Knowledge on how ligaments and articular surfaces guide passive motion at the human ankle joint complex is fundamental for the design of relevant surgical treatments. The dissertation presents a possible improvement of this knowledge by a new kinematic model of the tibiotalar articulation. In this dissertation two one-DOF spatial equivalent mechanisms are presented for the simulation of the passive motion of the human ankle joint: the 5-5 fully parallel mechanism and the fully parallel spherical wrist mechanism. These mechanisms are based on the main anatomical structures of the ankle joint, namely the talus/calcaneus and the tibio/fibula bones at their interface, and the TiCaL and CaFiL ligaments. In order to show the accuracy of the models and the efficiency of the proposed procedure, these mechanisms are synthesized from experimental data and the results are compared with those obtained both during experimental sessions and with data published in the literature. Experimental results proved the efficiency of the proposed new mechanisms to simulate the ankle passive motion and, at the same time, the potentiality of the mechanism to replicate the ankle’s main anatomical structures quite well. The new mechanisms represent a powerful tool for both pre-operation planning and new prosthesis design.

Porous materials are widely used in many fields of industrial applications, to achieve the requirements of noise reduction, that nowadays derive from strict regulations. The modeling of porous materials is still a problematic issue. Numerical simulations are often problematic in case of real complex geometries, especially in terms of computational times and convergence. At the same time, analytical models, even if partly limited by restrictive simplificative hypotheses, represent a powerful instrument to capture quickly the physics of the problem and general trends. In this context, a recently developed numerical method, called the Cell Method, is described, is presented in the case of the Biot's theory and applied for representative cases. The peculiarity of the Cell Method is that it allows for a direct algebraic and geometrical discretization of the field equations, without any reduction to a weak integral form. Then, the second part of the thesis presents the case of interaction between two poroelastic materials under the context of double porosity. The idea of using periodically repeated inclusions of a second porous material into a layer composed by an original material is described. In particular, the problem is addressed considering the efficiency of the analytical method. A analytical procedure for the simulation of heterogeneous layers based is described and validated considering both conditions of absorption and transmission; a comparison with the available numerical methods is performed. ---------------- I materiali porosi sono ampiamente utilizzati per diverse applicazioni industriali, al fine di raggiungere gli obiettivi di riduzione del rumore, che sono resi impegnativi da norme al giorno d'oggi sempre più stringenti. La modellazione dei materiali porori per applicazioni vibro-acustiche rapprensenta un aspetto di una certa complessità. Le simulazioni numeriche sono spesso problematiche quando siano coinvolte geometrie di pezzi reali, in particolare riguardo i tempi computazionali e la convergenza. Allo stesso tempo, i modelli analitici, anche se parzialmente limitati a causa di ipotesi semplificative che ne restringono l'ambito di utilizzo, rappresentano uno strumento molto utile per comprendere rapidamente la fisica del problema e individuare tendenze generali. In questo contesto, un metodo numerico recentemente sviluppato, il Metodo delle Celle, viene descritto, implementato nel caso della teoria di Biot per la poroelasticità e applicato a casi rappresentativi. La peculiarità del Metodo delle Celle consiste nella discretizzazione diretta algebrica e geometrica delle equazioni di campo, senza alcuna riduzione a forme integrali deboli. Successivamente, nella seconda parte della tesi viene presentato il caso delle interazioni tra due materiali poroelastici a contatto, nel contesto dei materiali a doppia porosità. Viene descritta l'idea di utilizzare inclusioni periodicamente ripetute di un secondo materiale poroso all'interno di un layer a sua volta poroso. In particolare, il problema è studiando il metodo analitico e la sua efficienza. Una procedura analitica per il calcolo di strati eterogenei di materiale viene descritta e validata considerando sia condizioni di assorbimento, sia di trasmissione; viene effettuata una comparazione con i metodi numerici a disposizione.

