The results described in this dissertation have demonstrated several alternative proton exchange membranes (PEM) for hydrogen-air and direct methanol fuel cells (DMFC) that perform as well or better than the state of the art Nafion perfluorosulfonic acid membrane. Direct aromatic nucleophilic substitution polycondensations of disodium 3,3′ S-disulfonate-4,4′ S-difluorodiphenylsulfone (SDFDPS), 4,4′ S-difluorodiphenylsulfone (DFDPS) (or their chlorinated analogs, SDCDPS, DCDPS) and 4,4′ S-thiobisbenzenethiol (TBBT) in the presence of potassium carbonate were investigated. Electrophilic aromatic substitution was employed to synthesize the SDFDPS or SDCDPS comonomers in high yields and purity. High molecular weight disulfonated poly(arylene thioether sulfone) (PATS) copolymers were easily obtained using the SDFDPS monomers, but in general, slower rates and a lower molecular weight copolymer was obtained using the analogous chlorinated monomers. Tough and ductile membranes were solution cast from N,N-dimethylacetamide for both series of copolymers. The degrees of disulfonation (20-50%, PATS 20-50) were controlled by varying the ratio of disulfonated to unsulfonated comonomers. Composite membranes were prepared by homogeneous solution blending the copolymers with phosphotungstic acid (PTA) in dimethylacetamide (DMAc). The composite PATS membranes exhibited moderate PTA molecule water extraction after acidification treatments performed at either room or boiling temperatures. The membranes containing HPA showed improved conductivity at high temperatures (120 °C) and low relative humidities when compared to the pure copolymers. Molecular weight of the copolymers plays a critical role in the overall copolymer physical behavior. It is well known that molecular weight has an enormous impact on practically all of the physical properties of polymeric systems. This dissertation discusses the influence of molecular weight on the characteristics of a specific family of PEM PATS copolymers. This study elucidated that the lower molecular weight materials did indeed behave differently than the higher molecular weight copolymers. Specifically, the water uptake and permeability to methanol decreased with increasing molecular weight. Furthermore, the fully hydrated mechanical properties also improved with molecular weight. The synthesis and fabrication of 45 mole percent disulfonated poly(arylene ether phenyl phosphine oxide diphenyl sulfone) terpolymer-heteropolyacid (HPA) composite membranes and membrane electrode assemblies were chosen for detailed investigation. A series of 45 mole percent disulfonated biphenol-based poly(arylene ether phenyl phosphine oxide diphenyl sulfone) terpolymers (BPSH45-PPO) were also synthesized by nucleophilic aromatic substitution polymerizations. The level of disulfonation was constant at 45 mole percent providing a compromise between high conductivity at low humidity and reasonable mechanical properties in liquid water. The amounts of 4,4′-difluorodiphenyl phenyl phosphine oxide comonomer incorporated into the terpolymer backbone were precisely controlled from 0-50 mole percent relative to the 4,4′-dihalodiphenyl sulfone. Phosphine oxide moieties were employed to enhance the interactions with the PTA relative to the pure copolymer. The composite BPSH45-PPO membranes exhibited lower HPA molecule water extraction after acidification at room and boiling temperatures, which was ascribed to the strong hydrogen and polar interactions between the phosphine oxide moiety and functional groups on the HPA. The membranes containing HPA displayed improved conductivity at high temperatures and low relative humidities when compared to the pure terpolymer samples. The increase of proton conductivity was attributed to the water retention characteristics of the HPA molecules, which allowed enhanced mobility of the protons even at lower humidification levels, providing superior hydrogen-air fuel cell performance. The effect of hexafluoroisopropylidene bisphenol (6FBP) incorporation into 45 mole percent disulfonated poly(arylene ether sulfone) copolymers was investigated. This novel series of directly disulfonated poly(arylene ether sulfone) copolymers with various mole ratios of the 6FBP were synthesized in high molecular weight. The levels of fluorination within the statistically random copolymer architecture were varied from 0-100 mole percent using 6FBP and the correct stoichiometric amount of 4,4′-biphenol. The 6FBP monomer was introduced to decrease the water swelling and improve bonding characteristics with Nafion-bonded electrodes. Indeed, water uptake decreased with increasing incorporation of the 6FBP monomer into the terpolymer. This suggested that the hydrophobic fluorinated material aided in water repulsion of the system. Proton conductivity decreased slightly as the amount of fluorination increased, which was interpreted to be due to the decrease in the ion-exchange capacity. High temperature hydrogen/air fuel cell experiments indicated better Nafion-bonded electrode adhesion for the partially fluorinated materials, as depicted by high temperature (120 °C) and low humidity (50% RH) hydrogen-air fuel cell performance. Investigations into polymeric electromechanical transducers were based on poly(arylene sulfone) ion-exchange membranes bonded between two conductive metal layer electrodes. Imposed deformations and small electric fields allowed similar explorations of both sensing and actuation applications. These copolymers produced larger sensitivities than the benchmark Nafion systems, which was interpreted as being due to their higher hydrated moduli. Methodologies for better defining the morphology of the electrodes were identified to enhance the capacitance and effective interfacial area of the conductive electrodes. The new procedures afforded major improvements to performance and transduction. Transducer actuation at lower frequencies was improved by employing a new direct assembly electrode fabrication technique that suggested a strong correlation between the capacitance and charge motion. / Ph. D.

