Modern gas turbine combustors implement lean premixed (LPM) combustion system to reduce the formation of NOx pollutants. LPM technology has advanced to have the ability to produce extremely low level of NOx emissions. The current focus of research on LPM is focused on reducing the NOx emission to much smaller scales, which is mandated because of the stricter regulations and environmental concerns. However, LPM combustors are susceptible to lean blowout (LBO), and other corresponding instabilities as the combustor is operated lean. Therefore, it is essential to understand the LBO limits and dynamics of flow in lean operating conditions. One of the other primary parameters for the improved combustion chamber designs is an accurate characterization of the heat loads on the liner walls in the wide range of operating conditions. Currently, there are very limited studies on the flame side heat transfer in reacting conditions. Current gas turbine combustion technology primarily focuses on burning natural gas as the gas fuel option for industrial systems. However, interest in utilizing additional options due to environmental regulations as well as concerns about energy security have motivated interest in using fuel gases that have blends of Methane, Propane, H2, CO, CO2, and N2. For example, fuel blends of 35%/60% to 55%/35% of CH4/CO2 are typically seen in Landfill gases. Syngas fuels are typically composed primarily of H2, CO, and N2. Gases from anaerobic digestion of sewage, used commonly in wastewater treatment plants, usually have 65–75% CH4 with the balance being N2. The objective of this study is to understand the LBO limits and the effects of the instabilities that arise (called near blowout oscillations) as the combustor is operated lean. Near blowout oscillations arise as the equivalence ratio is reduced. These oscillations are characterized by continuous blowout and re-ignition events happening at low frequencies. The low-frequency oscillations have very high-pressure amplitude and can potentially damage the liner wall. The impact of the near blowout oscillations on the flow field and heat transfer on the liner walls are studied. To accomplish this, the experiments were conducted at Advanced Propulsion and Power laboratory located at Virginia Tech. A lean premixed, swirl stabilized fuel nozzle designed with central pilot hub was used for the study. Additionally, this work also studies the lean blowout limits with fuel blends of CH4-C3H8, CH4-CO2, and CH4-N2 and also their effect on the stability limits as the pilot fuel percentage was changed. Flow field during near blowout oscillations was studied using planar particle image velocimetry (PIV) and flame shapes and locations during these oscillations was studied by using high-speed imaging of the flame. A statistical tool called proper orthogonal decomposition (POD) was utilized to post-process the PIV data and high-speed imaging data. Heat transfer on the liner walls was studied using a transient IR thermography methodology. The heat transfer on the liner wall during the near blowout instabilities was resolved. LBO limits and near blowout oscillations were characterized by studying the pressure measurements in the primary combustor region. Fluctuating heat loads on the liner walls with the same frequency as that of near blowout instabilities was observed. The magnitude of fluctuation was found to be very high. Phase sorted POD reconstructed flame images demonstrated the location of the flame during near blowout oscillations. Thus, blowout and re-ignition events are resolved from the high-speed flame images. POD reconstructed flow field from the PIV data demonstrated the statistically significant flow structures during near blowout oscillations. A hypothesis for the mechanism of near blowout oscillations was explained based on the measurements and observations made. Lean Blowout limits (LBO) changed when the percentage of pilot and air flow rates was changed. As the pilot percentage increased, LBO limits improved. Results on the study of fuel mixtures demonstrate that the addition of propane, nitrogen and carbon dioxide has minimal effect on when the flame becomes unstable in lean operating conditions. However, on the other hand, the addition of diluent gas showed a potential blowout at higher operating conditions. It was also observed that Wobbe index might not be a good representation for fuels to study the fuel interchangeability in lean operating conditions. / Ph. D.