Dielectric Elastomers (DE) are incompressible dielectrics which can experience deviatoric (isochoric) finite deformations in response to applied large electric fields. Thanks to the strong electro-mechanical coupling, DE intrinsically offer great potentialities for conceiving novel solid-state mechatronic devices, in particular linear actuators, which are more integrated, lightweight, economic, silent, resilient and disposable than equivalent devices based on traditional technologies. Such systems may have a huge impact in applications where the traditional technology does not allow coping with the limits of weight or encumbrance, and with problems involving interaction with humans or unknown environments. Fields such as medicine, domotic, entertainment, aerospace and transportation may profit. For actuation usage, DE are typically shaped in thin films coated with compliant electrodes on both sides and piled one on the other to form a multilayered DE. DE-based Linear Actuators (DELA) are entirely constituted by polymeric materials and their overall performance is highly influenced by several interacting factors; firstly by the electromechanical properties of the film, secondly by the mechanical properties and geometry of the polymeric frame designed to support the film, and finally by the driving circuits and activation strategies. In the last decade, much effort has been focused in the devolvement of analytical and numerical models that could explain and predict the hyperelastic behavior of different types of DE materials. Nevertheless, at present, the use of DELA is limited. The main reasons are 1) the lack of quantitative and qualitative models of the actuator as a whole system 2) the lack of a simple and reliable design methodology. In this thesis, a new point of view in the study of DELA is presented which takes into account the interaction between the DE film and the film supporting frame. Hyperelastic models of the DE film are reported which are capable of modeling the DE and the compliant electrodes. The supporting frames are analyzed and designed as compliant mechanisms using pseudo-rigid body models and subsequent finite element analysis. A new design methodology is reported which optimize the actuator performances allowing to specifically choose its inherent stiffness. As a particular case, the methodology focuses on the design of constant force actuators. This class of actuators are an example of how the force control could be highly simplified. Three new DE actuator concepts are proposed which highlight the goodness of the proposed method.

No description available.

