Landslides are relatively frequent in Ottawa due to the presence of sensitive marine clays (Leda clay or Champlain Sea clay), and the presence of natural or climatic triggers such as rainfall or snowmelt. A geographic information system (GIS) based modeling tool has been developed to assess and predict climate (rainfall and snowmelt)-induced landslides in the sensitive marine clays of the Ottawa region. The Transient Rainfall Infiltration and Grid-based Regional Slope-Stability (TRIGRS) model is used in a GIS framework to investigate the influence of rainfall and snowmelt on shallow landslides through the Ottawa region, with respect to time and location. First, the GIS and TRIGRS models are combined to assess landslide susceptibility with respect to rainfall. The GIS-TRIGRS approach requires topographic, geologic, hydrologic, and geotechnical information of the study area. In addition to this technical information (input data), rainfall intensity data for different durations (5 minutes, and 6, 12, 18, and 24 hours), and historical data of the regional landslides is required. This data is used to verify the locations of predicted landslide-susceptible areas with respect to historical landslide maps in the area. The generated results from the GIS-TRIGRS model were verified by comparing the predicted and historical locations of shallow landslides induced by rainfall throughout the Ottawa region. The comparison results showed a high correlation between the predicted areas of landslides and the previously reported landslides. In addition, the results also indicated that not all previous landslides in Leda clays were triggered by rainfall. The second application of the developed GIS-TRIGRS approach was used to assess and predict snowmelt-induced landslides in areas of sensitive marine clay in the Ottawa region. Similar to the first analysis, the approach requires the following input data: topographic, geologic, hydrologic, geotechnical, snowmelt intensity data for various periods (6–48 hours, 3–15 days, 25 days, and 30 days), This approach also requires data indicating the location of historical landslides in the study area. Using this data, we examine both the timing and location of shallow landslides due to snowmelt in a GIS-based framework. The developed model was validated by comparing the predicted landslide-susceptible areas to historical landslide maps in the study area. A high correlation between predicted and historical landslide location trends was obtained, confirming that the developed GIS-TRIGRS model can predict the snowmelt-induced landslide susceptibility in the sensitive marine clays relatively well. The model results reinforced the conclusion that areas with high slopes and sensitive marine clays were more prone to snowmelt-induced landslides. Finally, in a Geographic Information System (GIS) the landslide occurrence susceptibility in the Ottawa area was modeled. Results of such models are presented as maps showing landslide susceptibility in Champlain Sea clays (Leda clays) in the Ottawa area due to both rainfall and snowmelt. Various input data was collected and entered into a GIS and TRIGRS model. The main categories of such inputs are climate, topography, geology, hydrology, and geotechnical data. The rainfall and snowmelt intensity data was extracted for 24 to 48 hour periods from Environment and Climate Change Canada historical climate records. Thereafter, the factor of safety was calculated in order to determine the stability of slopes across the study area. The model assesses the effects of rainfall and snowmelt on landslide occurrence, and based on the calculated factor of safety at each pixel of the study area, the model calculates the landslide susceptibility. The results presented in this thesis will provide a geotechnical basis for making appropriate engineering decisions during slope management and land use planning in the Ottawa region.