Lean combustion is increasingly employed in both ground-based gas turbines and aircraft engines for minimizing NOx emissions. Operating under lean conditions increases the risk of Lean Blowout (LBO). Thus LBO proximity sensors, combined with appropriate blowout prevention systems, have the potential to improve the performance of engines. In previous studies, atmospheric pressure, swirl flames near LBO have been observed to exhibit partial extinction and re-ignition events called LBO precursors. Detecting these precursor events in optical and acoustic signals with simple non-intrusive sensors provided a measure of LBO proximity. This thesis examines robust LBO margin sensing approaches, by exploring LBO precursors in the presence of combustion dynamics and for combustor operating conditions that are more representative of practical combustors, i.e., elevated pressure and preheat temperature operation. To this end, two combustors were used: a gas-fueled, atmospheric pressure combustor that exhibits pronounced combustion dynamics under a wide range of lean conditions, and a low NOx emission liquid-fueled lean direct injection (LDI) combustor, operating at elevated pressure and preheat temperature. In the gas-fueled combustor, flame extinction and re-ignition LBO precursor events were observed in the presence of strong combustion dynamics, and were similar to those observed in dynamically stable conditions. However, the signature of the events in the raw optical signals have different characteristics under various operating conditions. Low-pass filtering and a single threshold-based event detection algorithm provided robust precursor sensing, regardless of the type or level of dynamic instability. The same algorithm provides robust event detection in the LDI combustor, which also exhibits low level dynamic oscillations. Compared to the gas-fueled combustor, the LDI events have weaker signatures, much shorter durations, but considerably higher occurrence rates. The disparity in precursor durations is due to a flame mode switch that occurs during precursors in the gas-fueled combustor, which is absent in the LDI combustor. Acoustic sensing was also investigated in both the combustors. Low-pass filtering is required to reveal a precursor signature under dynamically unstable conditions in the gas-fueled combustor. On the other hand in the LDI combustor, neither the raw signals nor the low-pass filtered signals reveal precursor events. The failure of acoustic sensing is attributed in part to the lower heat release variations, and the similarity in time scales for the precursors and dynamic oscillations in the LDI combustor. In addition, the impact of acoustic reflections from combustor boundaries and transducer placement was addressed by modeling reflections in a one-dimensional combustor geometry with an impedance jump caused by the flame. Implementing LBO margin sensors in gas turbine engines can potentially improve time response during deceleration transients by allowing lower operating margins. Occurrence of precursor events under transient operating conditions was examined with a statistical approach. For example, the rate at which the fuel-air ratio can be safely reduced might be limited by the requirement that at least one precursor occurs before blowout. The statistics governing the probability of a precursor event occurring during some time interval was shown to be reasonably modeled by Poisson statistics. A method has been developed to select a lower operating margin when LBO proximity sensors are employed, such that the lowered margin case provides a similar reliability in preventing LBO as the standard approach utilizing a more restrictive operating margin. Illustrative improvements in transient response and reliabilities in preventing LBO are presented for a model turbofan engine. In addition, an event-based, active LBO control approach for deceleration transients is also demonstrated in the engine simulation.

Lean, premixed combustion offers a practical approach for reducing nitrogen oxide (NOx) emissions, but increases the risk of lean blowout (LBO) in gas turbines. Active control techniques are therefore sought which can stabilize a lean flame and prevent LBO. The present work has resulted in the development of flame detection, dynamic modeling, blowout margin estimation, and actuation and control techniques. The flame s acoustic emissions were bandpass filtered at select frequencies to detect localized extinction events, which were found to increase in number near LBO. The lean flame was also found to intermittently burst into a transient tornado configuration in which the flame s inner recirculation zone would collapse. The localized extinctions were dynamically linked to the tornado bursts using a linear, first order model. The model was subsequently applied to predict tornado bursts based on optically detected localized extinction events. It was found that both localized extinctions and tornado bursts are by themselves Poisson processes; the exponential distribution of their spacing times could be used to determine blowout probability. Blowout mitigation was achieved by redistributing the fuel flow between the annular swirlers and central preinjection pilot, both of which were premixed. Rule-based and lead-lag control architectures were developed and validated.

This thesis describes an experimental investigation of lean blowoff for H2/CO/CH4 mixtures in a swirling combustor. This investigation consisted of three thrusts. The first thrust focused on correlations of the lean blowoff limits of H2/CO/CH4 mixtures under different test conditions. It was found that a classical Damköhler number approach with a diffusion correction could correlate blowoff sensitivities to fuel composition over a range of conditions. The second part of this thesis describes the qualitative flame dynamics near blowoff by systematically characterizing the blowoff phenomenology as a function of hydrogen level in the fuel. These near blowoff dynamics are very complex, and are influenced by both fluid mechanics and chemical kinetics; in particular, the role of thermal expansion across the flame and extinction strain rate were suggested to be critical in describing these influences. The third part of this thesis quantitatively analyzed strain characteristics in the vicinity of the attachment point of stable and near blowoff flames. Surprisingly, it was found that in this shear layer stabilized flame, flow deceleration is the key contributor to flame strain, with flow shear playing a relatively negligible role. Near the premixer exit, due to strong flow deceleration, the flame is negatively strained i.e., compressed. Moving downstream, the strain rate increases towards zero and then becomes positive, where flames are stretched. As the flame moves toward blowoff, holes begin to form in the flame sheet, with a progressively higher probability of occurrence as one moves downstream. It is suggested that new holes form with a more uniform probability, but that this behavior reflects the convection of flame holes downstream by the flow. It has been shown in prior studies, and affirmed in this work, that flames approach blowoff by first passing through a transient phase manifested by local extinction events and the appearance of holes on the flame. A key conclusion of this work is that the onset of this boundary occurs at a nearly constant extinction strain rate. As such, it is suggested that Damköhler number scalings do not describe blowoff itself, but rather the occurrence of this first stage of blowoff. Given the correspondence between this first stage and the actual blowoff event, this explains the success of classical Damköhler number scalings in describing blowoff, such as shown in the first thrust of this thesis. The physics process associated with the actual blowoff event is still unclear and remains a key task for future work.

