Spray cooling of hot surfaces is used in the metallurgical industry during continuous casting, hot rolling or heat treatment. The water is sprayed on the cooled surface by the nozzle which transforms the water stream to droplets. The spray cooling of hot surfaces can be characterized as forced convection with the presence of the boiling. This physically complicated process is influenced by many factors, such as impurities and contaminants in the water, water temperature, water flow rate, droplet size, droplet impact velocity, surface temperature, surface roughness or the presence of oxides (scales) on the cooled surface. The dominant factor that affects the heat transfer during the spray cooling is the water impingement density. Other factors have a smaller but also significant effect. This doctoral thesis deals with the influence of the water temperature, surface roughness and the presence of oxides on the intensity of the spray cooling. These factors are investigated by laboratory experiments in which the hot steel surface is spray cooled. Effect of the oxide layer is also investigated by the numerical simulation. The experimental results are theoretically explained and generalized using mathematical methods.

This work deals with problem of dental implant area, where there are many problems at the dental implants application. The essential issue is the bone tissue quality at implant application, which sig-nificantly influences its deformation, tension and the possibility of subsequent implant failure. The knowledge of bone tissue mechanical properties of mandible and mandible with applied implant can significantly affect prediction of dental implant failure. The mechanical interaction can be described by variable determining deformation and tension of solved system. For this reason the computational modeling by using Finite Element Method was used for solving given problem. The computational model creation of solved system on the high resolution level is necessary for biomechanical assessment of implant failure, including bone tissue quality. For this purpose the biomechanical study was performed, which significantly spreads range of solved problem in this work afterwards. In this work the methodology, which describes assessment of bone tissue quality where the implant should be applied as well as mutual interaction, is presented. The results confirm necessity of bone tissue computational models creation on high resolution level including complex trabecular architecture. In this work the creation of trabecular structure computational model from data gained on micro-CT device is described. Further, the trabecular structure computational model was created on the 3D level with dental implant and the stress strain analysis was performed consequently. The last part of this work deals with introductory study of bone tissue modeling and remodeling.

Kadmium telurid je velmi důležitý materiál jak základního, tak i aplikovaného výzkumu. Je to dáno zejména jeho výhodnými elektronickými, optickými a strukturními vlastnostmi, které ho předurčují pro náročné technické aplikace. Dnes se hlavně používá pro jeho vysoké rozlišení k detekci a X-záření. Hlavní výhodou detektorů na bázi CdTe je, že nepotřebují chlazení a mohou spolehlivě fungovat i při pokojové teplotě. To způsobuje efektivnější interakce fotonů než je tomu u Si nebo jiných polovodičových materiálů. Obsahem této práce byla analýza a interpretace výsledků získaných studiem šumových a transportních charakteristik CdTe vzorků. Měření ukázaly že odpor homogenní části CdTe krystalů mírně klesá při připojení elektrického pole na vzorku. Při změně teploty navíc dochází k odlišné reakci u CdTe typu p a n. Právě těmto efektům je v práci věnována pozornost. Pomocí šumové spektroskopie bylo zjištěno, že při nízkých frekvencích je u vzorků dominantní šum typu 1/f, zatímco při vyšších frekvencích je sledován generačně-rekombinační šum a tepelný šum. Všechny měřené vzorky vykazovaly mnohem vyšší hodnotu šumu na nízkých frekvencích než udává Hoogeova rovnice. Byly nalezeny a popsány zdroje nadbytečného šumu.

Humic acids and humates are principal components of humic substances major organic constituents of soil, peat, coal and water around the world. I was involved in research into molecular dynamics simulations of interactions of quartz surfaces with aqueous solutions of ions and small organic molecules representing basic building blocks of larger biomolecules and functional groups of organic matter. We studied interactions of molecules with surfaces for a set of surface charge densities corresponding to the experimentally or environmentally relevant ranges of pH values employing molecular mechanics, molecular dynamics and ab initio techniques. Simulated quartz surfaces covered the range of surface charge densities 0.00, -0.03, -0.06 and -0.12 C-m-2, approximately corresponding to pH values 4.5, 7.5, 9.5 and 11. As model molecules, benzoic acid, phenol, o-salicylic acid and their conjugated bases were chosen. My task was to prepare topologies and parametric models of selected organic matter basic building blocks organic molecules. I focused on studying interactions of these molecules in an aqueous environment with mineral surface quartz. The aim was to process simulation results and analyse conformations of the adsorption complexes and their thermodynamic properties such as interaction energies, free energies and adsorption geometries.

