A 50 MHz Frequency Modulated Continuous Wave (FMCW) radar system, developed at the University of Saskatchewan to provide improved spatial and temporal resolution measurements of auroral E-region plasma processes, introduces ambiguous spectral information, due to spectral ghosting, for scattering events in which multiple radar echoes are detected. This thesis identifies two Linearly Frequency Modulated (LFM) radar waveforms used by the FMCW system as the source of the ghosting. An analysis procedure designed to counteract the spectral ghosting problem is developed but is not an ideal solution, and therefore replacement of the LFM waveforms is recommended.<p> A detailed investigation of alternative radar waveforms using the Ambiguity Function and Ambiguity Diagram techniques is performed. A frequency coded continuous wave radar waveform based on a composite Costas sequence is proposed as a successor to the LFM waveforms. The composite Costas radar waveform will conserve the spatial and temporal resolutions extended by the LFM waveforms and preclude any spectral ghosting. Implementing the proposed radar waveform and avoiding receiver saturation issues with the mono-static FMCW radar system in which both the transmitting and receiving antenna arrays are simultaneously and continuously active and geographically co-located is also discussed.<p> In addition to this, two 50 MHz backscatter events are presented in this thesis to demonstrate the effectiveness of the FMCW system, notwithstanding the spectral ghosting complication. The first event from November 21, 2009 is identified as a Type 1 instability and the second from September 13, 2009 is identified as a Type 2 instability which lasted for ~ 16 minutes. Linear plasma fluid theory is used to provide a brief interpretation of both scattering events.

In this thesis, the geometric margin is used for the first time as the robustness indicator of an uncoupled cellular neural network implementing a given Boolean function. First, robust template design for uncoupled cellular neural networks implementing linearly separable Boolean functions by support vector machines is proposed. A fast sequential minimal optimization algorithm is presented to find maximal margin classifiers, which in turn determine the robust templates. Some general properties of robust templates are investigated. An improved CFC algorithm implementing an arbitrarily given Boolean function is proposed. Two illustrative examples are provided to demonstrate the validity of the proposed method.

In this thesis, we investigate the use of adaptive antenna algorithms for OFDM systems to suppress interference in various channel conditions including narrowband and wideband interference, flat and frequency selective fading. We propose a novel frequency-domain beamformer, based on the linearly constrained modified constant modulus hybrid LMS (LCMCM-HLMS) algorithm for OFDM systems to improve the performance of interference suppression in AWGN channel with narrowband interference, Rayleigh fast fading channel with phase distortion, and the multipath environment. To verify the merits of the frequency-domain beamformer, the effect due to narrowband interference and random phase distortion are investigated. Moreover, to improve the performance of adaptive beamforming algorithm, the frequency-domain linearly constrained modified constant modulus hybrid LMS (LCMCM-HLMS) algorithm is proposed. Computer simulation results show that the proposed frequency-domain LCMCM-HLMS beamformer has good capability of interference supression in various environment, and can mitigate the phase distortion of channel. However, in the time-domain beamformer based on LMS [33], RLS ,LC-LMS and LC-FLS algorithm for OFDM systems, the performance may severely degraded under some situations. We will show that in terms of output SINR, beampatern, received signal constellation and mean square error (MSE), for narrowband interference suppression in AWGN channel, phase distortion in Rayleigh fast fading channel and the multipath environment.

