Spelling suggestions: "subject:"inhalable duty.""
1 |
Performance verification of personal aerosol sampling devicesLuecke, Steven T. 01 January 2003 (has links)
International standards establish criteria for size-selective aerosol sampling for industrial hygiene. Commercially available aerosol samplers are designed to conform to these criteria. This study uses semi-monodispersed aerosols generated in a vertically aligned test chamber to compare the performance of three commercially available respirable dust samplers, one of which can, in addition, simultaneously sample for thoracic and inhalable dust fractions. Comparison methods are used to calculate a theoretical fractional value based on the appropriate sampling conventions of the total dust concentration and size distribution of test materials. Performance of actual samplers can be conducted by comparing observed results to the theoretical value. Results show the design of the test chamber and use of fused aluminum oxide is appropriate to conduct simplified performance verification tests for inhalable and respirable dust samplers.
This study showed the TSI RespiCon followed the inhalable and respirable conventions closely, but results for the thoracic fraction required the use of a correction factor. The SKC aluminum cyclone tended to undersample the respirable fraction, while the BGI CAS4 cyclone and the TSI RespiCon appear to most closely follow the convention. Improved selection of test material and characterization of particle sizes are recommended to further develop this method of performance verification.
|
2 |
Occupational exposure and ill-health among workers during latex glove manufacturing in ThailandSanguanchaiyakrit, Nuthchyawach January 2013 (has links)
Exposure to dust and latex allergens has been well established as a cause of health problems but there have been few studies that have examined the extent of problems in latex glove manufactures, especially in Thailand. Therefore, the overall aim of the study was to determine whether exposure to dust and latex allergens was associated with health problems in Thai latex glove manufacturing workers.The study was conducted in 3 latex glove factories in southern Thailand that employed 1,481 workers (931 Thai and 550 foreign workers). Full shift personal air sampling of workers in 10 different departments was carried out using the IOM Multidust™ sampling Head equipped with 25 mm 1.0 mm Polytetrafluoroethyene filters at a flow rate of 2 L/min. A commercial ELISA kit was employed to quantify levels of the Hev b 6.02 latex allergen in air sample extracts. Information on demographics and, occupational history, exposures and health related problems attributed to work was collected by questionnaires completed by Thai workers. Lung function testing using a spirometer was also conducted among Thai workers. Univariate linear mixed-model analysis was used to determine differences in the dust and specific latex allergen concentrations between factories, departments, shifts and days. Multivariate linear mixed model analysis was used to determine exposure determinants to estimate exposure concentrations of inhalable dust and specific latex allergen. Logistic regression analysis was used to determine association between exposure to inhalable dust and specific latex allergens.292 air samples were collected. The geometric mean (GM) and a range of inhalable dust was 0.88 (0.01 – 12.34) mg/m3. The highest dust levels were found in the Stripping 3.01, (0.73 – 12.34) mg/m3 and lowest in the Office 0.11, (0.06 – 0.92 mg/m3) departments. Hev b 6.02 levels were 9.35 (4.08 – 345.53) ng/m3 and the highest and lowest levels were also found in the Stripping [19.76, (4.72 – 192.90) ng/m3] and Office [5.60, (4.37 – 14.64) ng/m3] departments. Factory and Department were important determinants of both inhalable dust and Hev b 6.02levels. 660 (157 men, 503 women) out of 931 workers completed a self-reported questionnaire. The prevalence of health problems attributed to work was highest for skin problems (25.0%) followed by Rhinitis (23.9%), conjunctivitis (22.5%) and cough (16.2%). Cumulative exposure to dust was associated with conjunctivitis attributed to work (OR and 95%CI = 1.02, [1.00 - 1.03]) after adjusted for confounders. A negative association was found between rhinitis and exposure to average dust level (OR and 95%CI =0.69 [0.48 - 0.99]). No other associations were found between either exposure to dust and self-reported ill-health. There were also no association between exposure to Hev b 6.02 and ill-health although skin problems were associated with the highest Hev b 6.02 level (OR and 95% CI = 1.72 [1.02 - 2.91]). Lung function testing was conducted in 474 Thai workers; 41 had airway restriction, 3 airway obstruction and 1 with a combined problem. Cumulative exposure to dust was associated with airway restriction after adjustment for confounders (OR and 95% CI = 1.02 (1.00 - 1.04).
|
3 |
Performance verification of personal aerosol sampling devices [electronic resource] / by Steven T. Luecke.Luecke, Steven T. January 2003 (has links)
Title from PDF of title page. / Document formatted into pages; contains 48 pages. / Thesis (M.S.P.H.)--University of South Florida, 2003. / Includes bibliographical references. / Text (Electronic thesis) in PDF format. / ABSTRACT: International standards establish criteria for size-selective aerosol sampling for industrial hygiene. Commercially available aerosol samplers are designed to conform to these criteria. This study uses semi-monodispersed aerosols generated in a vertically aligned test chamber to compare the performance of three commercially available respirable dust samplers, one of which can, in addition, simultaneously sample for thoracic and inhalable dust fractions. Comparison methods are used to calculate a theoretical fractional value based on the appropriate sampling conventions of the total dust concentration and size distribution of test materials. Performance of actual samplers can be conducted by comparing observed results to the theoretical value. Results show the design of the test chamber and use of fused aluminum oxide is appropriate to conduct simplified performance verification tests for inhalable and respirable dust samplers. / ABSTRACT: This study showed the TSI RespiCon followed the inhalable and respirable conventions closely, but results for the thoracic fraction required the use of a correction factor. The SKC aluminum cyclone tended to undersample the respirable fraction, while the BGI CAS4 cyclone and the TSI RespiCon appear to most closely follow the convention. Improved selection of test material and characterization of particle sizes are recommended to further develop this method of performance verification. / System requirements: World Wide Web browser and PDF reader. / Mode of access: World Wide Web.
|
Page generated in 0.0417 seconds