This diploma thesis deals with the different possible calculations of crack path. Specifically, it focuses on criteria based on maximum tangential stress, minimal strain energy density, crack tip displacement, and local symmetry. These criteria are used for calculations in ANSYS software to estimate possible crack paths on four simple structures. The thesis also contains the codes created in ANSYS. Using these, the crack trajectory of a given structure can be calculated by any of the four criteria described.

The diploma project designs architectural study of Intensive Urban Housing in the city of Brno, district Veveří. Its proposed a building of complex form on vacant site desined by Veveří, Kounicova, Pekárenská and Sokolská Streets which used to be a military grounds. Intensive Urban Housing includes wide community amenities and dwelling for different social groups. As it is located on within walking distance to services which makes the complex self-sufficient, the transport demands are reduced. The proposal works with differentiation of public space, main buildings volumes and facade arrangement that create a lovely city environment and new atractive location in the city of Brno.

The aim of my diploma thesis is to analyze the antenna array radiation and to produce the antenna array radiation computation program. The program should display the electric and magnetic intensity and radiation power density distribution over the planar or cylindrical surface in the near-field area. The antenna array analyzed in this paper consists of a number of elementary dipoles placed in a row with a reflector which represents the conductive board situated in parallel to the row of dipoles. The demonstration program was built in MATLAB and allows computing and displaying the computed values components of antenna array radiation on the planar or the cylindrical surface. The program also allows saving computed values, saving displayed graphs, or saving the adjusted parameters of antenna array. The created program can be used for the presentation of the antenna array radiation in a school laboratory or for the graphical representation when a new antenna is designed.

The magnetic field analysis by MKP and magnetic probe project deals with magnetic field analysis of asynchronous machine cross section. This analysis is written in detail along with the necessary theory of asynchronous machine and the ANSYS program. The magnetic field of selected machine is measured by magnetic probe and results are compared with calculation. The next part of thesis is draft of device for the magnetic field analysis.

This diploma thesis is focused on introducing the mathematical and physical fundamentals of viskosity, density and refractive index of liquids and methods of its measurement. Based on available literatures specify review of areas in which the measurement of dynamic viscosity is used for evaluation the actual state of liquid materials. Discuss the possibility of using for example variables to determine the concentration of fat in milk and ethanol in alcoholic beverages. The sample of liquid to realize the practical measurements.

This thesis describes methods of high frequency noise and vibrations computation of cabin part of EV–55M (aircraft developed by Evektor Kunovice). There is a brief summary of methods used for determining high frequency noise and vibrations in the first part of the thesis. Detailed explanation is given for Statistical Energy Analysis (SEA) which is nowadays the most dominant method in this area. The energy balance equation is derived in this chapter and SEA parameters such as modal density, damping loss factor, coupling loss factor and power input are introduced here. Next part deals with main noise sources of propeller driven and jet aircraft and passive and active noise controls are discussed. Practical part of this thesis deals with modeling aircraft EV–55M fuselage using VA One SEA module. Two models were created. First of them is only an outside fuselage with aircraft flooring and the second one is extended by interior trim panels and is applicable for simulation of noise control treatments. Computational modeling is accompanied by experimental measurement of passive noise control material characteristics. Postprocessing of information obtained from impedance tube measurement was performed in FOAM – X. Determined characteristics of porous material were used as inputs to VA One and reduction of sound pressure level in fuselage cavities by using noise control treatment was found. In conclusion there is a summary of noise transmission paths from sources to interior cavity and some treatments of them are simulated