Composite liners are used in landfills to isolate solid waste from the local environment. The combination of a high-density polyethylene (HDPE) geomembrane and compacted clay liner (CCL) is commonly used worldwide. In the Ontario region, bentonite sand mixtures (BSMs) and the local clay i.e. Leda clay, can be considered as appropriate CCL materials. However, the interface failure between smooth HDPE and CCL is a critical issue for landfill safety. The shear stress behavior and strength parameters at the interface between the HDPE and CCL can be affected by many factors, such as temperature and chemicals. The temperature difference between winter and summer in the Ontario region is approximately 50°C, which causes a freeze-thaw (F-T) phenomenon in local landfills. Leachate and heat are generated during the solid waste stabilization process. Landfill leachate usually contains a high concentration of cations, which can carry heat, thus affecting the landfill liner properties. As a result, the interface shear stress behavior and strength parameters are affected by the aforementioned conditions. In this thesis, a series of experiments were conducted on the shear stress behavior at the interface of Leda clay / HDPE and bentonite sand mixture (BSM) / HDPE. In order to understand the influence of the F-T phenomenon, the samples were tested by varying the number of F-T cycles. Meanwhile, in order to understand the combined influence of cations and heat, the samples were saturated with different solutions, i.e. distilled water, potassium chloride and calcium chloride solutions. Then they were cured in an oven with different temperatures and room temperature, respectively. All of the laboratorial shear tests have been performed by using a direct shear machine. Results show that the BSM /HDPE and Leda clay/ HDPE interfaces are both influenced by the F-T cycles. The BSM/HDPE interface shear of the samples between 0 and 5 F-T cycles has more obvious differences, while the friction angle of compacted Leda clay/HDPE exhibits distinct reduction in the first 3 cycles, after which, the difference becomes hard to differentiate. The results also indicate that both high temperature and high concentration of cations from leachate can slight reduce the interface shear stress of BSM/HDPE. However, the combined influence of thermal-chemical conditions is not much more obvious compared to the effects of a single thermal or chemical condition. The BSM materials, which were saturated with different solutions, are also tested by using X-ray diffraction to examine the mineral changes in the BSM. The calcium and potassium cations convert sodium-bentonite into calcium-rich bentonite and illite/semectie mixtures, respectively. Nevertheless, the changess of clay part caused by the combined effect of heat and leachate have limited influence on the BSM/HDPE interface shear behavior.

Sensitive marine clay in Ottawa is a challenging soil for geotechnical engineers. This type of clay behaves differently than other soils in Canada or other parts of the world. They also have different engineering characteristic values in comparison to other clays. Cone penetration testing in sensitive marine clays is also different from that carried out in other soils. The misestimation of engineering characteristics from cone penetration testing can result. Temperature effects have been suspected as the reason for negative readings and erroneous estimations of engineering characteristics from cone penetration testing. Furthermore, the applicability of correlations between cone penetration test (CPT) results and engineering characteristics is ambiguous. Moreover, it is important that geotechnical engineers who need to work with these clays have background information on their engineering characteristics. This thesis provides comprehensive information on the engineering characteristics and behaviour of sensitive marine clays in Ottawa. This information will give key information to geotechnical engineers who are working with these clays on their behaviour. For the purpose of this research, fifteen sites in the Ottawa area are taken into consideration. These sites included alternative technical data from cone and standard penetration tests, undisturbed samples, field vanes, and shear wave velocity measurements. Laboratory testing carried out for these sites has resulted in acquiring engineering parameters of the marine clay, such as preconsolidation pressure, overconsolidation ratio, compression and recompression indexes, secondary compression index, coefficient of consolidation, hydraulic conductivity, clay fraction, porewater chemistry, specific gravity, plasticity, moisture content, unit weight, void ratio, and porosity. This thesis also discusses other characteristics of sensitive marine clays in Ottawa, such as their activity, sensitivity, structure, interface shear behaviour, and origin and sedimentation. Furthermore, for the purpose of increasing local experience with the use of cone and ball penetrometers in sensitive marine clays in Ottawa, three types of penetrometer tips are used in the Canadian Geotechnical Research Site No. 1 located in south-west Ottawa: 36 mm cone tip, and 40 mm and 113 mm ball tips. The differences in their response in sensitive marine clays will be discussed. The temperature effects on the penetrometer equipment are also studied. The differences in the effect of temperature on these tips are discussed. Correlations between the penetrometer results and engineering characteristics of Ottawa's clays are verified. The applicability of correlations between the testing results and engineering characteristics of sensitive marine clays in Ottawa is also presented in this thesis. Two correlations from the Canadian Foundation Engineering Manual are examined. One of these correlations is between the N60 values from standard penetration testing and undrained shear strength. The other correlation is between the shear wave velocity measurement and site class. Temperature corrections are suggested and discussed for penetrometer equipment according to laboratory calibrations. The significance of the effects due to radical temperature changes in Canada and Ottawa is discussed. Some of the main findings from this research are as follows. • The Canadian Foundation Engineering Manual presents a correlation between standard penetration tests (SPTs) and the undrained shear strength of soils. This relationship may not be applicable to sensitive marine clays in Ottawa. • Another correlation between the site class, shear wave velocity, and undrained shear strength is presented by this same manual which may not be applicable to sensitive marine clays in Ottawa. • The rotation rate for field vane testing as recommended by ASTM D2573 is slow for sensitive marine clays in Ottawa. • Correction factors applied to undrained shear strength from laboratory vane tests may not result in comparable values with the undrained shear strength obtained by using field vane tests. • Loading schemes in consolidation or oedometer testing may affect the quality of the targeted results. • Temperature corrections should be applied to penetrometer recordings to compensate for the drift in the results of these recordings due to temperature changes. • The secondary compression index to compression index ratio presented in the literature may not be the value obtained from this research.