The wheel - rail contact analysis plays a fundamental role in the multibody modeling of railway vehicles. A good contact model must provide an accurate description of the global contact phenomena (contact forces and torques, number and position of the contact points) and of the local contact phenomena (position and shape of the contact patch, stresses and displacements). The model has also to assure high numerical efficiency (in order to be implemented directly online within multibody models) and a good compatibility with commercial multibody software (Simpack Rail, Adams Rail). The wheel - rail contact problem has been discussed by several authors and many models can be found in the literature. The contact models can be subdivided into two different categories: the global models and the local (or differential) models. Currently, as regards the global models, the main approaches to the problem are the so - called rigid contact formulation and the semi – elastic contact description. The rigid approach considers the wheel and the rail as rigid bodies. The contact is imposed by means of constraint equations and the contact points are detected during the dynamic simulation by solving the nonlinear algebraic differential equations associated to the constrained multibody system. Indentation between the bodies is not permitted and the normal contact forces are calculated through the Lagrange multipliers. Finally the Hertz’s and the Kalker’s theories allow to evaluate the shape of the contact patch and the tangential forces respectively. Also the semi - elastic approach considers the wheel and the rail as rigid bodies. However in this case no kinematic constraints are imposed and the indentation between the bodies is permitted. The contact points are detected by means of approximated procedures (based on look - up tables and simplifying hypotheses on the problem geometry). The normal contact forces are calculated as a function of the indentation while, as in the rigid approach, the Hertz’s and the Kalker’s theories allow to evaluate the shape of the contact patch and the tangential forces. Both the described multibody approaches are computationally very efficient but their generality and accuracy turn out to be often insufficient because the physical hypotheses behind these theories are too restrictive and, in many circumstances, unverified. In order to obtain a complete description of the contact phenomena, local (or differential) contact models are needed. In other words wheel and rail have to be considered elastic bodies governed by the Navier’s equations and the contact has to be described by suitable analytical contact conditions. The contact between elastic bodies has been widely studied in literature both in the general case and in the rolling case. Many procedures based on variational inequalities, FEM techniques and convex optimization have been developed. This kind of approach assures high generality and accuracy but still needs very large computational costs and memory consumption. Due to the high computational load and memory consumption, referring to the current state of the art, the integration between multibody and differential modeling is almost absent in literature especially in the railway field. However this integration is very important because only the differential modeling allows an accurate analysis of the contact problem (in terms of contact forces and torques, position and shape of the contact patch, stresses and displacements) while the multibody modeling is the standard in the study of the railway dynamics. In this thesis some innovative wheel – rail contact models developed during the Ph. D. activity will be described. Concerning the global models, two new models belonging to the semi – elastic approach will be presented; the models satisfy the following specifics: 1) the models have to be 3D and to consider all the six relative degrees of freedom between wheel and rail 2) the models have to consider generic railway tracks and generic wheel and rail profiles 3) the models have to assure a general and accurate handling of the multiple contact without simplifying hypotheses on the problem geometry; in particular the models have to evaluate the number and the position of the contact points and, for each point, the contact forces and torques 4) the models have to be implementable directly online within the multibody models without look - up tables 5) the models have to assure computation times comparable with those of commercial multibody software (Simpack Rail, Adams Rail) and compatible with RT and HIL applications 6) the models have to be compatible with commercial multibody software (Simpack Rail, Adams Rail). The most innovative aspect of the new global contact models regards the detection of the contact points. In particular both the models aim to reduce the algebraic problem dimension by means of suitable analytical techniques. This kind of reduction allows to obtain an high numerical efficiency that makes possible the online implementation of the new procedure and the achievement of performance comparable with those of commercial multibody software. At the same time the analytical approach assures high accuracy and generality. Concerning the local (or differential) contact models, one new model satisfying the following specifics will be presented: 1) the model has to be 3D and to consider all the six relative degrees of freedom between wheel and rail 2) the model has to consider generic railway tracks and generic wheel and rail profiles 3) the model has to assure a general and accurate handling of the multiple contact without simplifying hypotheses on the problem geometry; in particular the model has to able to calculate both the global contact variables (contact forces and torques) and the local contact variables (position and shape of the contact patch, stresses and displacements) 4) the model has to be implementable directly online within the multibody models 5) the model has to assure high numerical efficiency and a reduced memory consumption in order to achieve a good integration between multibody and differential modeling (the base for the local contact models) 6) the model has to be compatible with commercial multibody software (Simpack Rail, Adams Rail). In this case the most innovative aspects of the new local contact model regard the contact modeling (by means of suitable analytical conditions) and the implementation of the numerical algorithms needed to solve the discrete problem arising from the discretization of the original continuum problem. Moreover, during the development of the local model, the achievement of a good compromise between accuracy and efficiency turned out to be very important to obtain a good integration between multibody and differential modeling. At this point the contact models has been inserted within a 3D multibody model of a railway vehicle to obtain a complete model of the wagon. The railway vehicle chosen as benchmark is the Manchester Wagon the physical and geometrical characteristics of which are easily available in the literature. The model of the whole railway vehicle (multibody model and contact model) has been implemented in the Matlab/Simulink environment. The multibody model has been implemented in SimMechanics, a Matlab toolbox specifically designed for multibody dynamics, while, as regards the contact models, the CS – functions have been used; this particular Matlab architecture allows to efficiently connect the Matlab/Simulink and the C/C++ environment. The 3D multibody model of the same vehicle (this time equipped with a standard contact model based on the semi - elastic approach) has been then implemented also in Simpack Rail, a commercial multibody software for railway vehicles widely tested and validated. Finally numerical simulations of the vehicle dynamics have been carried out on many different railway tracks with the aim of evaluating the performances of the whole model. The comparison between the results obtained by the Matlab/ Simulink model and those obtained by the Simpack Rail model has allowed an accurate and reliable validation of the new contact models. In conclusion to this brief introduction to my Ph. D. thesis, we would like to thank Trenitalia and the Regione Toscana for the support provided during all the Ph. D. activity. Moreover we would also like to thank the INTEC GmbH, the society the develops the software Simpack Rail, with which we are currently working together to develop innovative toolboxes specifically designed for the wheel rail contact analysis.