No description available.

No description available.

Mixtures of ammonia and hydrogen have received significant interest recently as a possible replacement for hydrocarbon fuels. A toroidal jet-stirred reactor (TJSR) was designed and constructed to combust these mixtures in the well-stirred limit for validating chemical kinetic mechanisms and improving the current understanding of the combustion properties of this fuel. The TJSR was designed to achieve low residence times – on the order of 5 ms – to approximate the conditions in an aircraft gas turbine combustor. Simulations were conducted to determine mass flow rates, expected emissions output, and expected lean blow out. Based on these results, material studies were conducted to determine the best materials for each of the TJSR's components. Thermomechanical were conducted to determine the expected temperature distribution and thermal expansion during operation. Casing components were designed to seal the gases in the reactor as well as provide means to connect it to a pressure vessel or other piping. This work will allow for chemical mechanism validation of lean blowout in ammonia-hydrogen mixtures while laying the foundation for future high-pressure testing of such mixtures up to 60 bar.

This thesis describes an investigation on the blowout phenomenon in gas turbine combustors. The combustor primarily used for this study was a swirl- and dump-stabilized, atmospheric pressure device, which did not exhibit dynamic combustion instabilities. The first part of the thesis work concentrated on finding a sensing methodology to be able to predict the onset of approach of combustor blowout using optical methods. Temporary extinction-reignition events that occurred prior to blowout were found to be precursor events to blowout. A threshold based method was developed to identify these events in the time-resolved sensor output. The number and the average length of each event were found to increase as the LBO limit (fuel-air ratio) is approached. This behavior is used to predict the proximity to lean blowout. In the second part of this study, the blowout sensor was incorporated into a control system that monitored the approach of blowout and then actuated an alternate mechanism to stabilize the combustor near blowout. Enhanced stabilization was achieved by redirecting a part of the main fuel to a central preinjection pilot injection. The sensing methodology, without modification, was effective for the combustor with pilot stabilization. An event based control algorithm for controlling the combustor from blowing out was also developed in this study. The control system was proven to stabilize the combustor even when the combustor loading was rapidly changed. The final part of this study focused on understanding the physical mechanisms behind the precursor events. High speed movies of flame chemiluminescence and laser sheet scattering from oil droplets seeded into the reactants were analyzed to explain the physical processes that cause the extinction and the reignition of the combustor during a precursor event. A physical model for coupling of the fluid dynamics of vortex breakdown and combustion during precursor and blowout events is proposed. This model of blowout phenomenon, along with the sensing and control strategies developed in this study could enable the gas turbine combustor designers to design combustors with wider operability regimes. This could have significant payoffs in terms of reduction in NOx emissions from the combustor.