An ID generating circuit is unquestionably the core of a chipless RFID tag. For convenience of printing process and cost consideration, the circuit should be kept as simple as possible. Based on the cognition, an 8-bit time-domain based ID generating circuit that merely consists of a ML and eight capacitors was offered, and implemented on photo-paper substrates via inkjet printing process. In addition to the experimental measurements, the circuit was also input into circuit simulators for cross-validation. The good agreement between simulations and measurements is observed, exhibiting the tag technical feasibility. Besides of low cost, the tag has wide compatibility with current licensed RFID spectrum, which will facilitate the future deployment in real applications. Compared   to  time-domain   based  chipless   tags,  frequency   signatures   based chipless RFID tags are expected to offer a larger coding capacity. As a response, we presented a 10-bit frequency-domain based chipless RFID tag. The tag composed of ten configurable LC resonators was implemented on flexible polyimide substrate by using  fast  toner-transferring  process.  Field  measurements  revealed  not  only  the practicability  of  the  tag,  but  also  the  high  signal  to  noise  ratio  (SNR).  Another frequency domain tag consists of a configurable coplanar LC resonator. With the use of all printing process, the tag was for the first time realized on common packaging papers.  The tag feasibility was confirmed by subsequent measurements. Owing to the ultra-low cost potential and large SNR, The tag may find wide applications in typical RFID solutions such as management of paper tickets for social events and governing of smart documents. Ultra wide band (UWB) technology possesses a number of inherent merits such as high speed communication and large capacity, multi-path immunity, accurate ranging and positioning, penetration through obstacles, as well as extremely low-cost and low- power transmitters. Thus, passive UWB RFIDs are expected to play an important pole in  the future identification applications for IoT. We explained the feature difference between  UWB  chipless  tags  and  chip  based  tags,  and  forecasted  the  applications respectively  based on the comparison  between the two technologies.  It is expected that the two technologies will coexist and compensate each other in the applications of IoT. Lastly, the thesis ends up with brief summary of the author’s contributions, and technical prospect for the future development of printable chipless RFID tags. / <p>QC 20140304</p>

O problema de minimização com restrições lineares e importante, não apenas pelo problema em si, que surge em várias áreas, mas também por ser utilizado como subproblema para resolver problemas mais gerais de programação não-linear. GENLIN e um método eficiente para minimização com restrições lineares para problemas de pequeno e médio porte. Para que seja possível a implementação de um método similar para grande porte, é necessário ter um método eficiente, também para grande porte, para projeção de pontos no conjunto de restrições lineares. O problema de projeção em um conjunto de restrições lineares pode ser escrito como um problema de programação quadrática convexa. Neste trabalho, estudamos e implementamos métodos esparsos para resolução de problemas de programação quadrática convexa apenas com restrições de caixa, em particular o clássico método Moré-Toraldo e o \"método\" NQC. O método Moré-Toraldo usa o método dos Gradientes Conjugados para explorar a face da região factível definida pela iteração atual, e o método do Gradiente Projetado para mudar de face. O \"método\" NQC usa o método do Gradiente Espectral Projetado para definir em que face trabalhar, e o método de Newton para calcular o minimizador da quadrática reduzida a esta face. Utilizamos os métodos esparsos Moré-Toraldo e NQC para resolver o problema de projeção de GENLIN e comparamos seus desempenhos / The linearly constrained minimization problem is important, not only for the problem itself, that arises in several areas, but because it is used as a subproblem in order to solve more general nonlinear programming problems. GENLIN is an efficient method for solving small and medium scaled linearly constrained minimization problems. To implement a similar method to solve large scale problems, it is necessary to have an efficient method to solve sparse projection problems onto linear constraints. The problem of projecting a point onto a set of linear constraints can be written as a convex quadratic programming problem. In this work, we study and implement sparse methods to solve box constrained convex quadratic programming problems, in particular the classical Moré-Toraldo method and the NQC \"method\". The Moré-Toraldo method uses the Conjugate Gradient method to explore the face of the feasible region defined by the current iterate, and the Projected Gradient method to move to a different face. The NQC \"method\" uses the Spectral Projected Gradient method to define the face in which it is going to work, and the Newton method to calculate the minimizer of the quadratic function reduced to this face. We used the sparse methods Moré-Toraldo and NQC to solve the projection problem of GENLIN and we compared their performances