Questa tesi affronta lo studio di una tipologia di vibrazione autoeccitata, nota come chatter, che si manifesta nei processi di lavorazione ad asportazione di truciolo ed in particolare nelle lavorazioni di fresatura. La tesi discute inoltre lo sviluppo di una tecnica di monitoraggio e diagnostica del chatter basato sul rilievo di vibrazioni. Il fenomeno del chatter è caratterizzato da violente oscillazioni tra utensile e pezzo in lavorazione ed elevate emissioni acustiche. Il chatter, se non controllato, causa uno scadimento qualitativo della finitura superficiale e delle tolleranze dimensionali del lavorato, una riduzione della vita degli utensili e dei componenti della macchina. Questa vibrazione affligge negativamente la produttività e la qualità del processo di lavorazione e pregiudica l’interazione uomo-macchina-ambiente. Per una data combinazione di macchina, utensile e pezzo lavorato, i fattori che controllano la velocità di asportazione del materiale sono gli stessi che controllano l’insorgenza del chatter: la velocità di rotazione del mandrino, la profondità assiale di passata e la velocità di avanzamento dell’utensile. Per studiare il fenomeno di chatter, con l’obbiettivo di individuare possibili soluzioni per limitarne o controllarne l’insorgenza, vengono proposti in questa tesi alcuni modelli del processo di fresatura. Tali modelli comprendono il modello viscoelastico della macchina fresatrice e il modello delle azioni di taglio. Per le azioni di taglio è stato utilizzato un modello presente in letteratura, mentre per la macchina fresatrice sono stati utilizzato modelli a parametri concentrati e modelli modali analitico-sperimentali. Questi ultimi sono stati ottenuti accoppiando un modello modale sperimentale del telaio, completo di mandrino, della macchina fresatrice con un modello analitico, basato sulla teoria delle travi, dell’utensile. Le equazioni del moto, associate al processo di fresatura, risultano essere equazioni differenziali con ritardo a coefficienti periodici o PDDE (Periodic Delay Diefferential Equations). È stata implementata una procedura numerica per mappare, nello spazio dei parametri di taglio, la stabilità e le caratteristiche spettrali (frequenze caratteristiche della vibrazione di chatter) delle equazioni del moto associate ai modelli del processo di fresatura proposti. Per testare i modelli e le procedure numeriche proposte, una macchina fresatrice CNC 4 assi, di proprietà del Dipartimento di Ingegneria delle Costruzioni Meccaniche Nucleari e Metallurgiche (DIEM) dell’Università di Bologna, è stata strumentata con accelerometri, con una tavola dinamometrica per la misura delle forze di taglio e con un adeguato sistema di acquisizione. Eseguendo varie prove di lavorazione sono stati identificati i coefficienti di pressione di taglio contenuti nel modello delle forze di taglio. Sono stati condotti, a macchina ferma, rilievi di FRFs (Funzioni Risposta in Frequenza) per identificare, tramite tecniche di analisi modale sperimentale, i modelli del solo telaio e della macchina fresatrice completa di utensile. I segnali acquisiti durante le numerose prove di lavorazione eseguite, al variare dei parametri di taglio, sono stati analizzati per valutare la stabilità di ciascun punto di lavoro e le caratteristiche spettrali della vibrazione associata. Questi risultati sono stati confrontati con quelli ottenuti applicando la procedura numerica proposta ai diversi modelli di macchina fresatrice implementati. Sono state individuate le criticità della procedura di modellazione delle macchine fresatrici a parametri concentrati, proposta in letteratura, che portano a previsioni erronee sulla stabilità delle lavorazioni. È stato mostrato come tali criticità vengano solo in parte superate con l’utilizzo dei modelli modali analitico-sperimentali proposti. Sulla base dei risultati ottenuti, è stato proposto un sistema automatico, basato su misure accelerometriche, per diagnosticare, in tempo reale, l’insorgenza del chatter durante una lavorazione. È stato realizzato un prototipo di tale sistema di diagnostica il cui funzionamento è stato provato mediante prove di lavorazione eseguite su due diverse macchine fresatrici CNC.