Sensitive marine clay in Ottawa is a challenging soil for geotechnical engineers. This type of clay behaves differently than other soils in Canada or other parts of the world. They also have different engineering characteristic values in comparison to other clays. Cone penetration testing in sensitive marine clays is also different from that carried out in other soils. The misestimation of engineering characteristics from cone penetration testing can result. Temperature effects have been suspected as the reason for negative readings and erroneous estimations of engineering characteristics from cone penetration testing. Furthermore, the applicability of correlations between cone penetration test (CPT) results and engineering characteristics is ambiguous. Moreover, it is important that geotechnical engineers who need to work with these clays have background information on their engineering characteristics. This thesis provides comprehensive information on the engineering characteristics and behaviour of sensitive marine clays in Ottawa. This information will give key information to geotechnical engineers who are working with these clays on their behaviour. For the purpose of this research, fifteen sites in the Ottawa area are taken into consideration. These sites included alternative technical data from cone and standard penetration tests, undisturbed samples, field vanes, and shear wave velocity measurements. Laboratory testing carried out for these sites has resulted in acquiring engineering parameters of the marine clay, such as preconsolidation pressure, overconsolidation ratio, compression and recompression indexes, secondary compression index, coefficient of consolidation, hydraulic conductivity, clay fraction, porewater chemistry, specific gravity, plasticity, moisture content, unit weight, void ratio, and porosity. This thesis also discusses other characteristics of sensitive marine clays in Ottawa, such as their activity, sensitivity, structure, interface shear behaviour, and origin and sedimentation. Furthermore, for the purpose of increasing local experience with the use of cone and ball penetrometers in sensitive marine clays in Ottawa, three types of penetrometer tips are used in the Canadian Geotechnical Research Site No. 1 located in south-west Ottawa: 36 mm cone tip, and 40 mm and 113 mm ball tips. The differences in their response in sensitive marine clays will be discussed. The temperature effects on the penetrometer equipment are also studied. The differences in the effect of temperature on these tips are discussed. Correlations between the penetrometer results and engineering characteristics of Ottawa's clays are verified. The applicability of correlations between the testing results and engineering characteristics of sensitive marine clays in Ottawa is also presented in this thesis. Two correlations from the Canadian Foundation Engineering Manual are examined. One of these correlations is between the N60 values from standard penetration testing and undrained shear strength. The other correlation is between the shear wave velocity measurement and site class. Temperature corrections are suggested and discussed for penetrometer equipment according to laboratory calibrations. The significance of the effects due to radical temperature changes in Canada and Ottawa is discussed. Some of the main findings from this research are as follows. • The Canadian Foundation Engineering Manual presents a correlation between standard penetration tests (SPTs) and the undrained shear strength of soils. This relationship may not be applicable to sensitive marine clays in Ottawa. • Another correlation between the site class, shear wave velocity, and undrained shear strength is presented by this same manual which may not be applicable to sensitive marine clays in Ottawa. • The rotation rate for field vane testing as recommended by ASTM D2573 is slow for sensitive marine clays in Ottawa. • Correction factors applied to undrained shear strength from laboratory vane tests may not result in comparable values with the undrained shear strength obtained by using field vane tests. • Loading schemes in consolidation or oedometer testing may affect the quality of the targeted results. • Temperature corrections should be applied to penetrometer recordings to compensate for the drift in the results of these recordings due to temperature changes. • The secondary compression index to compression index ratio presented in the literature may not be the value obtained from this research.