1 |
Thermally and Chemically Induced Changes in Interface Shear Behavior of Landfill LinersLi, Ling January 2015 (has links)
Composite liners are used in landfills to isolate solid waste from the local environment. The combination of a high-density polyethylene (HDPE) geomembrane and compacted clay liner (CCL) is commonly used worldwide. In the Ontario region, bentonite sand mixtures (BSMs) and the local clay i.e. Leda clay, can be considered as appropriate CCL materials. However, the interface failure between smooth HDPE and CCL is a critical issue for landfill safety. The shear stress behavior and strength parameters at the interface between the HDPE and CCL can be affected by many factors, such as temperature and chemicals. The temperature difference between winter and summer in the Ontario region is approximately 50°C, which causes a freeze-thaw (F-T) phenomenon in local landfills. Leachate and heat are generated during the solid waste stabilization process. Landfill leachate usually contains a high concentration of cations, which can carry heat, thus affecting the landfill liner properties. As a result, the interface shear stress behavior and strength parameters are affected by the aforementioned conditions.
In this thesis, a series of experiments were conducted on the shear stress behavior at the interface of Leda clay / HDPE and bentonite sand mixture (BSM) / HDPE. In order to understand the influence of the F-T phenomenon, the samples were tested by varying the number of F-T cycles. Meanwhile, in order to understand the combined influence of cations and heat, the samples were saturated with different solutions, i.e. distilled water, potassium chloride and calcium chloride solutions. Then they were cured in an oven with different temperatures and room temperature, respectively. All of the laboratorial shear tests have been performed by using a direct shear machine. Results show that the BSM /HDPE and Leda clay/ HDPE interfaces are both influenced by the F-T cycles. The BSM/HDPE interface shear of the samples between 0 and 5 F-T cycles has more obvious differences, while the friction angle of compacted Leda clay/HDPE exhibits distinct reduction in the first 3 cycles, after which, the difference becomes hard to differentiate. The results also indicate that both high temperature and high concentration of cations from leachate can slight reduce the interface shear stress of BSM/HDPE. However, the combined influence of thermal-chemical conditions is not much more obvious compared to the effects of a single thermal or chemical condition. The BSM materials, which were saturated with different solutions, are also tested by using X-ray diffraction to examine the mineral changes in the BSM. The calcium and potassium cations convert sodium-bentonite into calcium-rich bentonite and illite/semectie mixtures, respectively. Nevertheless, the changess of clay part caused by the combined effect of heat and leachate have limited influence on the BSM/HDPE interface shear behavior.
|
2 |
Elevated temperature effects on interface shear behaviorKarademir, Tanay 25 August 2011 (has links)
Environmental conditions such as temperature inevitably impact the long term performance, strength and deformation characteristics of most materials in infrastructure applications. The mechanical and durability properties of geosynthetic materials are strongly temperature dependent. The interfaces between geotextiles and geomembranes as well as between granular materials such as sands and geomembranes in landfill applications are subject to temperature changes due to seasonal temperature variations as well as exothermic reactions occurring in the waste body. This can be a critical factor governing the stability of modern waste containment lining systems. Historically, most laboratory geosynthetic interface testing has been performed at room temperature. Information today is emerging that shows how temperatures in the liner systems of landfills can be much higher.
An extensive research study was undertaken in an effort to investigate temperature effects on interface shear behavior between (a) NPNW polypropylene geotextiles and both smooth PVC as well as smooth and textured HDPE geomembranes and (b) sands of different angularity and smooth PVC and HDPE geomembranes. A temperature controlled chamber was designed and developed to simulate elevated temperature field conditions and shear displacement-failure mechanisms at these higher temperatures. The physical laboratory testing program consisted of multiple series of interface shear tests between material combinations found in landfill applications under a range of normal stress levels from 10 to 400 kPa and at a range of test temperatures from 20 to 50 °C.
Complementary geotextile single filament tensile tests were performed at different temperatures using a dynamic thermo-mechanical analyzer (DMA) to evaluate tensile strength properties of geotextile single filaments at elevated temperatures. The single filament studies are important since the interface strength between geotextiles and geomembranes is controlled by the fabric global matrix properties as well as the micro-scale characteristics of the geotextile and how it interacts with the geomembrane macro-topography.
