It is the responsibility of pavement engineers to design pavements that provide safe and smooth riding surfaces over their entire life cycle. Each year many people around the world lose their lives in vehicle crashes, which are one of the leading causes of death in the United States (US). One of the contributing factors in many of these crashes is inappropriate friction between tires and the pavement. To minimize the impact of this factor, state Departments of Transportation (DOTs) must monitor the friction of their pavement networks systematically and regularly. Several devices are used around the world for measuring friction. Locked-wheel skid trailers are the predominant technology for roadways in the U.S. However, Continues Friction Measuring Equipment (CFME) is emerging as a practical alternative, especially for network-level monitoring. This type of technology has been used for monitoring runway friction for many years and is starting to be used also for measuring roadway friction. This thesis evaluates the different operational characteristics of CFME to provide guidelines for highway agencies interested in using this technology for supporting their friction management programs. It follows a manuscript format and is composed of two papers. The first part of the thesis presents a methodology to objectively synchronize and compare CFME measurements using cross-correlation. This methodology allows for comparing the “shape” of the friction profiles, instead of only the average friction values. The methodology is used for synchronizing friction measurements and assessing the repeatability and reproducibility of the CFME using friction measurements taken on a wide range of surfaces at the Virginia Smart Road. The proposed approach provides highway agencies with a rigorous method to process CFME measurements. The second part of the thesis evaluates the impact of several operational characteristics on the CFME measurements using a field experiment. The results of the experiment confirmed that the measurements are significantly affected by (1) the direction of testing while testing on sections of road with a significant grade, (2) water film thickness, and (3) testing speed. The experiment showed that measurements taken downhill on a 6% grade were significantly higher than those taken uphill. The analysis also verified that, consistent with previous studies, the measured friction decreases with higher water depth and testing speeds. It also showed that the change of friction with speed is approximately linear over the range of speeds used in the experiment. In general, the thesis results suggest that CFME can provide repeatable and reproducible friction profiles that can be used to support friction management programs and other asset management business functions. However, care should be taken with regard to the operational conditions during testing since the measurements are affected by several factors. Further research is needed to (1) quantify the effect of these, and potentially other, operational factors; and (2) establish standard testing condition and approaches for correcting measurements taken under other conditions. / Master of Science

Friction is one of the essential aspects of pavement performance and safety. Unfortunately, the rate at which the friction data are being collected exceeds the rate at which the data can be proficiently analyzed. Furthermore, the Utah Department of Transportation (UDOT) lacks long-term trend analysis for the many years of locked-wheel skid trailer (LWST) data collected in Utah. In addition, UDOT is missing a statistically adequate correlation equation between friction-testing devices. Likewise, only one method is used in Utah to prequalify aggregates for use in pavements. Finally, there has not been an investigation of the potential use of lithium silicate solution in Utah as a hardening agent to decrease the rate of friction loss. This research consists of five objectives. The first objective was to investigate pavement friction factors that influence skid resistance; methods of measuring skid resistance in the laboratory and the field, including correlations between test results; methods of evaluating aggregate sources; and methods of enhancing skid resistance of asphalt pavements through a comprehensive literature review on these subjects. The second objective was to investigate temporal trends in skid numbers measured using the LWST on Utah highways with different surface treatment types. The third objective was to develop a three-way correlation between the skid number measured with the LWST in the field, the British pendulum number measured with the British pendulum tester (BPT) in the field, and the polish value measured with the BPT in the laboratory. The fourth objective was to investigate selected performance-related properties of aggregates used to produce surface treatments at several field sites representing Utah conditions. The fifth objective was to examine the potential benefits of lithium silicate treatment for improving the resistance of aggregates to polishing. The scope of the research for the five objectives included statistical analysis, field testing, and laboratory experimentation. The findings include, first, a literature review that identified four critical deficiencies in Utah’s friction-related literature, which formed the basis of the remaining four objectives. Second, a statistical analysis of 9 years of LWST data indicated above-average skid values across Utah’s pavement network. Third, correlations were evaluated for multiple friction-testing devices. Fourth, X-ray diffraction testing methods were found to compare favorably to the accelerated polish test. Fifth and finally, the effects of lithium silicate solution on polish-susceptible aggregates were documented. This research has substantially advanced the body of knowledge on pavement friction testing and improving the resistance of aggregates to polishing in Utah through laboratory and field experimentation