Die Beeinflussung optischer Eigenschaften durch Bestrahlung stellt eine Grundlage für die Herstellung anisotroper optischer Komponenten dar. In dünnen Schichten von Azobenzen-Polymeren kann optische Anisotropie durch linear polarisierte Bestrahlung induziert oder modifiziert werden. Ziel der Arbeit war es, wesentliche Struktur-Eigenschafts-Beziehungen zum Prozess der Photoorientierung zu erarbeiten, um so eine Optimierung der Materialien für verschiedene Anwendungen ermöglichen. <br><br> In isotropen Schichten flüssigkristalliner und amorpher Azobenzen-Polymeren wird das Ausmaß der induzierten optischen Anisotropie günstig durch eine Donor/Akzeptor-Substitution in 4,4'-Position beeinflusst. Die Induktionsgeschwindigkeit ist in Schichten flüssigkristalliner Polymeren deutlich geringer, jedoch lassen sich höhere Werte der Doppelbrechung und des Dichroismus erreichen. In Copolymeren bewirkt die Photoorientierung der Azobenzen-Seitengruppen eine kooperative Orientierung von formanisotropen Seitengruppen. Die Mesogenität der nicht-photochromen Seitengruppen erhöht das Ausmaß der induzierten optischen Anisotropie. Die Stabilität der induzierten Doppelbrechung und des Dichroismus wird durch diese Gruppen gesteigert. <br><br> In Schichten flüssigkristalliner Polymeren wird die induzierte optische Anisotropie beim Tempern im Bereich der Mesophasen erheblich verstärkt. Dabei reicht ein geringes Maß an induzierter Anisotropie aus, um Doppelbrechungs- und Dichroismuswerte zu erzielen, wie sie für LC-Domänen typisch sind. <br><br> In orientierten Schichten von Azobenzen-Polymeren wird das Resultat der linear polarisierten Bestrahlung durch die Stärke der anisotropen Wechselwirkungen in den flüssigkristallinen Domänen oder den LB-Multilayern bestimmt. Eine lichtinduzierte Reorientierung kann nur erreicht werden, wenn diese Wechselwirkungen überwunden werden können. Erfolgt eine Photoreorientierung in den orientierten Polymerschichten, werden in Copolymeren formanisotrope Seitengruppen ebenfalls kooperativ reorientiert. Eine vorgelagerte UV-Bestrahlung kann durch Erzeugung eines hohen Anteils an nicht-mesogenen Z-Isomeren die anisotropen Wechselwirkungen stark schwächen und so die Seitengruppen entkoppeln. Aus diesem Zustand erfolgt die Photoreorientierung mit einer der Photoorientierung in isotropen Schichten vergleichbaren Effizienz. <br><br> Die erarbeiteten Struktur-Eigenschafts-Beziehungen liefern einen Beitrag zur Optimierung derartiger Materialien für Anwendungen in den Bereichen optischer Funktionsschichten, holographischer Datenspeicherung oder der Generierung von Oberflächenreliefgittern. / The modification of optical characteristics by irradiation represents a basis for the creation of anisotropic optical components. In thin films of azobenzene polymers optical anisotropy can be induced or modified by linearly polarized irradiation. The goal of the work was it to compile substantial structure property relations of the photoorientation process in order to support an optimization of the materials for different applications. <br><br> In isotropic films of liquid crystalline and amorphous azobenzene polymers the extent of the induced optical anisotropy is increased by a donor/acceptor substitution in 4,4'-position. The induction speed is clearly smaller in films of liquid crystalline polymers, however higher values of birefringence and dichroism can be reached. In copolymers the photoorientation of the azobenzene side groups causes a cooperative orientation of form-anisotropic side groups. The mesogenity of the non-photochromic side groups increases the extent of the induced optical anisotropy. <br><br> The stability of the induced birefringence and dichroism is increased by these groups considerably. In films of liquid crystalline polymers the induced optical anisotropy is substantially amplified on annealing within the range of the mesophases. In this way, a small ratio of induced anisotropy is sufficient, in order to obtain birefringence and dichroism values as typical for LC domains. <br><br> In oriented films of azobenzene polymers the result of the linear polarized irradiation is determined by the strength of the anisotropic interactions in the liquid crystalline domains or the LB multilayers. A light-induced reorientation can be only achieved, if these interactions can be overcome. If a photoreorientation takes place in the oriented layers of copolymers, form-anisotropic side groups are cooperatively reoriented. An initial UV irradiation can strongly weaken the anisotropic interactions by generating of a high fraction of non-mesogenic z-isomers and decouples in this way the side groups. From this state the photoreorientation proceeds with an efficiency one comparable to the photoorientation in isotropic films. <br><br> The compiled structure property relations supplies a contribution for the optimization of such materials for applications in the fields of optical function films, holographic data storage or the generation of surface relief gratings.

