrogenation of propane.These precursors were synthesized with Al/(Ni+Mg+Al) = 0.5 for different ratios of Ni/Mg. In addition, there was the ion exchange terephthalate (TA) by heptamolybdate (Mo7O24) and decavanadate (V10O28). These compounds were calcined, to obtain NiMgAl, NiMgAlMo and NiMgAlV mixed oxides and tested as catalysts in the ODHP reaction.For determining the properties of the catalysts the following characterization techniques were used: XRD, TGA, N2 volumetry, TPR, ICP, FTIR and Raman spectroscopy. The results indicated that the hydrotalcite-like materials were successfully obtained. In the case of the precursors prepared by ion exchange crystallinity was lower than those of NiMgAl-TA series. These same precursors when calcined had very high areas. In three series, the calcined precursors are comprised by mixed oxides such as crystalline NiO, NiMoO4, Ni2V2O7 and Al an Mg species not detected by XRD. In ODHP catalytic test, it was observed that with increasing conversion the propylene selectivity decreased to the mixed oxides containing no molybdenum. The catalysts of molybdenum series were those who performed better with high selectivity even at high conversions and the terephthalate precursor series shows the highest conversions, but with lower selectivity than Mo series

<p>Controlling the surface chemistry of 2D materials is critical for the development of next generation applications including nanoelectronics and organic photovoltaics (OPVs). Further, next generation nanoelectronics devices require very specific 2D patterns of conductors and insulators with prescribed connectivity and repeating patterns less than 10 nm. However, both top-down and bottom-up approaches currently used lack the ability to pattern materials with sub 10-nm precision over large scales. Nevertheless, a class of monolayer chemistry offers a way to solve this problem through controlled long-range ordering with superior sub-10 nm patterning resolution. Graphene is most often functionalized noncovalently, which preserves most of its intrinsic properties (<i>i.e.,</i> electronic conductivity) and allows spatial modulation of the surface. Phospholipids such as 1,2-bis(10,12-tricsadiynoyl)-<i>sn­</i>-glycero-3-phosphoethanolamine (diyne PE) form lying down lamellar phases on graphene where both the hydrophilic head and hydrophobic tail are exposed to the interface and resemble a repeating cross section of the cell membrane. Phospholipid is made up of a complex headgroup structure and strong headgroup dipole which allows for a diverse range of chemistry and docking of objects to occur at the nonpolar membrane, these principals are equally as important at the nonpolar interface of 2D materials. A key component in the development of nanoelectronics is the integration of inorganic nanocrystals such as nanowires into materials at the wafer scale. Nanocrystals can be integrated into materials through templated growth on to surface of interest as well as through assembly processes (i.e. interfacial adsorption). </p> <p>In this work, I have demonstrated that gold nanowires (AuNWs) can be templated on striped phospholipid monolayers, which have an orientable headgroup dipoles that can order and straighten flexible 2-nm diameter AuNWs with wire lengths of ~1 µm. While AuNWs in solution experience bundling effects due to depletion attraction interactions, wires adsorb to the surface in a well separated fashion with wire-wire distances (e.g. 14 or 21 nm) matching multiples of the PE template pitch. This suggests repulsive interactions between wires upon interaction with dipole arrays on the surface. Although the reaction and templating of AuNWs is completed in a nonpolar environment (cyclohexane), the ordering of wires varies based on the hydration of the PE template in the presence of excess oleylamine, which forms hemicylindrical micelles around the hydrated headgroups protecting the polar environment. Results suggest that PE template experience membrane-mimetic dipole orientation behaviors, which in turn influences the orientation and ordering of objects in a nonpolar environment.</p> <p>Another promising material for bottom-up device applications is MoS₂substrates due to their useful electronic properties. However, being able to control the surface chemistry of different materials, like MoS₂, is relatively understudied, resulting in very limited examples of MoS₂substrates used in bottom-up approaches for nanoelectronics devices. Diyne PE templates adsorb on to MoS₂­in an edge-on conformation in which the alkyl tails stack on top of each other increasing the overall stability of the monolayer. A decrease in lateral spacing results in high local concentrations of orientable headgroups dipoles along with stacked tails which could affect the interactions and adsorption of inorganic materials (i.e. AuNW) at the interface. </p> <p>Here, I show that both diyne PE/HOPG and diyne PE/MoS₂ substrates can template AuNW of various lengths with long range ordering over areas up to 100 µm². Wires on both substrates experience repulsive interactions upon contact with the headgroup dipole arrays resulting in wire-wire distances greater than the template pitch (7 nm). As the wire length is shortened the measured distance between wires become smaller eventually resulting in tight packed ribbon phases. Wires within these ribbon phases have wire-wire distances equal to the template. Ribbon phases occur on diyne PE/HOPG substrates when the wire length is ~50 nm, whereas wire below ~600 nm produce ribbon phases on diyne PE/MoS_2­substrates. </p> <p>Another important aspect to future scientific development is the catalysis of organic reactions, specifically oxygenation of organic sulfides. Sulfide oxygenation is important for applications such as medicinal chemistry, petroleum desulfurization, and nerve agent detoxification. Both reaction rates and the use of inexpensive oxidants and catalysts are important for practical applications. Hydrogen peroxide and <i>tert</i>-butyl hydroperoxide are ideal oxidants due to being cost efficient and environmentally friendly. Hydrogen peroxide can be activated through transition metal base homogeneous catalysts. Some of the most common catalysts are homo- and hetero-polyoxometalates (POMs) due their chemical robustness. Heptamolybdate [Mo₇O₂₄]^6-is a member of the isopolymolybdate family and its ammonium salt is commercially available and low in cost.²² Heteropolyoxometalates have been widely studied as a catalyst for oxygenation reactions whereas heptamolybdate has been rarely studied in oxygenation reactions. </p> <p> Here I report sulfide oxygenation activity of both heptamolybdate and its peroxo derivate [Mo₇O₂₂(O₂)₂]^6-. Sulfide oxygenation of methyl phenyl sulfide (MPS) by H₂O₂to sulfoxide and sulfone occurs rapidly with 100 % utility of H₂O₂ in the presence of [Mo₇O₂₂(O₂)₂]^6-, suggesting the peroxo adduct is an efficient catalyst. However, heptamolybdate is a faster catalyst compared to [Mo₇O₂₂(O₂)₂]^6- for MPS oxygenation and all other sulfides tested under identical conditions. Pseudo-first order <i>k</i>_cat constants from initial rate kinetics show that [Mo₇O₂₄]^6-catalyzes sulfide oxygenation faster. The significant difference in the <i>k</i>_cat suggests differences in the active catalytic species, which was characterized by both UV-Vis and electrospray ionization mass spectrometry. ESI-MS suggest that the active intermediate of [Mo₇O₂₄]^6-under catalytic reaction conditions for sulfide oxygenation by H₂O₂ is [Mo₂O₁₁]^2-. These results show that heptamolybdate is a highly efficient catalyst for H₂O₂oxygenation of organic sulfides.</p>