The peak interface strength for sand-geomembrane as well as geotextile-geomembrane interfaces depends on the geomembrane properties such as hardness and micro texture. To this end, the surface hardness of smooth HDPE and PVC geomembrane samples was measured at different temperatures in the temperature controlled chamber to evaluate how temperature changes affect the interface shear behavior and strength of geomembranes in combination with granular materials and/or geotextiles. The focus of this portion of the experimental work was to examine: i) the change in geomembrane hardness with temperature; ii) develop empirical relationships to predict shear strength properties of sand - geomembrane interfaces as a function of temperature; and iii) compare the results of empirically predicted frictional shear strength properties with the results of direct measurements from the interface shear tests performed at different elevated temperatures.
|
3 |
Shear Behaviour of Sand-geosynthetic Interfaces Based on Size And Morphology of Sand Particles and Surface Roughness of GeosyntheticsVangla, Prashanth January 2016 (has links) (PDF)
Geosynthetics are used in conjunction with soil/particulate materials to serve various functions like reinforcement, drainage, filtration and containment. The shear behavior of soil-geosynthetic interfaces hugely depends upon on the morphological properties of particulate materials and surface characteristics of geosynthetics. However, many researchers have ignored the effects of morphology, owing to the difficulty in finding the morphological characteristics of sand particles. Few of them used visual, manual and imaged based quantifications, which are not very effective. Also, the effects of particle size and morphology are often combined and the individual effect of these parameters cannot be easily separated. In addition to this, there are very few studies which have given importance to quantitative understanding of surface features/roughness of geosynthetics and almost all of them are limited to 2D surface measurements.
The objective of this thesis is to understand the interface shear mechanisms of sand-geosynthetic systems through modified large interface direct shear tests coupled with morphological characterization of sands using advanced image based and optical techniques and surface topographical analysis of geosynthetics using 3D interferometry. The individual effects of particle size and morphology on interface shear mechanism are investigated by carefully selecting the sands having specific size fractions and different morphological characteristics.
A new computational method based on image analysis is proposed in this study to quantify the morphology of sands (roundness, sphericity and roughness) more accurately by writing several algorithms and implementing them in MATLAB. The roundness and sphericity of sand particles in this method are quantified as per Wadell (1932) and Krumbein and Sloss (1963) respectively and the root mean square roughness is used as a measure of surface roughness. Out of total four sands, namely coarse sand (CS), medium sand (MS), fine sand (FS) and angular coarse sand (ACS) used in this study, CS, MS and FS have similar morphology and different particle sizes, whereas CS and ACS have same size and dissimilar morphology. The effects of size and morphology of sand particles on the interface shear behavior are examined through direct shear tests on dilative and non-dilative interfaces.
After examining the boundary effects on deformation patterns analyzed using shear bands in conventional, fixed box and symmetric interface direct shear tests, symmetric interface direct shear test is observed to show uniformity in stresses and deformations across the shear box and hence the same is adopted in this thesis. Test results revealed that the peak interface friction and dilation angles in case of dilative interfaces are hugely dependent upon the interlocking between the sand particles and the asperities of geosynthetic material, which in turn depend on the relative size of sand particles and asperities. Highest interface shear strength is observed when the asperity size of the geosynthetic material matches with the mean particle size of sand, which is also manifested in terms of highest shear band thickness.
Direct shear tests on non-dilative interfaces (sand-smooth geomembrane) revealed that interface friction angle depends on the number of effective contacts rather than the particle size. Morphology of sands is found to have major influence on the interface shear strength among all the parameters investigated. Results from interface shear tests are examined in the light of topographical analysis of sand particles and shear induced surface changes in geomembrane. Possible shearing mechanisms at the interface and the influence of particle size, morphology and normal stress on sliding or plowing are brought out from 3D surface roughness measurements using 3D optical profilometer. The stress-shear displacement response of sand-geomembrane interfaces are correlated to the surface changes on sheared geomembranes through visual observations and roughness quantifications. Medium sand used in this study could make more number of effective contacts with deeper grooves, resulting in highest interface friction. The number of grooves are less in case of coarse sand and the depth of grooves is less in case of fine sand, resulting in lesser interface friction for these two sands compared to medium sand, supporting the results of interface shear tests.
|
Page generated in 0.0977 seconds