L’attività della tesi riguarda le protesi mioelettriche, gli arti protesici maggiormente diffusi, le quali sono descrivibili come arti robotici in cui i segmenti artificiali sono attuati da giunti elettromeccanici alimentati da batterie ricaricabili ed attivati mediante segnali elettromiografici (segnali elettrici generati dalla contrazione dei muscoli). Tali protesi di arto superiore attualmente disponibili in commercio potrebbero essere inadeguate per una riabilitazione soddisfacente di alcuni pazienti con una amputazione di alto livello che richiedono una elevata funzionalità nella vita quotidiana. In questo contesto si inserisce l’attività di ricerca del Centro Protesi INAIL di Budrio di Vigorso, Bologna, e dell’Università di Bologna i quali stanno sviluppando nuovi arti protesici con il progetto a lungo termine di rendere disponibili svariate soluzioni di protesi di arto superiore in grado di soddisfare la maggior parte delle richieste degli amputati. Lo scopo di questa tesi è l’introduzione di un nuovo rotatore omerale attivo da integrare alla protesi di arto superiore disponibile presso i nostri laboratori. Per ottenere questo risultato è stata utilizzata una procedura di progettazione già consolidata in attività precedenti per lo sviluppo di una protesi di spalla a due gradi di libertà. Differenti modelli cinematici sono stati studiati tramite analisi cinematiche per determinare l’incremento delle prestazioni a seguito dell’introduzione del nuovo rotatore omerale attivo. Sono state inoltre condotte analisi cinetostatiche per definire le specifiche tecniche di riferimento (in termini di carichi agenti sul rotatore omerale) e per guidare il dimensionamento della catena di trasmissione di potenza del nuovo dispositivo protesico. Ulteriori specifiche tecniche sono state considerate per garantire l’irreversibilità spontanea del moto sotto carichi esterni (quando i giunti attivi della protesi non sono alimentati), per salvaguardare l’incolumità del paziente in caso di caduta, per misurare la posizione angolare del rotatore omerale (in modo da implementare strategie di controllo in retroazione) e per limitare i consumi e la rumorosità del dispositivo. Uno studio di fattibilità ha permesso la selezione della architettura ottimale della catena di trasmissione di potenza per il nuovo rotatore omerale. I criteri di scelta sono stati principalmente la limitazione del peso e dell’ingombro del nuovo dispositivo protesico. Si è quindi proceduto con la progettazione di dettaglio alla quale è seguita la costruzione di un prototipo del nuovo rotatore omerale presso i nostri laboratori. La tesi tratta infine una attività preliminare di sperimentazione che ha permesso di fare considerazioni sulle prestazioni del prototipo ed osservazioni importanti per le successive attività di revisione ed ottimizzazione del progetto del rotatore omerale.

No description available.

Constraints are widely present in the flight control problems: actuators saturations or flight envelope limitations are only some examples of that. The ability of Model Predictive Control (MPC) of dealing with the constraints joined with the increased computational power of modern calculators makes this approach attractive also for fast dynamics systems such as agile air vehicles. This PhD thesis presents the results, achieved at the Aerospace Engineering Department of the University of Bologna in collaboration with the Dutch National Aerospace Laboratories (NLR), concerning the development of a model predictive control system for small scale rotorcraft UAS. Several different predictive architectures have been evaluated and tested by means of simulation, as a result of this analysis the most promising one has been used to implement three different control systems: a Stability and Control Augmentation System, a trajectory tracking and a path following system. The systems have been compared with a corresponding baseline controller and showed several advantages in terms of performance, stability and robustness.

The 3-UPU three degrees of freedom fully parallel manipulator, where U and P are for universal and prismatic pair respectively, is a very well known manipulator that can provide the platform with three degrees of freedom of pure translation, pure rotation or mixed translation and rotation with respect to the base, according to the relative directions of the revolute pair axes (each universal pair comprises two revolute pairs with intersecting and perpendicular axes). In particular, pure translational parallel 3-UPU manipulators (3-UPU TPMs) received great attention. Many studies have been reported in the literature on singularities, workspace, and joint clearance influence on the platform accuracy of this manipulator. However, much work has still to be done to reveal all the features this topology can offer to the designer when different architecture, i.e. different geometry are considered. Therefore, this dissertation will focus on this type of the 3-UPU manipulators. The first part of the dissertation presents six new architectures of the 3-UPU TPMs which offer interesting features to the designer. In the second part, a procedure is presented which is based on some indexes, in order to allows the designer to select the best architecture of the 3-UPU TPMs for a given task. Four indexes are proposed as stiffness, clearance, singularity and size of the manipulator in order to apply the procedure.