High power thulium fiber lasers are interesting for a myriad of applications due to their potential for high average output power, excellent beam quality, compactness, portability, high operating efficiency and broad, eye-safe spectral range from 1.8-2.1 microns. Currently, the majority of thulium laser research effort is being invested into scaling average output powers; however, such output powers are being scaled with no degree of control on laser system output spectrum or temporal behavior. Thulium fiber laser technology is not useful for many of its most important applications without implementation of techniques enabling tunable, narrow spectral widths with appropriate pulse durations for particular applications. This work outlines several techniques for spectral control of thulium fiber lasers and investigates scaling of average laser powers while using these techniques to maintain a desired spectral output. In addition, an examination of operation in both nanosecond and picosecond pulsed regimes and scaling of average powers and pulse energies in these regimes to useful power levels is conducted. The demonstration of thulium fiber laser systems for applications in frequency conversion and spectral beam combination is also discussed. In addition to the experimental results, theoretical modeling of thulium fiber amplifier operation, simple thermal management analysis, as well as practical fiber and system design considerations for future power scaling are presented. Experimental and theoretical results of this work will enable the successful design of future extremely high power spectrally and temporally controlled thulium fiber laser systems.

Ce travail concerne le développement d’une fibre optique à structure originale permettant la montée en puissance moyenne et crête dans les systèmes lasers à 2μm. La gestion des effets thermiques est devenue aujourd’hui un enjeu primordial notamment pour essayer de repousser le seuil d’apparition des instabilités modales transverses. Le principe mis en avant ici est basé sur la rupture de symétrie de la gaine microstructurée de la fibre afin d’améliorer la délocalisation des modes d’ordre supérieur vers l’extérieur du milieu à gain. Ainsi une propagation quasi-monomode est obtenue dans une fibre apériodique passive avec un coeur de 140μm à 2μm. Un travail de modélisation a été mené de manière à proposer d’autres structures basées sur une modulation contrôlée de l’indice de réfraction dans le milieu à gain afin de repousser encore plus le seuil du régime multimode. En outre, la fabrication de la première fibre dopée thulium à large aire modale (Dcoeur = 18μm) par la méthode REPUSIL a montré une efficacité de 50%. Ensuite, la fabrication de la première fibre rigide complètement apériodique à gaine réduite dopée thulium a été réalisée. Une fibre avec un coeur de 29μm et un diamètre extérieur de 769μm et une longueur de 86cm a été caractérisée en configuration laser et a permis d’obtenir une émission laser à 2μm de 3,8W (puissance limitée par la puissance de la diode de pompe disponible) avec un rendement de 20% et une qualité de faisceau quasi-monomode. De plus, une fibre passive complètement apériodique à polarisation unique avec un coeur de 140μm a également été réalisée et a permis d’obtenir un ratio d’extinction de polarisation de 16,5dB à 2μm. / This work deals with the development of an original leaky structure of optical fiber aiming at generating a high power laser radiation at 2μm in CW and pulsed regimes. The management of thermal effects in high power/energy regime became a major issue, in particular to push further the transverse modal instabilities threshold. Our approach consists in breaking the symmetry of the microstructured fiber cladding for to improve the delocalization of the high order modes outside of the gain medium. Thus, an effective single-mode propagation at a 2μm operating wavelength was first demonstrated into a passive aperiodic fibers whose the core diameter reaches up to 140 μm. After implementing some Stress Applying Parts over our aperiodic design, a PER of 16.5dB was achieved at 2μm using a single polarization passive FA-LPF with a core of 140 μm. Thence, a numerical study on the tailoring the active core refractive index has been carried out so as to fend off the threshold of multimodedness. Additionally, the first LMA Tm-doped fiber (Dcoeur = 18μm) fabricated by the REPUSIL method and showing an efficiency of 50% is demonstrated. Thereafter, the fabrication of the first rod-type Tm-doped FA-LPF with reduced cladding is shown. A 29 μm core FA-LPF was characterized in laser configuration, leading to an effective single-mode emission of 3.8W of average power at 2μm strictly restricted by the available pump power and an efficiency of 20%.

At the Dawn of the 21st century, the field of specialty optical fibers experienced a scientific revolution with the introduction of the stack-and-draw technique, a multi-steps and advanced fiber fabrication method, which enabled the creation of well-controlled micro-structured designs. Since then, an extremely wide variety of finely tuned fiber structures have been demonstrated including novel materials and novel designs. As the complexity of the fiber design increased, highly-controlled fabrication processes became critical. To determine the ability of a novel fiber design to deliver light with properties tailored according to a specific application, several mode analysis techniques were reported, addressing the recurring needs for in-depth fiber characterization. The first part of this dissertation details a novel experiment that was demonstrated to achieve modal decomposition with extended capabilities, reaching beyond the limits set by the existing mode analysis techniques. As a result, individual transverse modes carrying between ~0.01% and ~30% of the total light were resolved with unmatched accuracy. Furthermore, this approach was employed to decompose the light guided in Large-Mode Area (LMA) fiber, Photonic Crystal Fiber (PCF) and Leakage Channel Fiber (LCF). The single-mode performances were evaluated and compared. As a result, the suitability of each specialty fiber design to be implemented for power-scaling applications of fiber laser systems was experimentally determined. The second part of this dissertation is dedicated to novel specialty fiber laser systems. First, challenges related to the monolithic integration of novel and complex specialty fiber designs in all-fiber systems were addressed. The poor design and size compatibility between specialty fibers and conventional fiber-based components limits their monolithic integration due to high coupling loss and unstable performances. Here, novel all-fiber Mode-Field Adapter (MFA) devices made of selected segments of Graded Index Multimode Fiber (GIMF) were implemented to mitigate the coupling losses between a LMA PCF and a conventional Single-Mode Fiber (SMF), presenting an initial 18-fold mode-field area mismatch. It was experimentally demonstrated that the overall transmission in the mode-matched fiber chain was increased by more than 11 dB (the MFA was a 250 ?m piece of 50 ?m core diameter GIMF). This approach was further employed to assemble monolithic fiber laser cavities combining an active LMA PCF and fiber Bragg gratings (FBG) in conventional SMF. It was demonstrated that intra-cavity mode-matching results in an efficient (60%) and narrow-linewidth (200 pm) laser emission at the FBG wavelength. In the last section of this dissertation, monolithic Multi-Core Fiber (MCF) laser cavities were reported for the first time. Compared to existing MCF lasers, renown for high-brightness beam delivery after selection of the in-phase supermode, the present new generation of 7-coupled-cores Yb-doped fiber laser uses the gain from several supermodes simultaneously. In order to uncover mode competition mechanisms during amplification and the complex dynamics of multi-supermode lasing, novel diagnostic approaches were demonstrated. After characterizing the laser behavior, the first observations of self-mode-locking in linear MCF laser cavities were discovered.