<div>The aviation industry is continuously growing amid tight restrictions on global emission</div><div>reductions. Alternative aviation fuels have gained attention and developed to replace the</div><div>conventional petroleum-derived aviation fuels. The replacement of conventional fuels with</div><div>alternative fuels, which are composed solely of hydrocarbons (non-petroleum), can mitigate</div><div>impacts on the environment and diversify the energy supply, potentially reducing fuel costs.</div><div>To ensure the performance of alternative fuels, extensive laboratory and full-scale engine</div><div>testings are required, thereby a lengthy and expensive process. The National Jet Fuel Combustion</div><div>Program (NJFCP) proposed a plan to reduce this certification process time and</div><div>the cost dramatically by implementing a computational model in the process, which can be</div><div>replaced with some of the testings. This requires an understanding of the influence of chemical/</div><div>physical properties of alternative fuels on combustion performance. The main objective</div><div>of this work is to investigate the spray characteristics of alternative aviation fuels compared</div><div>to that of conventional aviation fuels, which have been characterized by different physical</div><div>liquid properties at different gas turbine-relevant conditions.</div><div>The experimental work focuses on the spray characteristics of standard and alternative</div><div>aviation fuels at three operating conditions such as near lean blowout (LBO), cold engine</div><div>start, and high ambient pressure conditions. The spray generated by a hybrid pressureswirl</div><div>airblast atomizer was investigated by measuring the drop size and drop velocity at</div><div>a different axial distance downstream of the injector using a phase Doppler anemometry</div><div>(PDA) measurement system. This provided an approximate trajectory of the largest droplet</div><div>as it traveled down from the injector. At LBO conditions, the trend of decreasing drop size</div><div>and increasing drop velocity with an increase in gas pressure drop was observed for both</div><div>conventional (A-2) and alternative aviation fuels (C-1, C-5, C-7, and C-8), while the effect of</div><div>fuel injection pressure on the mean drop size and drop velocity was observed to be limited.</div><div>Moreover, the high-speed shadowgraph images were also taken to investigate the effect of</div><div>the pressure drop and fuel injection pressures on the cone angles. Their effects were found</div><div>to be limited on the cone angle.</div><div><div>The spray characteristics of standard (A-2 and A-3) and alternative (C-3) fuels were</div><div>investigated at engine cold-start conditions. At such a crucial condition, sufficient atomization</div><div>needs to be maintained to operate the engine properly. The effect of fuel properties,</div><div>especially the viscosity, was investigated on spray drop size and drop velocity using both</div><div>conventional and alternative aviation fuels. The effect of fuel viscosity was found to be minimal</div><div>and dominated by the effect of the surface tension, even though it showed a weak trend</div><div>of increasing drop size with increasing surface tension. The higher swirler pressure drop</div><div>reduced the drop size and increased drop velocity due to greater inertial force of the gas for</div><div>both conventional and alternative aviation fuels at the cold start condition. However, the</div><div>effect of pressure drop was observed to be reduced at cold start condition compared to the</div><div>results from the LBO condition.</div><div>The final aspect of experimental work focuses on the effect of ambient pressures on the</div><div>spray characteristics for both conventional (A-2) and alternative (C-5) aviation fuels. Advanced</div><div>aviation technology, especially in turbomachinery, has resulted in a greater pressure</div><div>ratio in the compressor; therefore, greater pressure in combustors for better thermal efficiency.</div><div>The effect of ambient pressure on drop size, drop velocity, and spray cone angle was</div><div>investigated using the PDA system and simultaneous Planar Laser-Induced Fluorescence</div><div>(PLIF) and Mie scattering measurement. A significant reduction in mean drop size was</div><div>observed with increasing ambient pressure, up to 5 bar. However, the reduction in the mean</div><div>drop size was found to be limited with a further increase in the ambient pressure. The effect</div><div>of the pressure drop across the swirler was observed to be significant at ambient pressure of</div><div>5 bar. The spray cone angle estimation at near the swirler exit and at 25.4 mm downstream</div><div>from the swirler exit plane using instantaneous Mie images was found to be independent of</div><div>ambient pressure. However, the cone angle at measurement plane of 18 mm in the spray</div><div>was observed to increase with increasing ambient pressure due to entrainment of smaller</div><div>droplets at higher ambient pressure. Furthermore, the fuel droplet and vapor distribution in</div><div>the spray were imaged and identified by comparing instantaneous PLIF and Mie images.</div><div>Lastly, a semi-empirical model was also developed using a phenomenological three-step</div><div>approach for the atomization process of the hybrid pressure-swirl airblast atomizer. This</div><div>model includes three sub-models: pressure-swirl spray droplet formation, droplet impingement, and film formation, and aerodynamic breakup. The model predicted drop sizes as a</div><div>function of ALR, atomizing gas velocity, surface tension, density, and ligament length and</div><div>diameter and successfully demonstrated the drop size trend observed with fuel viscosity,</div><div>surface tension, pressure drop, and ambient pressure. The model provided insights into the</div><div>effect of fuel properties and engine operating parameters on the drop size. More experimental</div><div>work is required to validate the model over a wider range of operating conditions and</div><div>physical fuel properties.</div><div>Overall, this work provides valuable information to increase understanding of the spray</div><div>characteristics of conventional and alternative aviation fuels at various engine operating</div><div>conditions. This work can provide valuable data for developing an advanced computational</div><div>combustor model, ultimately expediting the certification of new alternative aviation fuels.</div></div>

No description available.