ABSTRACT 3-D SOIL STRUCTURE INTERACTION ANALYSES OF THREE IDENTICAL BUILDINGS IN SAKARYA CITY AFTER 17 AUGUST 1999 KOCAELI EARTHQUAKE &Uuml / nal,Orhan M.S., Department of Civil Engineering, Supervisor: Assist. Prof. Dr Kemal &Ouml / nder &Ccedil / etin October 2003, 116 Pages The aim of this study is to analyze the soil structure interaction of three identical buildings on &ordf / ahinler Street of Sakarya city which had no damage to heavy damage after the Kocaeli (1999) earthquake. For the purpose of 3-D dynamic nonlinear analysis of the soil site and the overlying structures, Flac3D software was chosen as the numerical modeling framework. Soil properties were determined by using the results of available site investigation studies. A three dimensional mesh was created to represent the topographic and geometric constraints of the problem. Linearly elastic perfectly plastic constitutive model was implemented to model the soil behavior. The results of 3-D dynamic numerical analyses in the forms of acceleration, displacement, strain, stress and pore pressure were presented. The higher acceleration, strain and stress levels calculated under the collapsed building can be attributed as the major cause of poor performance of the structure.

In this thesis, the problem of multiple access interference (MAI) suppression for the multi-carrier (MC) code division multiple access (CDMA) system, based on the multi-carrier modulation with modified Gaussian wavelet, associated with the combining process is investigated for Rayleigh fading channel. The main concern of this thesis is to derive a new scheme, based on the linearly constrained constant modulus (LCCM) criterion with the robust inverse QR decomposition (IQRD) recursive least squares (RLS) algorithm to improve the performance of the wavelet-based MC-CDMA system with combining process. To verify the merits of the new algorithm, the effect due to imperfect channel parameters estimation and near-far effect are investigated. We show that the proposed robust LCCM IQRD-RLS algorithm outperforms the conventional LCCM-gradient algorithm, in terms of output SINR, for MAI suppression under channel mismatch environment. Also, the performance of the modified Gaussian wavelet-based MC-CDMA system is superior to the one with wavelet-based MC-CDMA system. It is more robust to the channel mismatch and near-far effect. Moreover, the modified Gaussian wavelet-based MC-CDMA system with robust LCCM IQRD-RLS algorithm does have better performance over other conventional approaches, such as the LCCM-gradient algorithm, maximum ratio combining (MRC), and blind adaptation algorithm, in terms of the capability of MAI suppression and bit error rate (BER).

We derive basic properties of groups which can be approximated with matrices. These include closure of classes of such groups under group theoretic constructions including direct and inverse limits and free products. We show that metric ultraproducts of projective linear groups over fields of different characteristics are not isomorphic. We further prove that the lattice of normal subgroups in ultraproducts of compact simple groups is distributive. It is linearly ordered in the case of finite simple groups or Lie groups of bounded rank.

