This thesis deals with the design grate boilers with natural circulation for the combustion of contaminated biomass. The boiler output is output 45 t/h. Produced superheated steam with the output parameters of 440 °C 4,2 at MPa feed water temperature 115 °C. The stoichiometric calculations and the thermal calculation are based on the specified fuel composition. Thanks to this, the basic dimensional design of the boiler and its efficiency are determined. Calculation of this work focuses mainly on thermal calculations and dimensional design of individual heat transfer surfaces. Basic drawing of the boiler is available in the attachment of the thesis.

This master’s thesis deals with the possibility of increasing efficiency of energy blocks with combustion engines by the combination of the Sabat and Clausius-Rankine cycle into the combined cycle. In the thesis is briefly described the principle of the function of the auxiliary device, which can increase the efficiency of the combustion engine. This device, which consists of a waste heat boiler and two turbine modules, is designed using calculations. Both turbine modules are prepared with drawing documentation and there are described important structural elements. Each key part of the thesis is given by a brief theory, so the basic theory of combustion engines, waste heat boilers and steam turbine are described.

The master’s thesis deals with the design of a boiler for RDF combustion, based on the required power output and superheated steam parameters. The first part of the thesis focuses on combustion calculations. Boiler efficiency is also calculated in this chapter, using the heat balance efficiency method. The main part of the thesis consists of dimensional design and heat transfer calculations. The precision of the calculations is checked at the end of the thesis along with the chlorine corrosion, which is considered because of the higher amount of chlorine in the fuel. The thesis comes with a basic schematic of the designed boiler.

The aim of the thesis is a design of a grate steam boiler with capacity of 35 t/h and output steam parameters with temperature 430 °C and pressure 4,1 MPa. The first part of the thesis deals with stoichiometric calculations and boiler efficiency. The theses mainly focuses on the heat transfer calculation and the geometric design of individual heat transfer surfaces. The specifics of fuel are taken into consideration. The drawing of the basic boiler scheme is a part of the thesis.

This thesis deals with a design of a steam boiler combusting natural gas. It consists of stoichiometric calculation, determination of boiler efficiency, thermal calculations and determining geometric parameters of the boiler and its heat transfer surfaces. The results are verified by the heat balance of the boiler.

For set parameters of a steam and a boiler feed water is designed a thermal and dimensional plan of the boiler, allowing high efficient requests. A boiler is used for combustion of blast furnace gas contains 10% of a natural gas used as a stabilisation element.

This master thesis deals with design of grate biomass boiler with 50 t/h power. A fuel of the boiler is a mixture of contaminated biomass and woodchips. The boiler produces steam with parameters of 4,2 MPa and 420 °C. Stochiometric and thermal calculations are based on given fuel composition and output steam parameters. Heat exchangers are designated in accordance with the calculations. General drawing of the boiler is attached to this document. Anti-corrosion measures are considered, due to chlorine content in biomass. Hydraulic and aerodynamic losses and dew point of the flue gas is calculated in the end.

This thesis deals with the change of the fuel base of a coal boiler due to the reduction of CO2 emissions and its thermal recalculation. In the first part, there is implemented calculation of the combusting chamber. This is followed by the recalculation of the heat transfer surfaces. The emphasis is placed on the preservation of the exsiting steam parametrs.

This master’s thesis deals with utilization of biomass for micro cogeneration. The theoretical part of the master’s thesis defines main terms of the master’s thesis, which is biomass and cogeneration. The practical part of the master’s thesis is focused on the design and manufacturing of small micro cogeneration unit based on a small membrane steam engine. It means design of two steam generators to produce steam for the membrane steam engine. It will be also carried out design and production of membrane steam engine which is fitted with a small BLDC generator including electrical part for power output and measuring parameters. It will be made several measurements with the steam engine including measuring power output characteristic of the steam engine and measuring loading characteristics of the generator.

The topic of this thesis is the calculation of the steam-boiler on biomass. This thesis deals with stoichiometry, the calculation of enthalpies of combustion gas, the heat balance of the boiler and the results in fixing the efficiency of the boiler, the calculation of fire and the balance heat calculation of component parts of the boiler. Onward follow detailed calculations of particular heating surfaces. The output parametres are temperature, pressure and the amount of steam.