Thematic interrelation is an underdeveloped field of inquiry in Lukan studies. The design and elegance of Lukan theology begs for guided investigation into a possible system of organisation that governs history and theology, that is, narrative and theme. Based on the Greimasian Actantial Model, morpho–syntactical structural–critical analysis of Luke and Acts reveals that the covenant concept in its operative aspect of service functions as an organising principle, structuring the narratives and facilitating thematic interrelation. A survey of representative Lukan research consisting of five methodologically determined approaches shows a commonality regarding Lukan purpose. These all share the “plan of God” as a fundamental concept, thus intimating its plausibility as a common organisational principle in the text. This observation encourages further analysis of Lukan narrative and meta–narrative as relevant subject matter. Investigation into the purpose and goals of Ancient Jewish and Ancient Greek literature suggests that the concepts of piety/holiness and justness combined with a notion of divine order and expectation demonstrates organisational capacity. Under the terms and conditions of the Old Covenant three non–exclusive themes/concepts hold organisational functionality and ability to facilitate thematic interrelation: Exodus typology, the covenant concept and the eschaton idea. Exodus typology connects narrative with theme, developing Israel’s story. The covenant idea frames stories using parallelism and gives the meta–story progression. The eschaton idea presents the Day of YHWH as an organisational principle guiding the story of judgment to restoration. It is observed that the covenant concept is the most prevalent of these themes/ideas. Assuming the conceptual unity of Luke and Acts and adopting a morpho–syntactical structuralist approach, it was observed that the covenant concept in its operative aspect of service occurred as Helper at ten places, determining the development and structure of the meta–narrative. According to the Greimasian Actantial Model, Israel failed to fulfil its covenant–based mandate to serve God and shine God’s light of mercy to the nations. Jesus, Israel’s new Helper, becomes the Subject and by his covenant–based ministry, characterised as the greatest service, resolves the problem that prevents Israel from carrying out its divine mandate and sets the stage for its fulfilment. In Jesus Israel is given new leaders, an ethical platform of discipleship and the Holy Spirit. The apostle Paul as the epitomised and exemplary witness and servant of Jesus fulfils what Israel could not. He is vindicated in righteousness and shares in the Isaianic ministry of Jesus, to bear witness to leaders and to shine God’s light to the nations. Paul is unhindered in this ministry. Additionally, in thematic–critical terms, the key placement of the covenant concept in its operative aspect of service at plot–defining junctures features its catalytic dynamic as a “template” concept advancing the re–conceptualising of themes and providing a platform for meaningful relation. The evidence thus suggests that the covenant concept in its operative aspect structures the conjoined narratives of Luke and Acts. It also provides a basis for relation between the divine and humans in the context of the history of God’s salvation, linking history and theology, and makes possible a discernible means to thematic interrelation. The SO2 electrolysis was performed by supplying the anode of the cell with SO2 gas, while the water was fed to the cathode using graphite plates as flow fields. Initial experimental work was done at ambient pressures on the anode (SO2 gas–fed) and cathode (water–fed) after which the water pressure was increased from ambient to 1 bar. Various parameters were evaluated for SO2 electrolysis at ambient conditions, including operating temperature, membrane thickness and catalyst loading. The operating temperature was increased from 50oC to 80oC which resulted in a significant voltage improvement from 0.78V to 0.64V at 300mA/cm2. Operating the cell with thinner membranes (86 vs 170um) also resulted in an improved overall cell performance, while the catalyst loading (1 vs 0.5mgPt/cm2) had a negligible effect on the operating voltage. SEM images and EDX analysis were performed on the best performing MEA (N1135) which showed that no degradation of the MEA had occurred. / Thesis (M.Sc. (Chemistry))--North-West University, Potchefstroom Campus, 2011.