Notre étude vise à améliorer la compréhension des modes de rotation continue d’une détonation. Elle porte sur leur caractérisation dans une chambre annulaire de section,normale à son axe de révolution, constante ou linéairement croissante. Le principe de fonctionnement repose sur l’injection continue de gaz frais devant le front de détonation pour renouveler la couche réactive et entretenir sa propagation. Ce travail trouve son application dans le développement de systèmes propulsifs utilisant la détonation rotative comme mode de combustion (Rotating Detonation Engine, RDE). Nous avons conçu et réalisé un banc expérimental dont l’élément principal est une chambre annulaire de diamètre intérieur 50 mm, de longueur 90 mm et d’épaisseur 5 ou 10 mm. Elle peut être équipée de noyaux cylindrique ou conique, de longueurs comprises entre 12 mm et 90mm et, pour les cônes, de demi-angles au sommet compris entre 0± et 14.6±. Elle est alimentée par des injections séparées de carburant, l’éthylène, et d’oxydant, formé ici par un mélange d’oxygène et d’azote. Plusieurs concentrations d’azote ont été considérées de manière à étudier plusieurs détonabilités de mélange. La caractérisation des régimes de détonation, de leurs célérités et de leurs pressions, est fondée sur l’analyse de signaux de capteurs de pression dynamiques et sur des visualisations par caméras ultrarapides. Nos résultats expérimentaux détaillent la phase d’amorçage, les modes de combustion et leur stabilité. L’étude paramétrique, réalisée pour plusieurs détonabilités, débits massiques et géométries internes de la chambre, met en évidence que, si les deux premiers paramètres n’ont pas d’effet notable sur les célérités et les pressions des modes de détonation,la géométrie interne de la chambre joue, elle, un rôle majeur dans l’amélioration de ces caractéristiques, en particulier la diminution de la longueur du noyau et l’augmentation de sa conicité (de son demi-angle au sommet). Nous avons réalisé une étude numérique afin d’expliquer les déficits mesurés de célérité et de pression. Elle met en avant la dégradation des propriétés théoriques de détonation résultant de la dilution et du réchauffement des réactifs par les produits de détonation. Nous proposons également un calcul du rendement thermodynamique qui, à la différence de modélisations antérieures, prend en compte la structure d’une détonation rotative. Nous décrivons aussi un calcul de hauteur de front de détonation pour les modes et géométries de chambre considérés dans cette thèse. Notre étude démontre ainsi l’intérêt de futures recherches sur la géométrie interne des chambres annulaires à détonation rotative et sur la prise en compte des phénomènes à l’origine des pertes d’efficacité. / Our study aims at improving the understanding of how a detonation may continuously rotate. It is focused on rotation modes in an annular chamber with constant or linearly increasing normal section. The functioning principle is based on the continuous injection of fresh reactive gases so as to regenerate a reactive layer ahead of the detonation front and maintain sufficient conditions for detonation propagation. The main incentive of the work is the development of propulsive devices that use detonation as the combustion mode (Rotating Detonation Engine, RDE). We have designed and built an experimental test bench of which the main part is an annular chamber with inner diameter 50 mm length 90 mm, and thickness 5 or 10 mm. The chamber can be equipped with cylindrical or conical kernels with lengths ranging between 12 mm and 90 mm and, for the conical kernels, with the apex half-angles ranging between 0± and 14.6±. The fuel is ethylene and the oxidizer is a mixture of oxygen and nitrogen, and they are injected separately in the chamber. We have considered several nitrogen concentrations so as to vary the reactive mixture detonability. The characterizations of the detonation regimes, velocities and pressures are based upon the analyses of signals from pressure transducers and of direct light visualizations from high-speed cameras. Our experimental results detail the ignition phase, the combustion modes and their stability. We have carried out experiments with several detonabilities, mass-flow rates and kernel geometries. Our main finding is that modifying the kernel geometry, specifically decreasing the kernel length and increasing its conicity (the apex half-angle) significantly improve detonation velocities and pressures, unlike the first two parameters that have much lesser influences, in our conditions. We have conducted a numerical analysis that suggests that dilution and heating of the fresh gases by detonation products explain the measured deficits of pressure and velocity. We have presented a calculation of thermodynamic efficiency which, contrary to former modeling includes a more realistic structure of rotating detonation.We have proposed a calculation of detonation-front height for the rotation modes and the chamber geometries in this work. Our study thus demonstrates the interest in further research work on inner geometry of rotating-detonation chambers and on phenomena that may be responsible for efficiency losses.