Thematic interrelation is an underdeveloped field of inquiry in Lukan studies. The design and elegance of Lukan theology begs for guided investigation into a possible system of organisation that governs history and theology, that is, narrative and theme. Based on the Greimasian Actantial Model, morpho–syntactical structural–critical analysis of Luke and Acts reveals that the covenant concept in its operative aspect of service functions as an organising principle, structuring the narratives and facilitating thematic interrelation. A survey of representative Lukan research consisting of five methodologically determined approaches shows a commonality regarding Lukan purpose. These all share the “plan of God” as a fundamental concept, thus intimating its plausibility as a common organisational principle in the text. This observation encourages further analysis of Lukan narrative and meta–narrative as relevant subject matter. Investigation into the purpose and goals of Ancient Jewish and Ancient Greek literature suggests that the concepts of piety/holiness and justness combined with a notion of divine order and expectation demonstrates organisational capacity. Under the terms and conditions of the Old Covenant three non–exclusive themes/concepts hold organisational functionality and ability to facilitate thematic interrelation: Exodus typology, the covenant concept and the eschaton idea. Exodus typology connects narrative with theme, developing Israel’s story. The covenant idea frames stories using parallelism and gives the meta–story progression. The eschaton idea presents the Day of YHWH as an organisational principle guiding the story of judgment to restoration. It is observed that the covenant concept is the most prevalent of these themes/ideas. Assuming the conceptual unity of Luke and Acts and adopting a morpho–syntactical structuralist approach, it was observed that the covenant concept in its operative aspect of service occurred as Helper at ten places, determining the development and structure of the meta–narrative. According to the Greimasian Actantial Model, Israel failed to fulfil its covenant–based mandate to serve God and shine God’s light of mercy to the nations. Jesus, Israel’s new Helper, becomes the Subject and by his covenant–based ministry, characterised as the greatest service, resolves the problem that prevents Israel from carrying out its divine mandate and sets the stage for its fulfilment. In Jesus Israel is given new leaders, an ethical platform of discipleship and the Holy Spirit. The apostle Paul as the epitomised and exemplary witness and servant of Jesus fulfils what Israel could not. He is vindicated in righteousness and shares in the Isaianic ministry of Jesus, to bear witness to leaders and to shine God’s light to the nations. Paul is unhindered in this ministry. Additionally, in thematic–critical terms, the key placement of the covenant concept in its operative aspect of service at plot–defining junctures features its catalytic dynamic as a “template” concept advancing the re–conceptualising of themes and providing a platform for meaningful relation. The evidence thus suggests that the covenant concept in its operative aspect structures the conjoined narratives of Luke and Acts. It also provides a basis for relation between the divine and humans in the context of the history of God’s salvation, linking history and theology, and makes possible a discernible means to thematic interrelation. The SO2 electrolysis was performed by supplying the anode of the cell with SO2 gas, while the water was fed to the cathode using graphite plates as flow fields. Initial experimental work was done at ambient pressures on the anode (SO2 gas–fed) and cathode (water–fed) after which the water pressure was increased from ambient to 1 bar. Various parameters were evaluated for SO2 electrolysis at ambient conditions, including operating temperature, membrane thickness and catalyst loading. The operating temperature was increased from 50oC to 80oC which resulted in a significant voltage improvement from 0.78V to 0.64V at 300mA/cm2. Operating the cell with thinner membranes (86 vs 170um) also resulted in an improved overall cell performance, while the catalyst loading (1 vs 0.5mgPt/cm2) had a negligible effect on the operating voltage. SEM images and EDX analysis were performed on the best performing MEA (N1135) which showed that no degradation of the MEA had occurred. / Thesis (M.Sc. (Chemistry))--North-West University, Potchefstroom Campus, 2011.

No description available.

Hydrogen production via the electrolysis of water has gained a lot of attention in the last couple of years. Research related to electrolysers is mostly aimed towards decreasing the noble–metal catalyst content. In this study the presently used catalyst application techniques were reviewed and critically examined to find commercially applicable and effective methods. Selected methods were then practically applied to determine their feasibility and to gain “know–how” related to the practical application of these techniques. The selected techniques were the hand paint, inkjet print, screen print and spray paint techniques. Meaningful comparisons were made between the methods in terms of parameters such as practicality, waste of catalyst and microstructure. The results point out that the hand paint and spray paint methods are feasible methods although there are improvements to be made. The hand paint method was improved by applying a carbon micro porous layer to the gas diffusion layer before the painting is carried out. The addition of the carbon layer reduced the soaking of the catalyst–containing ink through the gas diffusion layer. A method not initially investigated was identified an evaluated and showed promising results in lowering the mass of catalyst applied. This method comprised of sputtering a layer of catalyst material onto a prepared gas diffusion layer. It also came to light from the results that electrodes, and therefore membrane electrode assemblies, can be produced at a much lower cost than the commercial available membrane electrode assemblies. / Thesis (M.Ing. (Mechanical Engineering))--North-West University, Potchefstroom Campus, 2012.

Hydrogen production via the electrolysis of water has gained a lot of attention in the last couple of years. Research related to electrolysers is mostly aimed towards decreasing the noble–metal catalyst content. In this study the presently used catalyst application techniques were reviewed and critically examined to find commercially applicable and effective methods. Selected methods were then practically applied to determine their feasibility and to gain “know–how” related to the practical application of these techniques. The selected techniques were the hand paint, inkjet print, screen print and spray paint techniques. Meaningful comparisons were made between the methods in terms of parameters such as practicality, waste of catalyst and microstructure. The results point out that the hand paint and spray paint methods are feasible methods although there are improvements to be made. The hand paint method was improved by applying a carbon micro porous layer to the gas diffusion layer before the painting is carried out. The addition of the carbon layer reduced the soaking of the catalyst–containing ink through the gas diffusion layer. A method not initially investigated was identified an evaluated and showed promising results in lowering the mass of catalyst applied. This method comprised of sputtering a layer of catalyst material onto a prepared gas diffusion layer. It also came to light from the results that electrodes, and therefore membrane electrode assemblies, can be produced at a much lower cost than the commercial available membrane electrode assemblies. / Thesis (M.Ing. (Mechanical Engineering))--North-West University, Potchefstroom Campus, 2012.